--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: installation-reports: beta-1 hp kayak
- From: Hans Fugal <hans@fugal.net>
- Date: Thu, 13 Nov 2003 05:00:50 -0700
- Message-id: <E1AKG9a-0007HD-US@vmacserv.et.byu.edu>
Package: installation-reports
Severity: normal
Package: installation-reports
INSTALL REPORT
Debian-installer-version: beta-1 (sarge netinst 100M)
uname -a: Linux localhost 2.4.22-1-386 #9 Sat Oct 4 14:30:39 EST 2003 i686 GNU/Linux
Date: 13 Nov 2003, 7:00
Method: Boot off atapi cdrom, install from cdrom (just pressed enter)
Machine: HP Kayak XAs
Processor: Pentium III 500 MHz
Memory: 256
Root Device: SCSI 0,0,0
Root Size/partition table:
Filesystem Size Used Avail Use% Mounted on
/dev/sda1 5.0G 301M 4.5G 7% /
Output of lspci:
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
00:13.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03)
01:00.0 VGA compatible controller: Texas Instruments TVP4020 [Permedia 2] (rev 11)
02:04.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 26)
02:05.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 36)
Base System Installation Checklist:
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Comments/Problems:
When setting up filesystems, I selected my swap partition (already existing
from a previous mandrake install) and told it to make a it a swap, then it
returned to the filesystems screen and had assigned the mount point from the
previous partition that I had configured (/mnt/mandrake, from sda7) I think
that's a bug. I went back and told it to leave the filesystem alone and it
returned to its initial state.
I initially chose woody instead of sarge when presented with the choice, and
when I discovered that the woody files weren't on the CD there was no way to
change that choice without rebooting and starting over. There should either be
a way to change that choice or to not present options that aren't applicable to
this particular CD.
When asked where to put LILO - the existing option was a devfs path. I
understood it but a newbie would shake in his or her pants. If I had needed to
change it even I would have been at a complete loss as to what to put, because
devfs paths are so hard to remember. A selection box would have been real nice
here.
The installer recognized my ide controller and disks/cdrom just fine,
but when I booted into the system (kernel-image-2.4.22-1-386) they were
nowhere to be found. May not be an installer issue, but it was annoying.
The install worked WONDERFULLY. This has really come a long way!
-- System Information:
Debian Release: testing/unstable
Architecture: i386
Kernel: Linux vmacserv 2.4.22-1-686 #6 Sat Oct 4 14:09:08 EST 2003 i686
Locale: LANG=C, LC_CTYPE=C
--- End Message ---