Bug#628752: After install, system hangs during boot unless "nomodeset" is given
Package: installation-reports
Boot method: hard disk (netboot kernel + initrd) via grub
Image version: 20110525-00:09 (daily image)
Machine: Dell Dimension 2350
Processor: Intel(R) Pentium(R) 4 CPU 2.20GHz
Memory: 1GB
Partitions: ("fdisk -l" output below)
Disk /dev/sda: 120.0 GB, 120034123776 bytes
255 heads, 63 sectors/track, 14593 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0ea91612
Device Boot Start End Blocks Id System
/dev/sda1 1 9 72261 6 FAT16
/dev/sda2 10 14593 117145949+ 5 Extended
/dev/sda5 10 141 1060258+ 82 Linux swap /
Solaris
/dev/sda6 142 795 5253223+ 83 Linux
/dev/sda7 * 796 1840 8393931 83 Linux
/dev/sda8 1841 14593 102438441 83 Linux
Output of lspci -knn (or lspci -nn): (see attached)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [O]
Configure network: [O]
Detect CD: [ ]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [O]
Install boot loader: [O]
Overall install: [E]
Comments/Problems:
Installation of a minimal command-line-only system completed without
any trouble.
Booting into the installed system hangs at what appears to be the KMS
video-mode change. The screen goes black (without loss of video signal),
and the system becomes completely unresponsive: neither the Alt-SysRq
keys nor tapping the ACPI power button elicits a response. All I can do
then is power-cycle the system.
Booting with the "nomodeset" kernel parameter completes successfully,
yielding a login prompt.
Attached are kernel logs of the above two boot attempts, obtained via
serial console.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.38-2-686 (Debian 2.6.38-5) (ben@decadent.org.uk) (gcc version 4.4.6 (Debian 4.4.6-3) ) #1 SMP Sun May 8 14:49:45 UTC 2011
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
[ 0.000000] BIOS-e820: 000000003fef0000 - 000000003fef3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fef3000 - 000000003ff00000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] DMI 2.3 present.
[ 0.000000] last_pfn = 0x3fef0 max_arch_pfn = 0x100000
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [c00f4b80] f4b80
[ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[ 0.000000] RAMDISK: 36ec0000 - 37758000
[ 0.000000] ACPI: RSDP 000f6d00 00014 (v00 IntelR)
[ 0.000000] ACPI: RSDT 3fef3000 00030 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: FACP 3fef3040 00074 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: DSDT 3fef30c0 03543 (v01 INTELR AWRDACPI 00001000 MSFT 0100000C)
[ 0.000000] ACPI: FACS 3fef0000 00040
[ 0.000000] ACPI: BOOT 3fef6640 00028 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: APIC 3fef6680 00054 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] 134MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000377fe
[ 0.000000] HighMem 0x000377fe -> 0x0003fef0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0003fef0
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 3ff00000 (gap: 3ff00000:bed00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 12 pages/cpu @f6000000 s27136 r0 d22016 u4194304
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259713
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.38-2-686 root=UUID=8dd97169-ddbf-4fbe-a3ee-697047b28f73 ro console=ttyS0,115200
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000377fe:0003fef0)
[ 0.000000] Memory: 1024136k/1047488k available (2646k kernel code, 22900k reserved, 1389k data, 392k init, 138184k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd36000 - 0xfffff000 (2852 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc13f1000 - 0xc1453000 ( 392 kB)
[ 0.000000] .data : 0xc12959e4 - 0xc13f0e80 (1389 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12959e4 (2646 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [ttyS0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2193.057 MHz processor.
[ 0.012006] Calibrating delay loop (skipped), value calculated using timer frequency.. 4386.11 BogoMIPS (lpj=8772228)
[ 0.020007] pid_max: default: 32768 minimum: 301
[ 0.024109] Security Framework initialized
[ 0.028013] SELinux: Disabled at boot.
[ 0.032049] Mount-cache hash table entries: 512
[ 0.036469] Initializing cgroup subsys ns
[ 0.040011] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.044008] Initializing cgroup subsys cpuacct
[ 0.048037] Initializing cgroup subsys devices
[ 0.052008] Initializing cgroup subsys freezer
[ 0.056008] Initializing cgroup subsys net_cls
[ 0.060008] Initializing cgroup subsys blkio
[ 0.064082] CPU0: Hyper-Threading is disabled
[ 0.068011] mce: CPU supports 4 MCE banks
[ 0.072024] CPU0: Thermal monitoring enabled (TM1)
[ 0.076620] SMP alternatives: switching to UP code
[ 0.091314] Freeing SMP alternatives: 16k freed
[ 0.092024] ACPI: Core revision 20110112
[ 0.104122] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.108325] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.155550] CPU0: Intel(R) Pentium(R) 4 CPU 2.20GHz stepping 04
[ 0.164009] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[ 0.166622] ... version: 0
[ 0.168013] ... bit width: 40
[ 0.172012] ... generic registers: 18
[ 0.176013] ... value mask: 000000ffffffffff
[ 0.180013] ... max period: 0000007fffffffff
[ 0.184013] ... fixed-purpose events: 0
[ 0.188013] ... event mask: 000000000003ffff
[ 0.192382] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.196053] Brought up 1 CPUs
[ 0.200019] Total of 1 processors activated (4386.11 BogoMIPS).
[ 0.204697] devtmpfs: initialized
[ 0.208693] print_constraints: dummy:
[ 0.212131] NET: Registered protocol family 16
[ 0.216155] ACPI: bus type pci registered
[ 0.249721] PCI: PCI BIOS revision 2.10 entry at 0xfaea0, last bus=1
[ 0.252021] PCI: Using configuration type 1 for base access
[ 0.256749] bio: create slab <bio-0> at 0
[ 0.266962] ACPI: Interpreter enabled
[ 0.268033] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.273389] ACPI: Using IOAPIC for interrupt routing
[ 0.284427] ACPI: No dock devices found.
[ 0.288024] HEST: Table not found.
[ 0.291413] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.292111] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.300531] * The chipset may have PM-Timer Bug. Due to workarounds for a bug,
[ 0.300533] * this clock source is slow. If you are sure your timer does not have
[ 0.300535] * this bug, please use "acpi_pm_good" to disable the workaround
[ 0.305011] pci 0000:00:1e.0: PCI bridge to [bus 01-01] (subtractive decode)
[ 0.323970] ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 7 9 10 11 12 14 15)
[ 0.326702] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 0.334337] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.341528] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.348639] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.356277] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.365504] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.373866] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[ 0.380989] vgaarb: device added: PCI:0000:01:04.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.384032] vgaarb: loaded
[ 0.386778] PCI: Using ACPI for IRQ routing
[ 0.390483] pnp: PnP ACPI init
[ 0.392076] ACPI: bus type pnp registered
[ 0.396473] system 00:00: [mem 0x000d0000-0x000d3fff] has been reserved
[ 0.400039] system 00:00: [mem 0x000d9800-0x000dbfff] has been reserved
[ 0.404032] system 00:00: [mem 0x000f0000-0x000fbfff] could not be reserved
[ 0.408032] system 00:00: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.412033] system 00:00: [mem 0x3fef0000-0x3fefffff] could not be reserved
[ 0.416033] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.420033] system 00:00: [mem 0x00100000-0x3feeffff] could not be reserved
[ 0.424034] system 00:00: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.428034] system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.432034] system 00:00: [mem 0xffb00000-0xffbfffff] has been reserved
[ 0.436034] system 00:00: [mem 0xfff00000-0xffffffff] has been reserved
[ 0.440034] system 00:00: [mem 0x000e0000-0x000effff] has been reserved
[ 0.444363] system 00:02: [io 0x0400-0x04bf] has been reserved
[ 0.448399] system 00:03: [io 0x04d0-0x04d1] has been reserved
[ 0.452035] system 00:03: [io 0x0800-0x087f] has been reserved
[ 0.457277] pnp: PnP ACPI: found 11 devices
[ 0.460035] ACPI: ACPI bus type pnp unregistered
[ 0.464037] PnPBIOS: Disabled by ACPI PNP
[ 0.506122] Switching to clocksource acpi_pm
[ 0.508094] pci 0000:00:1f.1: BAR 5: assigned [mem 0x40000000-0x400003ff]
[ 0.514878] Switched to NOHz mode on CPU #0
[ 0.519092] pci 0000:00:1f.1: BAR 5: set to [mem 0x40000000-0x400003ff] (PCI address [0x40000000-0x400003ff])
[ 0.529014] pci 0000:01:04.0: BAR 6: assigned [mem 0xec000000-0xec01ffff pref]
[ 0.536245] pci 0000:01:06.0: BAR 6: assigned [mem 0xec020000-0xec02ffff pref]
[ 0.543474] pci 0000:01:09.0: BAR 6: assigned [mem 0xec030000-0xec033fff pref]
[ 0.550702] pci 0000:00:1e.0: PCI bridge to [bus 01-01]
[ 0.555939] pci 0000:00:1e.0: bridge window [io 0xc000-0xcfff]
[ 0.562043] pci 0000:00:1e.0: bridge window [mem 0xec000000-0xedffffff]
[ 0.568840] pci 0000:00:1e.0: bridge window [mem 0xd8000000-0xe7ffffff pref]
[ 0.576204] NET: Registered protocol family 2
[ 0.580707] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.588404] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.597263] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.604859] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.611521] TCP reno registered
[ 0.614689] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.620648] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.627603] NET: Registered protocol family 1
[ 0.632261] Unpacking initramfs...
[ 1.061450] Freeing initrd memory: 8800k freed
[ 1.082772] Simple Boot Flag at 0x59 set to 0x1
[ 1.087951] audit: initializing netlink socket (disabled)
[ 1.093430] type=2000 audit(1306538109.092:1): initialized
[ 1.110169] highmem bounce pool size: 64 pages
[ 1.114647] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.124074] VFS: Disk quotas dquot_6.5.2
[ 1.128178] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.134917] msgmni has been set to 1747
[ 1.139105] alg: No test for stdrng (krng)
[ 1.143320] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.150729] io scheduler noop registered
[ 1.154662] io scheduler deadline registered
[ 1.158972] io scheduler cfq registered (default)
[ 1.164048] ERST: Table is not found!
[ 1.167716] isapnp: Scanning for PnP cards...
[ 1.526555] isapnp: No Plug & Play device found
[ 1.531237] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.557906] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.584740] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.590576] Linux agpgart interface v0.103
[ 1.594807] agpgart-intel 0000:00:00.0: Intel 845G Chipset
[ 1.600337] agpgart-intel 0000:00:00.0: detected gtt size: 131072K total, 131072K mappable
[ 1.608777] agpgart-intel 0000:00:00.0: detected 1024K stolen memory
[ 1.615341] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xd0000000
[ 1.622353] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.629149] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.640203] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.645352] mousedev: PS/2 mouse device common for all mice
[ 1.651010] rtc_cmos 00:05: RTC can wake from S4
[ 1.655733] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.661870] rtc0: alarms up to one month, 242 bytes nvram
[ 1.667307] cpuidle: using governor ladder
[ 1.671427] cpuidle: using governor menu
[ 1.675834] TCP cubic registered
[ 1.679316] NET: Registered protocol family 10
[ 1.684863] Mobile IPv6
[ 1.687307] NET: Registered protocol family 17
[ 1.691906] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.700528] Registering the dns_resolver key type
[ 1.705286] Using IPI No-Shortcut mode
[ 1.709245] registered taskstats version 1
[ 1.713708] rtc_cmos 00:05: setting system clock to 2011-05-27 23:15:11 UTC (1306538111)
[ 1.721841] Initalizing network drop monitor service
[ 1.727013] Freeing unused kernel memory: 392k freed
[ 1.732716] Write protecting the kernel text: 2648k
[ 1.737686] Write protecting the kernel read-only data: 1000k
service
[ 2k freed
[ : 2648k
[ 1Loading, please wait...
: 1000k
service
[ 2k freed
[ : 2648k
[ 1Loading, please wait...
: 1000k
service
[ 1.776363] <30>udev[47]: starting version 167
[ 2k freed
[ : 2648k
[ 1Loading, ple
service
[ 1.776363] <30>udev[47]: starting version 167
[ 2k freed
[ : 2648k
[ 1Loading, ple
service
[ 2.058338] Floppy drive(s):
fd0 is 1.44M
[ 2.069437] 3c59x 0000:01:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 2.077171] 3c59x: Donald Becker and others.
[ 2.105069] Refined TSC clocksource calibration: 2192.883 MHz.
[ 1.776363] <30>udev[47]: starting version 167
[ 2.148346] 0000:01:06.0: 3Com PCI 3c905 Boomerang 100baseTx at 0001c400.
[ 2.192104] Switching to clocksource tsc
[ 2k freed
[ 2.276037] FDC 0 is a post-1991 82077
[ 2.333599] usbcore: registered new interface driver usbfs
[ 2.348475] SCSI subsystem initialized
[ 2.361639] usbcore: registered new interface driver hub
[ 2.373583] b44 0000:01:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 2.384188] usbcore: registered new device driver usb
[ 2.403551] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
: 2648k
[ 2.427304] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.460596] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 2.476098] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.487462] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 2.499625] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xee080000
[ 2.509653] ssb: Sonics Silicon Backplane found on PCI device 0000:01:09.0
[ 2.518429] b44: b44.c:v2.0
[ 2.528022] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.534973] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.543122] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.551762] usb usb1: Product: EHCI Host Controller
[ 2.558061] usb usb1: Manufacturer: Linux 2.6.38-2-686 ehci_hcd
[ 2.565407] usb usb1: SerialNumber: 0000:00:1d.7
[ 2.572590] b44 ssb0:0: eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:0b:db:2b:96:db
[ 2.581999] hub 1-0:1.0: USB hub found
[ 2.596460] hub 1-0:1.0: 6 ports detected
[ 2.602116] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.612861] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.618525] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.626058] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000d800
[ 2.632233] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.639076] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.646345] usb usb2: Product: UHCI Host Controller
[ 2.651273] usb usb2: Manufacturer: Linux 2.6.38-2-686 uhci_hcd
[ 2.657241] usb usb2: SerialNumber: 0000:00:1d.0
[ 2.662305] hub 2-0:1.0: USB hub found
[ 2.666123] hub 2-0:1.0: 2 ports detected
[ 2.670332] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 2.678603] scsi0 : ata_piix
[ 2.681837] scsi1 : ata_piix
[ 2.686124] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 2.693148] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 2.700568] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.708265] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.713686] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 2.721249] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d000
[ 2.727105] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.733946] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.741217] usb usb3: Product: UHCI Host Controller
[ 2.746143] usb usb3: Manufacturer: Linux 2.6.38-2-686 uhci_hcd
[ 2.752112] usb usb3: SerialNumber: 0000:00:1d.1
[ 2.757532] hub 3-0:1.0: USB hub found
[ 2.761356] hub 3-0:1.0: 2 ports detected
[ 2.765550] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.772757] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.778064] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 2.785559] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d400
[ 2.791406] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.798247] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.805515] usb usb4: Product: UHCI Host Controller
[ 2.810442] usb usb4: Manufacturer: Linux 2.6.38-2-686 uhci_hcd
[ 2.816413] usb usb4: SerialNumber: 0000:00:1d.2
[ 2.821988] hub 4-0:1.0: USB hub found
[ 2.825821] hub 4-0:1.0: 2 ports detected
[ 2.856497] ata2.00: ATAPI: Lite-On LTN486S 48x Max, YDS6, max UDMA/33
[ 2.868313] ata2.00: configured for UDMA/33
[ 2.976522] ata1.00: ATA-6: ST3120023A, 3.33, max UDMA/100
[ 2.982064] ata1.00: 234441648 sectors, multi 16: LBA
[ 3.000371] ata1.00: configured for UDMA/100
[ 3.004869] scsi 0:0:0:0: Direct-Access ATA ST3120023A 3.33 PQ: 0 ANSI: 5
[ 3.013960] scsi 1:0:0:0: CD-ROM Lite-On LTN486S 48x Max YDS6 PQ: 0 ANSI: 5
[ 3.065875] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 3.074151] sd 0:0:0:0: [sda] Write Protect is off
[ 3.079541] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.089796] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 3.096055] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.128054] usb 2-2: new low speed USB device using uhci_hcd and address 2
[ 3.147062] sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
[ 3.153085] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.187565] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.203463] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.359106] usb 2-2: New USB device found, idVendor=1267, idProduct=0213
[ 3.365939] usb 2-2: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 3.373197] usb 2-2: Product: PS/2+USB Mouse
[ 3.428698] input: PS/2+USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input1
[ 3.438797] generic-usb 0003:1267:0213.0001: input,hidraw0: USB HID v1.11 Mouse [PS/2+USB Mouse] on usb-0000:00:1d.0-2/input0
[ 3.451130] usbcore: registered new interface driver usbhid
[ 3.456777] usbhid: USB HID core driver
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-pr[ 3.928111] PM: Starting manual resume from disk
emount ... done.
[ 3.988796] EXT3-fs: barriers not enabled
[ 4.002503] kjournald starting. Commit interval 5 seconds
[ 4.008071] EXT3-fs (sda7): mounted filesystem with ordered data mode
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
[ 5.312347] <30>udev[274]: starting version 167
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...[ 5.799795] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 5.828899] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 5.840738] ACPI: Power Button [PWRB]
[ 5.847954] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 5.855789] ACPI: Power Button [PWRF]
[ 5.914265] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 5.967625] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 6.029699] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 6.142539] intel_rng: FWH not detected
[ 6.240595] [drm] Initialized drm 1.1.0 20060810
[ 6.500305] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 6.637277] Error: Driver 'pcspkr' is already registered, aborting...
[ 6.784643] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 6.819441] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 6.826150] [drm] Driver supports precise vblank timestamp query.
[ 6.860172] i915 0000:00:02.0: BAR 6: can't assign [??? 0x00000000 flags 0x0] (bogus alignment)
[ 6.868977] [drm] failed to find VBIOS tables
[ 6.973731] [drm] initialized overlay support
[ 6.981192] [drm] radeon defaulting to kernel modesetting.
[ 6.986758] [drm] radeon kernel modesetting enabled.
[ 6.998883] radeon 0000:01:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7.026427] No connectors reported connected with modes
[ 7.032261] [drm] Cannot find any crtc or sizes - going 1024x768
[ 7.058944] Console: switching to colour frame buffer device 128x48
[ 7.070098] fb0: inteldrmfb frame buffer device
[ 7.074679] drm: registered panic notifier
[ 7.079464] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 7.092330] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 7.108778] [drm] initializing kernel modesetting (RV280 0x1002:0x5960).
[ 7.115996] [drm] register mmio base: 0xED000000
[ 7.120765] [drm] register mmio size: 65536
[ 7.125464] [drm] Generation 2 PCI interface, using max accessible memory
[ 7.132406] radeon 0000:01:04.0: VRAM: 256M 0x00000000D8000000 - 0x00000000E7FFFFFF (256M used)
[ 7.141167] radeon 0000:01:04.0: GTT: 512M 0x00000000B8000000 - 0x00000000D7FFFFFF
[ 7.149372] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 7.156067] [drm] Driver supports precise vblank timestamp query.
[ 7.162637] [drm] radeon: irq initialized.
[ 7.168722] [drm] Detected VRAM RAM=256M, BAR=128M
[ 7.173632] [drm] RAM width 128bits DDR
[ 7.177708] [TTM] Zone kernel: Available graphics memory: 447580 kiB.
[ 7.184388] [TTM] Zone highmem: Available graphics memory: 516672 kiB.
[ 7.190982] [TTM] Initializing pool allocator.
[ 7.195712] [drm] radeon: 256M of VRAM memory ready
[ 7.201013] [drm] radeon: 512M of GTT memory ready.
[ 7.206096] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.38-2-686 (Debian 2.6.38-5) (ben@decadent.org.uk) (gcc version 4.4.6 (Debian 4.4.6-3) ) #1 SMP Sun May 8 14:49:45 UTC 2011
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
[ 0.000000] BIOS-e820: 000000003fef0000 - 000000003fef3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fef3000 - 000000003ff00000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] DMI 2.3 present.
[ 0.000000] last_pfn = 0x3fef0 max_arch_pfn = 0x100000
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [c00f4b80] f4b80
[ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[ 0.000000] RAMDISK: 36ec0000 - 37758000
[ 0.000000] ACPI: RSDP 000f6d00 00014 (v00 IntelR)
[ 0.000000] ACPI: RSDT 3fef3000 00030 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: FACP 3fef3040 00074 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: DSDT 3fef30c0 03543 (v01 INTELR AWRDACPI 00001000 MSFT 0100000C)
[ 0.000000] ACPI: FACS 3fef0000 00040
[ 0.000000] ACPI: BOOT 3fef6640 00028 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: APIC 3fef6680 00054 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] 134MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000377fe
[ 0.000000] HighMem 0x000377fe -> 0x0003fef0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0003fef0
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 3ff00000 (gap: 3ff00000:bed00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 12 pages/cpu @f6000000 s27136 r0 d22016 u4194304
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259713
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.38-2-686 root=UUID=8dd97169-ddbf-4fbe-a3ee-697047b28f73 ro nomodeset console=ttyS0,115200
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000377fe:0003fef0)
[ 0.000000] Memory: 1024136k/1047488k available (2646k kernel code, 22900k reserved, 1389k data, 392k init, 138184k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd36000 - 0xfffff000 (2852 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc13f1000 - 0xc1453000 ( 392 kB)
[ 0.000000] .data : 0xc12959e4 - 0xc13f0e80 (1389 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12959e4 (2646 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [ttyS0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2193.072 MHz processor.
[ 0.012006] Calibrating delay loop (skipped), value calculated using timer frequency.. 4386.14 BogoMIPS (lpj=8772288)
[ 0.020007] pid_max: default: 32768 minimum: 301
[ 0.024108] Security Framework initialized
[ 0.028013] SELinux: Disabled at boot.
[ 0.032049] Mount-cache hash table entries: 512
[ 0.036466] Initializing cgroup subsys ns
[ 0.040011] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.044009] Initializing cgroup subsys cpuacct
[ 0.048037] Initializing cgroup subsys devices
[ 0.052008] Initializing cgroup subsys freezer
[ 0.056009] Initializing cgroup subsys net_cls
[ 0.060008] Initializing cgroup subsys blkio
[ 0.064082] CPU0: Hyper-Threading is disabled
[ 0.068011] mce: CPU supports 4 MCE banks
[ 0.072024] CPU0: Thermal monitoring enabled (TM1)
[ 0.076620] SMP alternatives: switching to UP code
[ 0.091305] Freeing SMP alternatives: 16k freed
[ 0.092025] ACPI: Core revision 20110112
[ 0.104121] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.108325] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.155691] CPU0: Intel(R) Pentium(R) 4 CPU 2.20GHz stepping 04
[ 0.164009] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[ 0.166622] ... version: 0
[ 0.168013] ... bit width: 40
[ 0.172012] ... generic registers: 18
[ 0.176013] ... value mask: 000000ffffffffff
[ 0.180013] ... max period: 0000007fffffffff
[ 0.184013] ... fixed-purpose events: 0
[ 0.188013] ... event mask: 000000000003ffff
[ 0.192383] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.196053] Brought up 1 CPUs
[ 0.200019] Total of 1 processors activated (4386.14 BogoMIPS).
[ 0.204696] devtmpfs: initialized
[ 0.208703] print_constraints: dummy:
[ 0.212131] NET: Registered protocol family 16
[ 0.216158] ACPI: bus type pci registered
[ 0.249732] PCI: PCI BIOS revision 2.10 entry at 0xfaea0, last bus=1
[ 0.252020] PCI: Using configuration type 1 for base access
[ 0.256754] bio: create slab <bio-0> at 0
[ 0.267021] ACPI: Interpreter enabled
[ 0.268033] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.273389] ACPI: Using IOAPIC for interrupt routing
[ 0.284525] ACPI: No dock devices found.
[ 0.288025] HEST: Table not found.
[ 0.291412] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.292111] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.300633] * The chipset may have PM-Timer Bug. Due to workarounds for a bug,
[ 0.300635] * this clock source is slow. If you are sure your timer does not have
[ 0.300637] * this bug, please use "acpi_pm_good" to disable the workaround
[ 0.305014] pci 0000:00:1e.0: PCI bridge to [bus 01-01] (subtractive decode)
[ 0.324090] ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 7 9 10 11 12 14 15)
[ 0.330701] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 0.338337] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.345528] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.352906] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.361238] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.369599] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.377867] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[ 0.385258] vgaarb: device added: PCI:0000:01:04.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.388032] vgaarb: loaded
[ 0.392083] PCI: Using ACPI for IRQ routing
[ 0.398483] pnp: PnP ACPI init
[ 0.400075] ACPI: bus type pnp registered
[ 0.404461] system 00:00: [mem 0x000d0000-0x000d3fff] has been reserved
[ 0.408039] system 00:00: [mem 0x000d9800-0x000dbfff] has been reserved
[ 0.412033] system 00:00: [mem 0x000f0000-0x000fbfff] could not be reserved
[ 0.416033] system 00:00: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.420033] system 00:00: [mem 0x3fef0000-0x3fefffff] could not be reserved
[ 0.424033] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.428034] system 00:00: [mem 0x00100000-0x3feeffff] could not be reserved
[ 0.432034] system 00:00: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.436034] system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.440034] system 00:00: [mem 0xffb00000-0xffbfffff] has been reserved
[ 0.444035] system 00:00: [mem 0xfff00000-0xffffffff] has been reserved
[ 0.448035] system 00:00: [mem 0x000e0000-0x000effff] has been reserved
[ 0.456036] system 00:02: [io 0x0400-0x04bf] has been reserved
[ 0.460396] system 00:03: [io 0x04d0-0x04d1] has been reserved
[ 0.464036] system 00:03: [io 0x0800-0x087f] has been reserved
[ 0.469277] pnp: PnP ACPI: found 11 devices
[ 0.472036] ACPI: ACPI bus type pnp unregistered
[ 0.476038] PnPBIOS: Disabled by ACPI PNP
[ 0.518396] Switching to clocksource acpi_pm
[ 0.520094] pci 0000:00:1f.1: BAR 5: assigned [mem 0x40000000-0x400003ff]
[ 0.526879] Switched to NOHz mode on CPU #0
[ 0.531093] pci 0000:00:1f.1: BAR 5: set to [mem 0x40000000-0x400003ff] (PCI address [0x40000000-0x400003ff])
[ 0.541015] pci 0000:01:04.0: BAR 6: assigned [mem 0xec000000-0xec01ffff pref]
[ 0.548245] pci 0000:01:06.0: BAR 6: assigned [mem 0xec020000-0xec02ffff pref]
[ 0.555475] pci 0000:01:09.0: BAR 6: assigned [mem 0xec030000-0xec033fff pref]
[ 0.562703] pci 0000:00:1e.0: PCI bridge to [bus 01-01]
[ 0.567939] pci 0000:00:1e.0: bridge window [io 0xc000-0xcfff]
[ 0.574045] pci 0000:00:1e.0: bridge window [mem 0xec000000-0xedffffff]
[ 0.580843] pci 0000:00:1e.0: bridge window [mem 0xd8000000-0xe7ffffff pref]
[ 0.588207] NET: Registered protocol family 2
[ 0.592713] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.600410] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.609262] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.616862] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.623521] TCP reno registered
[ 0.626688] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.632647] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.639348] NET: Registered protocol family 1
[ 0.643984] Unpacking initramfs...
[ 1.073452] Freeing initrd memory: 8800k freed
[ 1.094723] Simple Boot Flag at 0x59 set to 0x1
[ 1.099952] audit: initializing netlink socket (disabled)
[ 1.105419] type=2000 audit(1306538238.104:1): initialized
[ 1.121805] highmem bounce pool size: 64 pages
[ 1.126284] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.135689] VFS: Disk quotas dquot_6.5.2
[ 1.139809] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.146554] msgmni has been set to 1747
[ 1.150742] alg: No test for stdrng (krng)
[ 1.154958] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.162369] io scheduler noop registered
[ 1.166303] io scheduler deadline registered
[ 1.170614] io scheduler cfq registered (default)
[ 1.175666] ERST: Table is not found!
[ 1.179369] isapnp: Scanning for PnP cards...
[ 1.538122] isapnp: No Plug & Play device found
[ 1.542800] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.569465] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.596271] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.602107] Linux agpgart interface v0.103
[ 1.606338] agpgart-intel 0000:00:00.0: Intel 845G Chipset
[ 1.611870] agpgart-intel 0000:00:00.0: detected gtt size: 131072K total, 131072K mappable
[ 1.620310] agpgart-intel 0000:00:00.0: detected 1024K stolen memory
[ 1.626874] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xd0000000
[ 1.633887] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.640684] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.651767] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.656922] mousedev: PS/2 mouse device common for all mice
[ 1.662580] rtc_cmos 00:05: RTC can wake from S4
[ 1.667299] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.673436] rtc0: alarms up to one month, 242 bytes nvram
[ 1.678871] cpuidle: using governor ladder
[ 1.682991] cpuidle: using governor menu
[ 1.687383] TCP cubic registered
[ 1.690864] NET: Registered protocol family 10
[ 1.696349] Mobile IPv6
[ 1.698791] NET: Registered protocol family 17
[ 1.703386] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.712029] Registering the dns_resolver key type
[ 1.716783] Using IPI No-Shortcut mode
[ 1.720740] registered taskstats version 1
[ 1.725196] rtc_cmos 00:05: setting system clock to 2011-05-27 23:17:20 UTC (1306538240)
[ 1.733329] Initalizing network drop monitor service
[ 1.738513] Freeing unused kernel memory: 392k freed
[ 1.744241] Write protecting the kernel text: 2648k
[ 1.749203] Write protecting the kernel read-only data: 1000k
twork drop monitd kernel memory: 392k fre kernel text: 2Loading, please wait...
kernel read-only data: 1000k
twork drop monitd kernel memory: 392k fre kernel text: 2Loading, please wait...
kernel read-only data: 1000k
twork drop monitd kernel memory: 392k fre kernel text: 2Loading, please wait...
kernel read-on[ 1.788378] <30>udev[47]: starting version 167
ly data: 1000k
twork drop monitd kernel memory: 392k fre kernel
kernel read-on[ 1.788378] <30>udev[47]: starting version 167
ly data: 1000k
twork drop monitd kernel memory: 392k fre kernel
kernel read-on[ 1.788378] <30>udev[47]: starting version 167
ly data: 1000k
[ 2.066207] 3c59x 0000:01:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 2.073640] 3c59x: Donald Becker and others.
twork drop monitd kernel memory: 392k fre kernel
[ 2.111933] Floppy drive(s):
fd0 is 1.44M
[ 2.135274] Refined TSC clocksource calibration: 2192.884 MHz.
[ 2.196217] 0000:01:06.0: 3Com PCI 3c905 Boomerang 100baseTx at 0001c400.
[ 2.205065] Switching to clocksource tsc
[ 2.261423] usbcore: registered new interface driver usbfs
kernel read-on[ 1.788378] <30>udev[47]: starting version 167
ly data: 1000k
[ 2.304842] FDC 0 is a post-1991 82077
[ 2.325571] SCSI subsystem initialized
[ 2.332689] usbcore: registered new interface driver hub
[ 2.356189] usbcore: registered new device driver usb
[ 2.370869] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.398271] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 2.420113] b44 0000:01:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 2.454911] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.467508] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 2.481181] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xee080000
[ 2.500020] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.506598] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.514471] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.523108] usb usb1: Product: EHCI Host Controller
[ 2.529410] usb usb1: Manufacturer: Linux 2.6.38-2-686 ehci_hcd
[ 2.536749] usb usb1: SerialNumber: 0000:00:1d.7
[ 2.546615] hub 1-0:1.0: USB hub found
[ 2.550444] hub 1-0:1.0: 6 ports detected
[ 2.554672] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 2.575357] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.582495] scsi0 : ata_piix
[ 2.585855] scsi1 : ata_piix
[ 2.589784] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 2.596807] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 2.603908] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.611863] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.617517] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.625092] ssb: Sonics Silicon Backplane found on PCI device 0000:01:09.0
[ 2.632194] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000d800
[ 2.638366] b44: b44.c:v2.0
[ 2.641298] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.648140] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.655411] usb usb2: Product: UHCI Host Controller
[ 2.660338] usb usb2: Manufacturer: Linux 2.6.38-2-686 uhci_hcd
[ 2.666303] usb usb2: SerialNumber: 0000:00:1d.0
[ 2.671749] hub 2-0:1.0: USB hub found
[ 2.675575] hub 2-0:1.0: 2 ports detected
[ 2.679783] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.687151] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.693601] b44 ssb0:0: eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:0b:db:2b:96:db
[ 2.701865] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 2.709753] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d000
[ 2.715639] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.722481] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.729747] usb usb3: Product: UHCI Host Controller
[ 2.734671] usb usb3: Manufacturer: Linux 2.6.38-2-686 uhci_hcd
[ 2.740638] usb usb3: SerialNumber: 0000:00:1d.1
[ 2.746069] hub 3-0:1.0: USB hub found
[ 2.749899] hub 3-0:1.0: 2 ports detected
[ 2.754093] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.761306] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.767052] ata2.00: ATAPI: Lite-On LTN486S 48x Max, YDS6, max UDMA/33
[ 2.773809] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 2.781593] ata2.00: configured for UDMA/33
[ 2.785940] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d400
[ 2.791999] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.798848] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.806116] usb usb4: Product: UHCI Host Controller
[ 2.811043] usb usb4: Manufacturer: Linux 2.6.38-2-686 uhci_hcd
[ 2.817012] usb usb4: SerialNumber: 0000:00:1d.2
[ 2.822430] hub 4-0:1.0: USB hub found
[ 2.826258] hub 4-0:1.0: 2 ports detected
[ 2.884541] ata1.00: ATA-6: ST3120023A, 3.33, max UDMA/100
[ 2.890082] ata1.00: 234441648 sectors, multi 16: LBA
[ 2.908443] ata1.00: configured for UDMA/100
[ 2.912944] scsi 0:0:0:0: Direct-Access ATA ST3120023A 3.33 PQ: 0 ANSI: 5
[ 2.921997] scsi 1:0:0:0: CD-ROM Lite-On LTN486S 48x Max YDS6 PQ: 0 ANSI: 5
[ 2.983000] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 2.991257] sd 0:0:0:0: [sda] Write Protect is off
[ 2.996233] usb 2-2: new low speed USB device using uhci_hcd and address 2
[ 3.003209] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.013526] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 3.019788] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.063349] sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
[ 3.069347] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.105628] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.121873] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.187200] usb 2-2: New USB device found, idVendor=1267, idProduct=0213
[ 3.193980] usb 2-2: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 3.201164] usb 2-2: Product: PS/2+USB Mouse
[ 3.272273] input: PS/2+USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input1
[ 3.282477] generic-usb 0003:1267:0213.0001: input,hidraw0: USB HID v1.11 Mouse [PS/2+USB Mouse] on usb-0000:00:1d.0-2/input0
[ 3.294979] usbcore: registered new interface driver usbhid
[ 3.300650] usbhid: USB HID core driver
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-pr[ 3.785812] PM: Starting manual resume from disk
emount ... done.
[ 3.846616] EXT3-fs: barriers not enabled
[ 3.860321] kjournald starting. Commit interval 5 seconds
[ 3.865881] EXT3-fs (sda7): mounted filesystem with ordered data mode
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel S.
[ 5.145023] <30>udev[277]: starting version 167
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
[ 5.474936] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 5.607106] ACPI: Power Button [PWRB]
[ 5.611845] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 5.621637] ACPI: Power Button [PWRF]
Waiting for /dev to be fully populated...[ 5.670336] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 5.706183] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 5.749952] intel_rng: FWH not detected
[ 5.813779] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 5.838836] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 5.861645] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 6.495531] [drm] Initialized drm 1.1.0 20060810
[ 6.555877] Error: Driver 'pcspkr' is already registered, aborting...
[ 6.632285] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 6.686257] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 6.715125] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 6.721952] [drm] No driver support for vblank timestamp query.
[ 6.728640] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 7.060025] intel8x0_measure_ac97_clock: measured 53206 usecs (2564 samples)
[ 7.067243] intel8x0: clocking to 48000
[ 7.229111] [drm] VGACON disable radeon kernel modesetting.
[ 7.235288] pci 0000:01:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7.244668] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 7.251375] [drm] No driver support for vblank timestamp query.
[ 7.257343] [drm] Initialized radeon 1.33.0 20080528 for 0000:01:04.0 on minor 1
done.
Setting the system clock.
Setting preliminary keymap...done.
Activating swap...[ 8.038240] Adding 1060252k swap on /dev/sda5. Priority:-1 extents:1 across:1060252k
done.
Checking root file system...fsck from util-linux-ng 2.17.2
root: clean, 15945/525200 files, 168131/2098482 blocks
done.
[ 8.240424] EXT3-fs (sda7): using internal journal
Cleaning up ifupdown....
Setting up networking....
[ 8.417063] loop: module loaded
Loading kernel modules...done.
Setting the system clock.
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux-ng 2.17.2
done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Cleaning up temporary files....
Configuring network interfaces...done.
Cleaning up temporary files....
Setting console screen modes.
]Rcannot (un)set powersave mode
[9;30][14;30]Skipping font and keymap setup (handled by console-setup).
[ 9.646247] eth0: setting half-duplex.
Setting up console font and keymap...done.
Setting kernel variables ...done.
INIT: Entering runlevel: 2
[ 9.981262] ttyS0: 1 input overrun(s)
Using makefile-style concurrent boot in runlevel S.
Using makefile-style concurrent boot in runlevel 2.
Starting enhanced syslogd: rsyslogd.
Starting ACPI services....
Starting periodic command scheduler: cron.
00:00.0 Host bridge [0600]: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface [8086:2560] (rev 03)
Subsystem: Dell Device [1028:0147]
Kernel driver in use: agpgart-intel
00:02.0 Display controller [0380]: Intel Corporation 82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device [8086:2562] (rev 03)
Subsystem: Dell Device [1028:0147]
00:1d.0 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 02)
Subsystem: Dell Device [1028:0147]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 02)
Subsystem: Dell Device [1028:0147]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 [8086:24c7] (rev 02)
Subsystem: Dell Device [1028:0147]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller [8086:24cd] (rev 02)
Subsystem: Dell Device [1028:0147]
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 82)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge [8086:24c0] (rev 02)
00:1f.1 IDE interface [0101]: Intel Corporation 82801DB (ICH4) IDE Controller [8086:24cb] (rev 02)
Subsystem: Dell Device [1028:0147]
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller [8086:24c3] (rev 02)
Subsystem: Dell Device [1028:0147]
Kernel driver in use: i801_smbus
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 02)
Subsystem: Dell Device [1028:0147]
Kernel driver in use: Intel ICH
01:04.0 VGA compatible controller [0300]: ATI Technologies Inc RV280 [Radeon 9200 PRO] [1002:5960] (rev 01)
Subsystem: C.P. Technology Co. Ltd Device [148c:2095]
01:04.1 Display controller [0380]: ATI Technologies Inc RV280 [Radeon 9200 PRO] (Secondary) [1002:5940] (rev 01)
Subsystem: C.P. Technology Co. Ltd Device [148c:2094]
01:06.0 Ethernet controller [0200]: 3Com Corporation 3c905 100BaseTX [Boomerang] [10b7:9050]
Kernel driver in use: 3c59x
01:09.0 Ethernet controller [0200]: Broadcom Corporation BCM4401 100Base-T [14e4:4401] (rev 01)
Subsystem: Dell Device [1028:8127]
Kernel driver in use: b44
Reply to: