|
Package: installation-reports Boot method: CD and USB key Image version: http://cdimage.debian.org/cdimage/daily-builds/daily/arch-latest/i386/iso-cd/ debian-testing-i386-netinst.iso 23 and 24-Jan-2012 Date: 23 and 24-Jan-2012 Machine: Dell Optiplex 260 and Dell Latitude D410 Processor: Petium 4 CPU 2GHz Memory: 1Go Partitions: NO SIGNIFICANT /dev/sda3 62G 9,4G 49G 16% / /dev/sdb1 184G 188M 174G 1% /data Output of lspci -knn (or lspci -nn): 00:00.0 Host bridge [0600]: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface [8086:2560] (rev 01) Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge [0604]: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge [8086:2561] (rev 01) Kernel modules: shpchp 00:1d.0 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 01) Kernel driver in use: uhci_hcd 00:1d.1 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 01) Kernel driver in use: uhci_hcd 00:1d.2 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 [8086:24c7] (rev 01) Kernel driver in use: uhci_hcd 00:1d.7 USB Controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller [8086:24cd] (rev 01) Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 81) Kernel modules: shpchp 00:1f.0 ISA bridge [0601]: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge [8086:24c0] (rev 01) Kernel modules: iTCO_wdt, intel-rng 00:1f.1 IDE interface [0101]: Intel Corporation 82801DB (ICH4) IDE Controller [8086:24cb] (rev 01) Kernel driver in use: ata_piix 00:1f.3 SMBus [0c05]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller [8086:24c3] (rev 01) Kernel modules: i2c-i801 00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 01) Kernel driver in use: Intel ICH Kernel modules: snd-intel8x0 01:00.0 VGA compatible controller [0300]: nVidia Corporation NV17 [GeForce4 MX 420] [10de:0172] (rev a3) Kernel driver in use: nouveau Kernel modules: nvidiafb, rivafb, nouveau 02:0c.0 Ethernet controller [0200]: Intel Corporation 82540EM Gigabit Ethernet Controller [8086:100e] (rev 02) Kernel driver in use: e1000 Kernel modules: e1000 Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot: [O] Detect network card: [E] Configure network: [E] Detect CD: [O] Load installer modules: [E] it stop here. Detect hard drives: [ ] Partition hard drives: [ ] Install base system: [ ] Clock/timezone setup: [ ] User/password setup: [ ] Install tasks: [ ] Install boot loader: [ ] Overall install: [ ] Comments/Problems: * First warning message just after the language choice : "No kernel modules were found. This probably is due to a mismatch between the kernel used by this version of installer and the kernel version availablein the archive. [...] COntinue the install without loadig kernel modules?" If I choose to continue the ethernet card is not recognize : "No ethernet card was detected.[...]" "Driver needed by your Ethernet card : No ethernet card hdlc none of above" Fisrt two choices loop back Third choice : "A driver for your hardware is not available. [...] Load missing drivers from removable media ?" If I choose Yes, the USB key not recognized. Here the installation stops. Thanks ! Bertrand |