--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: installation-report: partial success, but problems
- From: Paul E Condon <pecondon@mesanetworks.net>
- Date: Sat, 08 Nov 2008 16:13:13 -0700
- Message-id: <20081108231313.18396.42940.reportbug@localhost>
Package: installation-reports
Version: 2.29
Severity: wishlist
-- Package-specific info:
Boot method: CD
Image version: LennyBeta2
Date: <Date and time of the install>
Machine: i386 grey boxes
Partitions: <df -Tl will do; the raw partition table is preferred>
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O} [E] [O]
Detect network card: [O] [ ] [ ]
Configure network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [O]
Install boot loader: [O]
Overall install: [O]
Comments/Problems:
<Description of the install, in prose, and any thoughts, comments
and ideas you had during the initial install.>
I have three computers running Etch and enough spare disk space to attempt to install
Lenny on all of them. After a false start with a bad CD burn, I succeeded on the first
machine, but the second machine would not boot from the netinst disk. I checked the
boot sequence settings in the bios. They were correct. (I had previously installed
first Sarge and then Etch from netinst disks on this machine so I would have been
surprised if the settings had changed.) I tried several times, burned a new CD, but
could not get this machine to boot from LennyBeta2 iso image.
I tried the thirs machine. On this, I was able to boot from the Lenny netinst CD.
I didn't go beyond the welcome screen because I really wanted to do the third
machine last. I poked around for several days looking for differences that made
the second machine different from the other two. The only thing that I could find
was that the two machines have bios from American Megatrends, and the one that
will not boot off of LennyBeta2 has bios from Award.
I will attempt to set up email on the box that had the problem and see
if I can send a repeat of this report from that machine.
--
Please make sure that the hardware-summary log file, and any otherOn all of these
machines, I installed Etch by netinst with no problems.
The third machine is an old Gateway. The first is a newish grey box that I assembled
with the help of a local computer shop. The second and problem computer is
a "Great Quality" that I purchased from Fry's in Sacramento in 2002.
I'll be glad to answer any more detailed questions that you can think to ask.
I'd like to move my little shop to Lenny as soon as it is released.
installation logs that you think would be useful are attached to this
report. Please compress large files using gzip.
Once you have filled out this report, mail it to submit@bugs.debian.org.
==============================================
Installer lsb-release:
==============================================
DISTRIB_ID=Debian
DISTRIB_DESCRIPTION="Debian GNU/Linux installer"
DISTRIB_RELEASE="4.0 (installer build 20070308etch2)"
X_INSTALLATION_MEDIUM=cdrom
==============================================
Installer hardware-summary:
==============================================
umame -a: Linux big 2.6.18-6-486 #1 Sat Jan 26 08:50:43 UTC 2008 i686 unknown
lspci -nn: 00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:0351]
lspci -nn: 00:00.1 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:1351]
lspci -nn: 00:00.2 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:2351]
lspci -nn: 00:00.3 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:3351]
lspci -nn: 00:00.4 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:4351]
lspci -nn: 00:00.5 PIC [0800]: VIA Technologies, Inc. VT3351 I/O APIC Interrupt Controller [1106:5351]
lspci -nn: 00:00.6 Host bridge [0600]: VIA Technologies, Inc. Unknown device [1106:6238]
lspci -nn: 00:00.7 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:7351]
lspci -nn: 00:01.0 PCI bridge [0604]: VIA Technologies, Inc. [K8T890 North / VT8237 South] PCI Bridge [1106:b999]
lspci -nn: 00:02.0 PCI bridge [0604]: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller [1106:a238]
lspci -nn: 00:03.0 PCI bridge [0604]: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller [1106:c238]
lspci -nn: 00:03.1 PCI bridge [0604]: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller [1106:d238]
lspci -nn: 00:03.2 PCI bridge [0604]: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller [1106:e238]
lspci -nn: 00:03.3 PCI bridge [0604]: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller [1106:f238]
lspci -nn: 00:0f.0 IDE interface [0101]: VIA Technologies, Inc. VT8237A SATA 2-Port Controller [1106:0591] (rev 80)
lspci -nn: 00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 07)
lspci -nn: 00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0)
lspci -nn: 00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0)
lspci -nn: 00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0)
lspci -nn: 00:10.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0)
lspci -nn: 00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 86)
lspci -nn: 00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237A PCI to ISA Bridge [1106:3337]
lspci -nn: 00:11.7 Host bridge [0600]: VIA Technologies, Inc. VT8251 Ultra VLINK Controller [1106:287e]
lspci -nn: 00:13.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237A Host Bridge [1106:337b]
lspci -nn: 00:13.1 PCI bridge [0604]: VIA Technologies, Inc. VT8237A PCI to PCI Bridge [1106:337a]
lspci -nn: 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
lspci -nn: 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
lspci -nn: 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
lspci -nn: 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
lspci -nn: 02:00.0 VGA compatible controller [0300]: nVidia Corporation NV44 [GeForce 6200 TurboCache(TM)] [10de:0161] (rev a1)
lspci -nn: 04:00.0 Ethernet controller [0200]: Unknown device [1969:1048] (rev b0)
lspci -nn: 06:00.0 SATA controller [0106]: Marvell Technology Group Ltd. Unknown device [11ab:6121] (rev b0)
lspci -nn: 07:06.0 Ethernet controller [0200]: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller [100b:0020]
lspci -nn: 08:01.0 Audio device [0403]: VIA Technologies, Inc. VIA High Definition Audio Controller [1106:3288] (rev 10)
lspci -vnn: 00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:0351]
lspci -vnn: Subsystem: VIA Technologies, Inc. VT3351 Host Bridge [1106:0351]
lspci -vnn: Flags: bus master, medium devsel, latency 64
lspci -vnn: Capabilities: [50] Power Management version 2
lspci -vnn: Capabilities: [60] HyperTransport: Slave or Primary Interface
lspci -vnn: Capabilities: [58] #00 [0000]
lspci -vnn:
lspci -vnn: 00:00.1 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:1351]
lspci -vnn: Flags: bus master, medium devsel, latency 0
lspci -vnn:
lspci -vnn: 00:00.2 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:2351]
lspci -vnn: Flags: bus master, medium devsel, latency 0
lspci -vnn:
lspci -vnn: 00:00.3 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:3351]
lspci -vnn: Flags: bus master, medium devsel, latency 0
lspci -vnn:
lspci -vnn: 00:00.4 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:4351]
lspci -vnn: Flags: bus master, medium devsel, latency 0
lspci -vnn:
lspci -vnn: 00:00.5 PIC [0800]: VIA Technologies, Inc. VT3351 I/O APIC Interrupt Controller [1106:5351] (prog-if 20)
lspci -vnn: Flags: bus master, fast devsel, latency 0
lspci -vnn:
lspci -vnn: 00:00.6 Host bridge [0600]: VIA Technologies, Inc. Unknown device [1106:6238]
lspci -vnn: Subsystem: Unknown device [0008:0000]
lspci -vnn: Flags: bus master, medium devsel, latency 0
lspci -vnn:
lspci -vnn: 00:00.7 Host bridge [0600]: VIA Technologies, Inc. VT3351 Host Bridge [1106:7351]
lspci -vnn: Flags: bus master, medium devsel, latency 0
lspci -vnn:
lspci -vnn: 00:01.0 PCI bridge [0604]: VIA Technologies, Inc. [K8T890 North / VT8237 South] PCI Bridge [1106:b999]
lspci -vnn: Flags: bus master, 66MHz, medium devsel, latency 0
lspci -vnn: Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
lspci -vnn: Capabilities: [70] Power Management version 2
lspci -vnn:
lspci -vnn: 00:02.0 PCI bridge [0604]: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller [1106:a238]
lspci -vnn: Flags: bus master, fast devsel, latency 0
lspci -vnn: Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
lspci -vnn: Memory behind bridge: f9000000-fbbfffff
lspci -vnn: Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
lspci -vnn: Capabilities: [40] Express Root Port (Slot+) IRQ 0
lspci -vnn: Capabilities: [68] Power Management version 2
lspci -vnn: Capabilities: [70] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable+
lspci -vnn:
lspci -vnn: 00:03.0 PCI bridge [0604]: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller [1106:c238]
lspci -vnn: Flags: bus master, fast devsel, latency 0
lspci -vnn: Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
lspci -vnn: I/O behind bridge: 0000d000-0000dfff
lspci -vnn: Memory behind bridge: fbd00000-fbdfffff
lspci -vnn: Capabilities: [40] Express Root Port (Slot+) IRQ 0
lspci -vnn: Capabilities: [68] Power Management version 2
lspci -vnn: Capabilities: [70] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable+
lspci -vnn:
lspci -vnn: 00:03.1 PCI bridge [0604]: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller [1106:d238]
lspci -vnn: Flags: bus master, fast devsel, latency 0
lspci -vnn: Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
lspci -vnn: Prefetchable memory behind bridge: 00000000f7f00000-00000000f7ffffff
lspci -vnn: Capabilities: [40] Express Root Port (Slot+) IRQ 0
lspci -vnn: Capabilities: [68] Power Management version 2
lspci -vnn: Capabilities: [70] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable+
lspci -vnn:
lspci -vnn: 00:03.2 PCI bridge [0604]: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller [1106:e238]
lspci -vnn: Flags: bus master, fast devsel, latency 0
lspci -vnn: Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
lspci -vnn: Memory behind bridge: fbc00000-fbcfffff
lspci -vnn: Capabilities: [40] Express Root Port (Slot+) IRQ 0
lspci -vnn: Capabilities: [68] Power Management version 2
lspci -vnn: Capabilities: [70] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable+
lspci -vnn:
lspci -vnn: 00:03.3 PCI bridge [0604]: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller [1106:f238]
lspci -vnn: Flags: bus master, fast devsel, latency 0
lspci -vnn: Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
lspci -vnn: Prefetchable memory behind bridge: 00000000f7e00000-00000000f7efffff
lspci -vnn: Capabilities: [40] Express Root Port (Slot+) IRQ 0
lspci -vnn: Capabilities: [68] Power Management version 2
lspci -vnn: Capabilities: [70] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable+
lspci -vnn:
lspci -vnn: 00:0f.0 IDE interface [0101]: VIA Technologies, Inc. VT8237A SATA 2-Port Controller [1106:0591] (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
lspci -vnn: Subsystem: VIA Technologies, Inc. VT8237A SATA 2-Port Controller [1106:0591]
lspci -vnn: Flags: bus master, medium devsel, latency 64, IRQ 82
lspci -vnn: I/O ports at cc00 [size=8]
lspci -vnn: I/O ports at c880 [size=4]
lspci -vnn: I/O ports at c800 [size=8]
lspci -vnn: I/O ports at c480 [size=4]
lspci -vnn: I/O ports at c400 [size=16]
lspci -vnn: I/O ports at c000 [size=256]
lspci -vnn: Capabilities: [c0] Power Management version 2
lspci -vnn:
lspci -vnn: 00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 07) (prog-if 8a [Master SecP PriP])
lspci -vnn: Subsystem: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571]
lspci -vnn: Flags: bus master, medium devsel, latency 32
lspci -vnn: I/O ports at fc00 [size=16]
lspci -vnn: Capabilities: [c0] Power Management version 2
lspci -vnn:
lspci -vnn: 00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0)
lspci -vnn: Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
lspci -vnn: Flags: bus master, medium devsel, latency 64, IRQ 66
lspci -vnn: I/O ports at b480 [size=32]
lspci -vnn: Capabilities: [80] Power Management version 2
lspci -vnn:
lspci -vnn: 00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0)
lspci -vnn: Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
lspci -vnn: Flags: bus master, medium devsel, latency 64, IRQ 74
lspci -vnn: I/O ports at b800 [size=32]
lspci -vnn: Capabilities: [80] Power Management version 2
lspci -vnn:
lspci -vnn: 00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0)
lspci -vnn: Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
lspci -vnn: Flags: bus master, medium devsel, latency 64, IRQ 82
lspci -vnn: I/O ports at b880 [size=32]
lspci -vnn: Capabilities: [80] Power Management version 2
lspci -vnn:
lspci -vnn: 00:10.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0)
lspci -vnn: Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
lspci -vnn: Flags: bus master, medium devsel, latency 64, IRQ 90
lspci -vnn: I/O ports at bc00 [size=32]
lspci -vnn: Capabilities: [80] Power Management version 2
lspci -vnn:
lspci -vnn: 00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 86) (prog-if 20)
lspci -vnn: Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104]
lspci -vnn: Flags: bus master, medium devsel, latency 64, IRQ 82
lspci -vnn: Memory at f8fffc00 (32-bit, non-prefetchable) [size=256]
lspci -vnn: Capabilities: [80] Power Management version 2
lspci -vnn:
lspci -vnn: 00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237A PCI to ISA Bridge [1106:3337]
lspci -vnn: Subsystem: VIA Technologies, Inc. VT8237A PCI to ISA Bridge [1106:3337]
lspci -vnn: Flags: medium devsel
lspci -vnn: Capabilities: [c0] Power Management version 2
lspci -vnn:
lspci -vnn: 00:11.7 Host bridge [0600]: VIA Technologies, Inc. VT8251 Ultra VLINK Controller [1106:287e]
lspci -vnn: Subsystem: VIA Technologies, Inc. Unknown device [1106:337e]
lspci -vnn: Flags: bus master, medium devsel, latency 128
lspci -vnn: Capabilities: [58] HyperTransport: Interrupt Discovery and Configuration
lspci -vnn:
lspci -vnn: 00:13.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237A Host Bridge [1106:337b]
lspci -vnn: Flags: bus master, fast devsel, latency 0
lspci -vnn: Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
lspci -vnn: Memory behind bridge: fbf00000-fbffffff
lspci -vnn: Capabilities: [60] HyperTransport: MSI Mapping
lspci -vnn: Capabilities: [70] Subsystem: Unknown device [f816:fb85]
lspci -vnn:
lspci -vnn: 00:13.1 PCI bridge [0604]: VIA Technologies, Inc. VT8237A PCI to PCI Bridge [1106:337a] (prog-if 01)
lspci -vnn: Flags: bus master, fast devsel, latency 0
lspci -vnn: Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
lspci -vnn: I/O behind bridge: 0000e000-0000efff
lspci -vnn: Memory behind bridge: fbe00000-fbefffff
lspci -vnn: Prefetchable memory behind bridge: 0000000088000000-00000000880fffff
lspci -vnn: Capabilities: [60] HyperTransport: MSI Mapping
lspci -vnn: Capabilities: [70] Subsystem: Unknown device [1bfb:af10]
lspci -vnn:
lspci -vnn: 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
lspci -vnn: Flags: fast devsel
lspci -vnn: Capabilities: [80] HyperTransport: Host or Secondary Interface
lspci -vnn:
lspci -vnn: 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
lspci -vnn: Flags: fast devsel
lspci -vnn:
lspci -vnn: 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
lspci -vnn: Flags: fast devsel
lspci -vnn:
lspci -vnn: 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
lspci -vnn: Flags: fast devsel
lspci -vnn:
lspci -vnn: 02:00.0 VGA compatible controller [0300]: nVidia Corporation NV44 [GeForce 6200 TurboCache(TM)] [10de:0161] (rev a1)
lspci -vnn: Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:0271]
lspci -vnn: Flags: bus master, fast devsel, latency 0, IRQ 11
lspci -vnn: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
lspci -vnn: Memory at d0000000 (64-bit, prefetchable) [size=256M]
lspci -vnn: Memory at f9000000 (64-bit, non-prefetchable) [size=16M]
lspci -vnn: Expansion ROM at fbbe0000 [disabled] [size=128K]
lspci -vnn: Capabilities: [60] Power Management version 2
lspci -vnn: Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
lspci -vnn: Capabilities: [78] Express Endpoint IRQ 0
lspci -vnn:
lspci -vnn: 04:00.0 Ethernet controller [0200]: Unknown device [1969:1048] (rev b0)
lspci -vnn: Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8226]
lspci -vnn: Flags: bus master, fast devsel, latency 0, IRQ 11
lspci -vnn: Memory at fbcc0000 (64-bit, non-prefetchable) [size=256K]
lspci -vnn: Expansion ROM at fbca0000 [disabled] [size=128K]
lspci -vnn: Capabilities: [40] Power Management version 2
lspci -vnn: Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
lspci -vnn: Capabilities: [58] Express Endpoint IRQ 0
lspci -vnn: Capabilities: [6c] Vital Product Data
lspci -vnn:
lspci -vnn: 06:00.0 SATA controller [0106]: Marvell Technology Group Ltd. Unknown device [11ab:6121] (rev b0) (prog-if 8f)
lspci -vnn: Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8212]
lspci -vnn: Flags: bus master, fast devsel, latency 0, IRQ 11
lspci -vnn: I/O ports at dc00 [size=8]
lspci -vnn: I/O ports at d880 [size=4]
lspci -vnn: I/O ports at d800 [size=8]
lspci -vnn: I/O ports at d480 [size=4]
lspci -vnn: I/O ports at d400 [size=16]
lspci -vnn: Memory at fbdffc00 (32-bit, non-prefetchable) [size=1K]
lspci -vnn: Capabilities: [48] Power Management version 2
lspci -vnn: Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
lspci -vnn: Capabilities: [e0] Express Legacy Endpoint IRQ 0
lspci -vnn:
lspci -vnn: 07:06.0 Ethernet controller [0200]: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller [100b:0020]
lspci -vnn: Subsystem: Netgear Unknown device [1385:f311]
lspci -vnn: Flags: bus master, medium devsel, latency 64, IRQ 98
lspci -vnn: I/O ports at e800 [size=256]
lspci -vnn: Memory at fbeff000 (32-bit, non-prefetchable) [size=4K]
lspci -vnn: Expansion ROM at 88000000 [disabled] [size=64K]
lspci -vnn: Capabilities: [40] Power Management version 2
lspci -vnn:
lspci -vnn: 08:01.0 Audio device [0403]: VIA Technologies, Inc. VIA High Definition Audio Controller [1106:3288] (rev 10)
lspci -vnn: Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81e7]
lspci -vnn: Flags: bus master, fast devsel, latency 0, IRQ 10
lspci -vnn: Memory at fbffc000 (64-bit, non-prefetchable) [size=16K]
lspci -vnn: Capabilities: [50] Power Management version 2
lspci -vnn: Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
lspci -vnn: Capabilities: [70] Express Unknown type IRQ 0
lspci -vnn:
modulemap: 1106:0591 sata_via
modulemap: 1106:0571 via82cxxx
modulemap: 1106:3038 uhci_hcd
modulemap: 1106:3038 uhci_hcd
modulemap: 1106:3038 uhci_hcd
modulemap: 1106:3038 uhci_hcd
modulemap: 1106:3104 ehci_hcd
modulemap: 100b:0020 natsemi
lsmod: Module Size Used by
lsmod: sd_mod 18832 0
lsmod: qnx4 10612 0
lsmod: ntfs 184084 0
lsmod: xfs 464756 0
lsmod: reiserfs 210432 0
lsmod: jfs 156380 0
lsmod: ext3 116488 3
lsmod: jbd 47272 1 ext3
lsmod: vfat 11392 0
lsmod: fat 45596 1 vfat
lsmod: natsemi 24544 0
lsmod: nls_iso8859_1 4096 2
lsmod: rsrc_nonstatic 11648 0
lsmod: pcmcia_core 35856 1 rsrc_nonstatic
lsmod: isofs 31544 0
lsmod: ide_generic 1280 0 [permanent]
lsmod: pdc202xx_new 7808 0 [permanent]
lsmod: sc1200 6528 0 [permanent]
lsmod: sis5513 12296 0 [permanent]
lsmod: opti621 3972 0 [permanent]
lsmod: amd74xx 12956 0 [permanent]
lsmod: piix 9092 0 [permanent]
lsmod: pdc202xx_old 9344 0 [permanent]
lsmod: it821x 7684 0 [permanent]
lsmod: siimage 10880 0 [permanent]
lsmod: atiixp 5776 0 [permanent]
lsmod: cy82c693 4356 0 [permanent]
lsmod: trm290 3972 0 [permanent]
lsmod: alim15x3 11020 0 [permanent]
lsmod: hpt34x 4992 0 [permanent]
lsmod: ns87415 4168 0 [permanent]
lsmod: rz1000 2688 0 [permanent]
lsmod: cs5520 4608 0 [permanent]
lsmod: serverworks 8328 0 [permanent]
lsmod: cs5535 4224 0 [permanent]
lsmod: jmicron 4096 0 [permanent]
lsmod: cs5530 4864 0 [permanent]
lsmod: triflex 3712 0 [permanent]
lsmod: slc90e66 4992 0 [permanent]
lsmod: aec62xx 6656 0 [permanent]
lsmod: cmd64x 9884 0 [permanent]
lsmod: usb_storage 70976 0
lsmod: vga16fb 11148 2
lsmod: vgastate 7680 1 vga16fb
lsmod: usbserial 28136 0
lsmod: usbhid 35552 0
lsmod: usbkbd 6656 0
lsmod: thermal 13320 0
lsmod: processor 23212 1 thermal
lsmod: fan 4740 0
lsmod: ide_cd 35360 0
lsmod: cdrom 32160 1 ide_cd
lsmod: ide_disk 14720 7
lsmod: generic 4740 0 [permanent]
lsmod: parport_pc 31268 0
lsmod: parport 31816 1 parport_pc
lsmod: floppy 51748 0
lsmod: ehci_hcd 26888 0
lsmod: sata_via 9988 0
lsmod: uhci_hcd 19980 0
lsmod: usbcore 108676 7 usb_storage,usbserial,usbhid,usbkbd,ehci_hcd,uhci_hcd
lsmod: via82cxxx 8324 0 [permanent]
lsmod: ide_core 107248 31 ide_generic,pdc202xx_new,sc1200,sis5513,opti621,amd74xx,piix,pdc202xx_old,it821x,siimage,atiixp,cy82c693,trm290,alim15x3,hpt34x,ns87415,rz1000,cs5520,serverworks,cs5535,jmicron,cs5530,triflex,slc90e66,aec62xx,cmd64x,usb_storage,ide_cd,ide_disk,generic,via82cxxx
lsmod: libata 87316 1 sata_via
lsmod: scsi_mod 121352 3 sd_mod,usb_storage,libata
df: Filesystem 1k-blocks Used Available Use% Mounted on
df: tmpfs 453392 432 452960 0% /dev
df: tmpfs 453392 432 452960 0% /dev
df: tmpfs 453392 432 452960 0% /.dev
df: /dev/ide/host0/bus0/target0/lun0/part1 6728280 2350036 4036464 37% /target
df: /dev/ide/host0/bus0/target1/lun0/part4 91815552 64389472 22762092 74% /target/bg4
df: /dev/ide/host0/bus0/target0/lun0/part6 21133524 2919344 17140640 15% /target/home
free: total used free shared buffers
free: Mem: 906784 884820 21964 0 52180
free: Swap: 5401916 428 5401488
free: Total: 6308700 885248 5423452
cardctl status: /usr/bin/report-hw: /usr/bin/report-hw: 50: cardctl: not found
cardctl ident: /usr/bin/report-hw: /usr/bin/report-hw: 51: cardctl: not found
/proc/cpuinfo: processor : 0
/proc/cpuinfo: vendor_id : AuthenticAMD
/proc/cpuinfo: cpu family : 15
/proc/cpuinfo: model : 79
/proc/cpuinfo: model name : AMD Sempron(tm) Processor 2800+
/proc/cpuinfo: stepping : 2
/proc/cpuinfo: cpu MHz : 1599.890
/proc/cpuinfo: cache size : 128 KB
/proc/cpuinfo: fdiv_bug : no
/proc/cpuinfo: hlt_bug : no
/proc/cpuinfo: f00f_bug : no
/proc/cpuinfo: coma_bug : no
/proc/cpuinfo: fpu : yes
/proc/cpuinfo: fpu_exception : yes
/proc/cpuinfo: cpuid level : 1
/proc/cpuinfo: wp : yes
/proc/cpuinfo: flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext fxsr_opt lm 3dnowext 3dnow pni cx16 lahf_lm cr8legacy ts ttp tm stc
/proc/cpuinfo: bogomips : 3201.70
/proc/cpuinfo:
/proc/ioports: 0000-001f : dma1
/proc/ioports: 0020-0021 : pic1
/proc/ioports: 0040-0043 : timer0
/proc/ioports: 0050-0053 : timer1
/proc/ioports: 0060-006f : keyboard
/proc/ioports: 0080-008f : dma page reg
/proc/ioports: 00a0-00a1 : pic2
/proc/ioports: 00c0-00df : dma2
/proc/ioports: 00f0-00ff : fpu
/proc/ioports: 0170-0177 : ide1
/proc/ioports: 01f0-01f7 : ide0
/proc/ioports: 0376-0376 : ide1
/proc/ioports: 0378-037a : parport0
/proc/ioports: 037b-037f : parport0
/proc/ioports: 03c0-03df : vga+
/proc/ioports: 03f2-03f5 : floppy
/proc/ioports: 03f6-03f6 : ide0
/proc/ioports: 03f7-03f7 : floppy DIR
/proc/ioports: 03f8-03ff : serial
/proc/ioports: 0800-0803 : ACPI PM1a_EVT_BLK
/proc/ioports: 0804-0805 : ACPI PM1a_CNT_BLK
/proc/ioports: 0808-080b : ACPI PM_TMR
/proc/ioports: 0810-0815 : ACPI CPU throttle
/proc/ioports: 0820-0823 : ACPI GPE0_BLK
/proc/ioports: 0a20-0a2f : pnp 00:07
/proc/ioports: 0a30-0a3f : pnp 00:07
/proc/ioports: 0c00-0c0f : pnp 00:07
/proc/ioports: 0cf8-0cff : PCI conf1
/proc/ioports: 0d00-0d0f : pnp 00:07
/proc/ioports: b480-b49f : 0000:00:10.0
/proc/ioports: b480-b49f : uhci_hcd
/proc/ioports: b800-b81f : 0000:00:10.1
/proc/ioports: b800-b81f : uhci_hcd
/proc/ioports: b880-b89f : 0000:00:10.2
/proc/ioports: b880-b89f : uhci_hcd
/proc/ioports: bc00-bc1f : 0000:00:10.3
/proc/ioports: bc00-bc1f : uhci_hcd
/proc/ioports: c000-c0ff : 0000:00:0f.0
/proc/ioports: c000-c0ff : sata_via
/proc/ioports: c400-c40f : 0000:00:0f.0
/proc/ioports: c400-c40f : sata_via
/proc/ioports: c480-c483 : 0000:00:0f.0
/proc/ioports: c480-c483 : sata_via
/proc/ioports: c800-c807 : 0000:00:0f.0
/proc/ioports: c800-c807 : sata_via
/proc/ioports: c880-c883 : 0000:00:0f.0
/proc/ioports: c880-c883 : sata_via
/proc/ioports: cc00-cc07 : 0000:00:0f.0
/proc/ioports: cc00-cc07 : sata_via
/proc/ioports: d000-dfff : PCI Bus #06
/proc/ioports: d400-d40f : 0000:06:00.0
/proc/ioports: d480-d483 : 0000:06:00.0
/proc/ioports: d800-d807 : 0000:06:00.0
/proc/ioports: d880-d883 : 0000:06:00.0
/proc/ioports: dc00-dc07 : 0000:06:00.0
/proc/ioports: e000-efff : PCI Bus #07
/proc/ioports: e800-e8ff : 0000:07:06.0
/proc/ioports: e800-e8ff : natsemi
/proc/ioports: fc00-fc0f : 0000:00:0f.1
/proc/ioports: fc00-fc07 : ide0
/proc/ioports: fc08-fc0f : ide1
/proc/iomem: 00000000-0009dbff : System RAM
/proc/iomem: 00000000-00000000 : Crash kernel
/proc/iomem: 0009dc00-0009ffff : reserved
/proc/iomem: 000a0000-000bffff : Video RAM area
/proc/iomem: 000c0000-000cedff : Video ROM
/proc/iomem: 000f0000-000fffff : System ROM
/proc/iomem: 00100000-7ffaffff : System RAM
/proc/iomem: 00100000-00276ef8 : Kernel code
/proc/iomem: 00276ef9-0030cc73 : Kernel data
/proc/iomem: 7ffb0000-7ffbdfff : ACPI Tables
/proc/iomem: 7ffbe000-7ffdffff : ACPI Non-volatile Storage
/proc/iomem: 7ffe0000-7fffffff : reserved
/proc/iomem: 88000000-880fffff : PCI Bus #07
/proc/iomem: 88000000-8800ffff : 0000:07:06.0
/proc/iomem: d0000000-dfffffff : PCI Bus #02
/proc/iomem: d0000000-dfffffff : 0000:02:00.0
/proc/iomem: f7e00000-f7efffff : PCI Bus #03
/proc/iomem: f7f00000-f7ffffff : PCI Bus #05
/proc/iomem: f8fffc00-f8fffcff : 0000:00:10.4
/proc/iomem: f8fffc00-f8fffcff : ehci_hcd
/proc/iomem: f9000000-fbbfffff : PCI Bus #02
/proc/iomem: f9000000-f9ffffff : 0000:02:00.0
/proc/iomem: fa000000-faffffff : 0000:02:00.0
/proc/iomem: fbbe0000-fbbfffff : 0000:02:00.0
/proc/iomem: fbc00000-fbcfffff : PCI Bus #04
/proc/iomem: fbca0000-fbcbffff : 0000:04:00.0
/proc/iomem: fbcc0000-fbcfffff : 0000:04:00.0
/proc/iomem: fbd00000-fbdfffff : PCI Bus #06
/proc/iomem: fbdffc00-fbdfffff : 0000:06:00.0
/proc/iomem: fbe00000-fbefffff : PCI Bus #07
/proc/iomem: fbeff000-fbefffff : 0000:07:06.0
/proc/iomem: fbeff000-fbefffff : natsemi
/proc/iomem: fbf00000-fbffffff : PCI Bus #08
/proc/iomem: fbffc000-fbffffff : 0000:08:01.0
/proc/iomem: fec00000-fec00fff : reserved
/proc/iomem: fecc0000-fecc0fff : reserved
/proc/iomem: ff780000-ffffffff : reserved
/proc/interrupts: CPU0
/proc/interrupts: 0: 838283 IO-APIC-edge timer
/proc/interrupts: 1: 745 IO-APIC-edge i8042
/proc/interrupts: 6: 8 IO-APIC-edge floppy
/proc/interrupts: 7: 0 IO-APIC-edge parport0
/proc/interrupts: 9: 0 IO-APIC-level acpi
/proc/interrupts: 14: 116996 IO-APIC-edge ide0
/proc/interrupts: 15: 2935 IO-APIC-edge ide1
/proc/interrupts: 66: 0 IO-APIC-level uhci_hcd:usb1
/proc/interrupts: 74: 24 IO-APIC-level uhci_hcd:usb2
/proc/interrupts: 82: 23 IO-APIC-level uhci_hcd:usb3, libata, ehci_hcd:usb5
/proc/interrupts: 90: 0 IO-APIC-level uhci_hcd:usb4
/proc/interrupts: 98: 520322 IO-APIC-level eth0
/proc/interrupts: NMI: 0
/proc/interrupts: LOC: 838279
/proc/interrupts: ERR: 0
/proc/interrupts: MIS: 0
/proc/meminfo: MemTotal: 906784 kB
/proc/meminfo: MemFree: 21884 kB
/proc/meminfo: Buffers: 52180 kB
/proc/meminfo: Cached: 760044 kB
/proc/meminfo: SwapCached: 0 kB
/proc/meminfo: Active: 371088 kB
/proc/meminfo: Inactive: 459548 kB
/proc/meminfo: HighTotal: 0 kB
/proc/meminfo: HighFree: 0 kB
/proc/meminfo: LowTotal: 906784 kB
/proc/meminfo: LowFree: 21884 kB
/proc/meminfo: SwapTotal: 5401916 kB
/proc/meminfo: SwapFree: 5401488 kB
/proc/meminfo: Dirty: 1192 kB
/proc/meminfo: Writeback: 0 kB
/proc/meminfo: AnonPages: 18284 kB
/proc/meminfo: Mapped: 1716 kB
/proc/meminfo: Slab: 42908 kB
/proc/meminfo: PageTables: 220 kB
/proc/meminfo: NFS_Unstable: 0 kB
/proc/meminfo: Bounce: 0 kB
/proc/meminfo: CommitLimit: 5855308 kB
/proc/meminfo: Committed_AS: 22012 kB
/proc/meminfo: VmallocTotal: 122576 kB
/proc/meminfo: VmallocUsed: 9844 kB
/proc/meminfo: VmallocChunk: 112312 kB
/proc/bus/input/devices: I: Bus=0011 Vendor=0001 Product=0001 Version=ab41
/proc/bus/input/devices: N: Name="AT Translated Set 2 keyboard"
/proc/bus/input/devices: P: Phys=isa0060/serio0/input0
/proc/bus/input/devices: S: Sysfs=/class/input/input0
/proc/bus/input/devices: H: Handlers=kbd
/proc/bus/input/devices: B: EV=120013
/proc/bus/input/devices: B: KEY=4 2000000 3802078 f840d001 feffffdf ffefffff ffffffff fffffffe
/proc/bus/input/devices: B: MSC=10
/proc/bus/input/devices: B: LED=7
/proc/bus/input/devices:
dmidecode: # dmidecode 2.8
dmidecode: SMBIOS 2.4 present.
dmidecode: 54 structures occupying 2032 bytes.
dmidecode: Table at 0x000F0750.
dmidecode:
dmidecode: Handle 0x0000, DMI type 0, 24 bytes
dmidecode: BIOS Information
dmidecode: Vendor: American Megatrends Inc.
dmidecode: Version: 0504
dmidecode: Release Date: 08/08/2006
dmidecode: Address: 0xF0000
dmidecode: Runtime Size: 64 kB
dmidecode: ROM Size: 2048 kB
dmidecode: Characteristics:
dmidecode: ISA is supported
dmidecode: PCI is supported
dmidecode: PNP is supported
dmidecode: APM is supported
dmidecode: BIOS is upgradeable
dmidecode: BIOS shadowing is allowed
dmidecode: ESCD support is available
dmidecode: Boot from CD is supported
dmidecode: Selectable boot is supported
dmidecode: BIOS ROM is socketed
dmidecode: EDD is supported
dmidecode: 5.25"/1.2 MB floppy services are supported (int 13h)
dmidecode: 3.5"/720 KB floppy services are supported (int 13h)
dmidecode: 3.5"/2.88 MB floppy services are supported (int 13h)
dmidecode: Print screen service is supported (int 5h)
dmidecode: 8042 keyboard services are supported (int 9h)
dmidecode: Serial services are supported (int 14h)
dmidecode: Printer services are supported (int 17h)
dmidecode: CGA/mono video services are supported (int 10h)
dmidecode: ACPI is supported
dmidecode: USB legacy is supported
dmidecode: LS-120 boot is supported
dmidecode: ATAPI Zip drive boot is supported
dmidecode: BIOS boot specification is supported
dmidecode: BIOS Revision: 8.12
dmidecode:
dmidecode: Handle 0x0001, DMI type 1, 27 bytes
dmidecode: System Information
dmidecode: Manufacturer: System manufacturer
dmidecode: Product Name: System Product Name
dmidecode: Version: System Version
dmidecode: Serial Number: System Serial Number
dmidecode: UUID: 1CF75E7A-74FE-D511-81CF-E00250CC0F1E
dmidecode: Wake-up Type: Power Switch
dmidecode: SKU Number: To Be Filled By O.E.M.
dmidecode: Family: To Be Filled By O.E.M.
dmidecode:
dmidecode: Handle 0x0002, DMI type 2, 15 bytes
dmidecode: Base Board Information
dmidecode: Manufacturer: ASUSTeK Computer INC.
dmidecode: Product Name: M2V
dmidecode: Version: Rev 1.xx
dmidecode: Serial Number: MB-1234567890
dmidecode: Asset Tag: To Be Filled By O.E.M.
dmidecode: Features:
dmidecode: Board is a hosting board
dmidecode: Board is replaceable
dmidecode: Location In Chassis: To Be Filled By O.E.M.
dmidecode: Chassis Handle: 0x0003
dmidecode: Type: Motherboard
dmidecode: Contained Object Handles: 0
dmidecode:
dmidecode: Handle 0x0003, DMI type 3, 21 bytes
dmidecode: Chassis Information
dmidecode: Manufacturer: Chassis Manufacture
dmidecode: Type: Desktop
dmidecode: Lock: Not Present
dmidecode: Version: Chassis Version
dmidecode: Serial Number: Chassis Serial Number
dmidecode: Asset Tag: Asset-1234567890
dmidecode: Boot-up State: Safe
dmidecode: Power Supply State: Safe
dmidecode: Thermal State: Safe
dmidecode: Security Status: None
dmidecode: OEM Information: 0x00000001
dmidecode: Heigth: Unspecified
dmidecode: Number Of Power Cords: 1
dmidecode: Contained Elements: 0
dmidecode:
dmidecode: Handle 0x0004, DMI type 4, 35 bytes
dmidecode: Processor Information
dmidecode: Socket Designation: SOCKET AM2
dmidecode: Type: Central Processor
dmidecode: Family: Athlon 64
dmidecode: Manufacturer: AMD
dmidecode: ID: F2 0F 04 00 FF FB 8B 07
dmidecode: Signature: Extended Family 0, Extended Model 4, Stepping 2
dmidecode: Flags:
dmidecode: FPU (Floating-point unit on-chip)
dmidecode: VME (Virtual mode extension)
dmidecode: DE (Debugging extension)
dmidecode: PSE (Page size extension)
dmidecode: TSC (Time stamp counter)
dmidecode: MSR (Model specific registers)
dmidecode: PAE (Physical address extension)
dmidecode: MCE (Machine check exception)
dmidecode: CX8 (CMPXCHG8 instruction supported)
dmidecode: APIC (On-chip APIC hardware supported)
dmidecode: SEP (Fast system call)
dmidecode: MTRR (Memory type range registers)
dmidecode: PGE (Page global enable)
dmidecode: MCA (Machine check architecture)
dmidecode: CMOV (Conditional move instruction supported)
dmidecode: PAT (Page attribute table)
dmidecode: PSE-36 (36-bit page size extension)
dmidecode: CLFSH (CLFLUSH instruction supported)
dmidecode: MMX (MMX technology supported)
dmidecode: FXSR (Fast floating-point save and restore)
dmidecode: SSE (Streaming SIMD extensions)
dmidecode: SSE2 (Streaming SIMD extensions 2)
dmidecode: Version: AMD Sempron(tm) Processor 2800+
dmidecode: Voltage: 1.5 V
dmidecode: External Clock: 200 MHz
dmidecode: Max Speed: 3000 MHz
dmidecode: Current Speed: 1600 MHz
dmidecode: Status: Populated, Enabled
dmidecode: Upgrade: <OUT OF SPEC>
dmidecode: L1 Cache Handle: 0x0005
dmidecode: L2 Cache Handle: 0x0006
dmidecode: L3 Cache Handle: 0x0007
dmidecode: Serial Number: To Be Filled By O.E.M.
dmidecode: Asset Tag: To Be Filled By O.E.M.
dmidecode: Part Number: To Be Filled By O.E.M.
dmidecode:
dmidecode: Handle 0x0005, DMI type 7, 19 bytes
dmidecode: Cache Information
dmidecode: Socket Designation: L1-Cache
dmidecode: Configuration: Enabled, Not Socketed, Level 1
dmidecode: Operational Mode: Varies With Memory Address
dmidecode: Location: Internal
dmidecode: Installed Size: 64 KB
dmidecode: Maximum Size: 64 KB
dmidecode: Supported SRAM Types:
dmidecode: Pipeline Burst
dmidecode: Installed SRAM Type: Pipeline Burst
dmidecode: Speed: Unknown
dmidecode: Error Correction Type: Single-bit ECC
dmidecode: System Type: Data
dmidecode: Associativity: 4-way Set-associative
dmidecode:
dmidecode: Handle 0x0006, DMI type 7, 19 bytes
dmidecode: Cache Information
dmidecode: Socket Designation: L2-Cache
dmidecode: Configuration: Enabled, Not Socketed, Level 2
dmidecode: Operational Mode: Varies With Memory Address
dmidecode: Location: Internal
dmidecode: Installed Size: 128 KB
dmidecode: Maximum Size: 128 KB
dmidecode: Supported SRAM Types:
dmidecode: Pipeline Burst
dmidecode: Installed SRAM Type: Pipeline Burst
dmidecode: Speed: Unknown
dmidecode: Error Correction Type: Single-bit ECC
dmidecode: System Type: Unified
dmidecode: Associativity: 4-way Set-associative
dmidecode:
dmidecode: Handle 0x0007, DMI type 7, 19 bytes
dmidecode: Cache Information
dmidecode: Socket Designation: L3-Cache
dmidecode: Configuration: Disabled, Not Socketed, Level 3
dmidecode: Operational Mode: Unknown
dmidecode: Location: Internal
dmidecode: Installed Size: 0 KB
dmidecode: Maximum Size: 0 KB
dmidecode: Supported SRAM Types:
dmidecode: Unknown
dmidecode: Installed SRAM Type: Unknown
dmidecode: Speed: Unknown
dmidecode: Error Correction Type: Unknown
dmidecode: System Type: Unknown
dmidecode: Associativity: Unknown
dmidecode:
dmidecode: Handle 0x0008, DMI type 6, 12 bytes
dmidecode: Memory Module Information
dmidecode: Socket Designation: DIMM0
dmidecode: Bank Connections: 6 1
dmidecode: Current Speed: 37 ns
dmidecode: Type: ECC DIMM
dmidecode: Installed Size: 1024 MB (Double-bank Connection)
dmidecode: Enabled Size: 1024 MB (Double-bank Connection)
dmidecode: Error Status: OK
dmidecode:
dmidecode: Handle 0x0009, DMI type 6, 12 bytes
dmidecode: Memory Module Information
dmidecode: Socket Designation: DIMM1
dmidecode: Bank Connections: 6 1
dmidecode: Current Speed: 37 ns
dmidecode: Type: ECC DIMM
dmidecode: Installed Size: 1024 MB (Double-bank Connection)
dmidecode: Enabled Size: 1024 MB (Double-bank Connection)
dmidecode: Error Status: OK
dmidecode:
dmidecode: Handle 0x000A, DMI type 6, 12 bytes
dmidecode: Memory Module Information
dmidecode: Socket Designation: DIMM2
dmidecode: Bank Connections: None
dmidecode: Current Speed: Unknown
dmidecode: Type: Unknown
dmidecode: Installed Size: Not Installed
dmidecode: Enabled Size: Not Installed
dmidecode: Error Status: OK
dmidecode:
dmidecode: Handle 0x000B, DMI type 6, 12 bytes
dmidecode: Memory Module Information
dmidecode: Socket Designation: DIMM3
dmidecode: Bank Connections: None
dmidecode: Current Speed: Unknown
dmidecode: Type: Unknown
dmidecode: Installed Size: Not Installed
dmidecode: Enabled Size: Not Installed
dmidecode: Error Status: OK
dmidecode:
dmidecode: Handle 0x000C, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: PS/2 Mouse
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: PS2Mouse
dmidecode: External Connector Type: PS/2
dmidecode: Port Type: Mouse Port
dmidecode:
dmidecode: Handle 0x000D, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: PS/2 Keyboard
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: Keyboard
dmidecode: External Connector Type: PS/2
dmidecode: Port Type: Keyboard Port
dmidecode:
dmidecode: Handle 0x000E, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: USB1
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: USB1
dmidecode: External Connector Type: Access Bus (USB)
dmidecode: Port Type: USB
dmidecode:
dmidecode: Handle 0x000F, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: USB2
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: USB2
dmidecode: External Connector Type: Access Bus (USB)
dmidecode: Port Type: USB
dmidecode:
dmidecode: Handle 0x0010, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: USB3
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: USB3
dmidecode: External Connector Type: Access Bus (USB)
dmidecode: Port Type: USB
dmidecode:
dmidecode: Handle 0x0011, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: USB4
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: USB4
dmidecode: External Connector Type: Access Bus (USB)
dmidecode: Port Type: USB
dmidecode:
dmidecode: Handle 0x0012, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: LPT1
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: LPT1
dmidecode: External Connector Type: DB-25 female
dmidecode: Port Type: Parallel Port ECP/EPP
dmidecode:
dmidecode: Handle 0x0013, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: Audio Line_Out
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: Audio Line_Out
dmidecode: External Connector Type: Mini Jack (headphones)
dmidecode: Port Type: Audio Port
dmidecode:
dmidecode: Handle 0x0014, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: Audio Line_In
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: Audio Line_In
dmidecode: External Connector Type: Mini Jack (headphones)
dmidecode: Port Type: Audio Port
dmidecode:
dmidecode: Handle 0x0015, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: Audio Mic_In
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: Audio Mic_In
dmidecode: External Connector Type: Mini Jack (headphones)
dmidecode: Port Type: Audio Port
dmidecode:
dmidecode: Handle 0x0016, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: LAN1
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: LAN1
dmidecode: External Connector Type: RJ-45
dmidecode: Port Type: Network Port
dmidecode:
dmidecode: Handle 0x0017, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: PRI IDE
dmidecode: Internal Connector Type: On Board IDE
dmidecode: External Reference Designator: Not Specified
dmidecode: External Connector Type: None
dmidecode: Port Type: Other
dmidecode:
dmidecode: Handle 0x0018, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: SEC IDE
dmidecode: Internal Connector Type: On Board IDE
dmidecode: External Reference Designator: Not Specified
dmidecode: External Connector Type: None
dmidecode: Port Type: Other
dmidecode:
dmidecode: Handle 0x0019, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: SB_SATA1
dmidecode: Internal Connector Type: On Board IDE
dmidecode: External Reference Designator: Not Specified
dmidecode: External Connector Type: None
dmidecode: Port Type: Other
dmidecode:
dmidecode: Handle 0x001A, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: SB_SATA2
dmidecode: Internal Connector Type: On Board IDE
dmidecode: External Reference Designator: Not Specified
dmidecode: External Connector Type: None
dmidecode: Port Type: Other
dmidecode:
dmidecode: Handle 0x001B, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: FLOPPY
dmidecode: Internal Connector Type: On Board Floppy
dmidecode: External Reference Designator: Not Specified
dmidecode: External Connector Type: None
dmidecode: Port Type: Other
dmidecode:
dmidecode: Handle 0x001C, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: USB5
dmidecode: Internal Connector Type: Access Bus (USB)
dmidecode: External Reference Designator: Not Specified
dmidecode: External Connector Type: None
dmidecode: Port Type: USB
dmidecode:
dmidecode: Handle 0x001D, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: USB6
dmidecode: Internal Connector Type: Access Bus (USB)
dmidecode: External Reference Designator: Not Specified
dmidecode: External Connector Type: None
dmidecode: Port Type: USB
dmidecode:
dmidecode: Handle 0x001E, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: USB7
dmidecode: Internal Connector Type: Access Bus (USB)
dmidecode: External Reference Designator: Not Specified
dmidecode: External Connector Type: None
dmidecode: Port Type: USB
dmidecode:
dmidecode: Handle 0x001F, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: USB8
dmidecode: Internal Connector Type: Access Bus (USB)
dmidecode: External Reference Designator: Not Specified
dmidecode: External Connector Type: None
dmidecode: Port Type: USB
dmidecode:
dmidecode: Handle 0x0020, DMI type 9, 13 bytes
dmidecode: System Slot Information
dmidecode: Designation: PCIEx1
dmidecode: Type: 32-bit PCI Express
dmidecode: Current Usage: Available
dmidecode: Length: Long
dmidecode: Characteristics:
dmidecode: 3.3 V is provided
dmidecode: Opening is shared
dmidecode: PME signal is supported
dmidecode:
dmidecode: Handle 0x0021, DMI type 9, 13 bytes
dmidecode: System Slot Information
dmidecode: Designation: PCIEx16
dmidecode: Type: 32-bit PCI Express
dmidecode: Current Usage: In Use
dmidecode: Length: Long
dmidecode: Characteristics:
dmidecode: 3.3 V is provided
dmidecode: Opening is shared
dmidecode: PME signal is supported
dmidecode:
dmidecode: Handle 0x0022, DMI type 9, 13 bytes
dmidecode: System Slot Information
dmidecode: Designation: PCI1
dmidecode: Type: 32-bit PCI
dmidecode: Current Usage: In Use
dmidecode: Length: Short
dmidecode: ID: 1
dmidecode: Characteristics:
dmidecode: 3.3 V is provided
dmidecode: Opening is shared
dmidecode: PME signal is supported
dmidecode:
dmidecode: Handle 0x0023, DMI type 9, 13 bytes
dmidecode: System Slot Information
dmidecode: Designation: PCI2
dmidecode: Type: 32-bit PCI
dmidecode: Current Usage: Available
dmidecode: Length: Short
dmidecode: ID: 2
dmidecode: Characteristics:
dmidecode: 3.3 V is provided
dmidecode: Opening is shared
dmidecode: PME signal is supported
dmidecode:
dmidecode: Handle 0x0024, DMI type 9, 13 bytes
dmidecode: System Slot Information
dmidecode: Designation: PCI3
dmidecode: Type: 32-bit PCI
dmidecode: Current Usage: Available
dmidecode: Length: Short
dmidecode: ID: 3
dmidecode: Characteristics:
dmidecode: 3.3 V is provided
dmidecode: Opening is shared
dmidecode: PME signal is supported
dmidecode:
dmidecode: Handle 0x0025, DMI type 9, 13 bytes
dmidecode: System Slot Information
dmidecode: Designation: PCI4
dmidecode: Type: 32-bit PCI
dmidecode: Current Usage: Available
dmidecode: Length: Short
dmidecode: ID: 4
dmidecode: Characteristics:
dmidecode: 3.3 V is provided
dmidecode: Opening is shared
dmidecode: PME signal is supported
dmidecode:
dmidecode: Handle 0x0026, DMI type 10, 6 bytes
dmidecode: On Board Device Information
dmidecode: Type: Video
dmidecode: Status: Enabled
dmidecode: Description: To Be Filled By O.E.M.
dmidecode:
dmidecode: Handle 0x0027, DMI type 11, 5 bytes
dmidecode: OEM Strings
dmidecode: String 1: To Be Filled By O.E.M.
dmidecode: String 2: To Be Filled By O.E.M.
dmidecode: String 3: To Be Filled By O.E.M.
dmidecode: String 4: To Be Filled By O.E.M.
dmidecode:
dmidecode: Handle 0x0028, DMI type 13, 22 bytes
dmidecode: BIOS Language Information
dmidecode: Installable Languages: 1
dmidecode: en|US|iso8859-1
dmidecode: Currently Installed Language: en|US|iso8859-1
dmidecode:
dmidecode: Handle 0x0029, DMI type 15, 35 bytes
dmidecode: System Event Log
dmidecode: Area Length: 4 bytes
dmidecode: Header Start Offset: 0x0000
dmidecode: Header Length: 2 bytes
dmidecode: Data Start Offset: 0x0002
dmidecode: Access Method: Indexed I/O, one 16-bit index port, one 8-bit data port
dmidecode: Access Address: Index 0x046A, Data 0x046C
dmidecode: Status: Invalid, Not Full
dmidecode: Change Token: 0x00000000
dmidecode: Header Format: No Header
dmidecode: Supported Log Type Descriptors: 6
dmidecode: Descriptor 1: End of log
dmidecode: Data Format 1: OEM-specific
dmidecode: Descriptor 2: End of log
dmidecode: Data Format 2: OEM-specific
dmidecode: Descriptor 3: End of log
dmidecode: Data Format 3: OEM-specific
dmidecode: Descriptor 4: End of log
dmidecode: Data Format 4: OEM-specific
dmidecode: Descriptor 5: End of log
dmidecode: Data Format 5: OEM-specific
dmidecode: Descriptor 6: End of log
dmidecode: Data Format 6: OEM-specific
dmidecode:
dmidecode: Handle 0x002A, DMI type 16, 15 bytes
dmidecode: Physical Memory Array
dmidecode: Location: System Board Or Motherboard
dmidecode: Use: System Memory
dmidecode: Error Correction Type: None
dmidecode: Maximum Capacity: 8 GB
dmidecode: Error Information Handle: Not Provided
dmidecode: Number Of Devices: 4
dmidecode:
dmidecode: Handle 0x002B, DMI type 19, 15 bytes
dmidecode: Memory Array Mapped Address
dmidecode: Starting Address: 0x00000000000
dmidecode: Ending Address: 0x0007FFFFFFF
dmidecode: Range Size: 2 GB
dmidecode: Physical Array Handle: 0x002A
dmidecode: Partition Width: 0
dmidecode:
dmidecode: Handle 0x002C, DMI type 17, 27 bytes
dmidecode: Memory Device
dmidecode: Array Handle: 0x002A
dmidecode: Error Information Handle: Not Provided
dmidecode: Total Width: 64 bits
dmidecode: Data Width: 72 bits
dmidecode: Size: 1024 MB
dmidecode: Form Factor: DIMM
dmidecode: Set: None
dmidecode: Locator: DIMM0
dmidecode: Bank Locator: BANK0
dmidecode: Type: DDR2
dmidecode: Type Detail: Synchronous
dmidecode: Speed: 266 MHz (3.8 ns)
dmidecode: Manufacturer: Manufacturer0
dmidecode: Serial Number: SerNum0
dmidecode: Asset Tag: AssetTagNum0
dmidecode: Part Number: PartNum0
dmidecode:
dmidecode: Handle 0x002D, DMI type 20, 19 bytes
dmidecode: Memory Device Mapped Address
dmidecode: Starting Address: 0x00000000000
dmidecode: Ending Address: 0x0003FFFFFFF
dmidecode: Range Size: 1 GB
dmidecode: Physical Device Handle: 0x002C
dmidecode: Memory Array Mapped Address Handle: 0x002B
dmidecode: Partition Row Position: 1
dmidecode:
dmidecode: Handle 0x002E, DMI type 17, 27 bytes
dmidecode: Memory Device
dmidecode: Array Handle: 0x002A
dmidecode: Error Information Handle: Not Provided
dmidecode: Total Width: 64 bits
dmidecode: Data Width: 72 bits
dmidecode: Size: 1024 MB
dmidecode: Form Factor: DIMM
dmidecode: Set: None
dmidecode: Locator: DIMM1
dmidecode: Bank Locator: BANK1
dmidecode: Type: DDR2
dmidecode: Type Detail: Synchronous
dmidecode: Speed: 266 MHz (3.8 ns)
dmidecode: Manufacturer: Manufacturer1
dmidecode: Serial Number: SerNum1
dmidecode: Asset Tag: AssetTagNum1
dmidecode: Part Number: PartNum1
dmidecode:
dmidecode: Handle 0x002F, DMI type 20, 19 bytes
dmidecode: Memory Device Mapped Address
dmidecode: Starting Address: 0x00040000000
dmidecode: Ending Address: 0x0007FFFFFFF
dmidecode: Range Size: 1 GB
dmidecode: Physical Device Handle: 0x002E
dmidecode: Memory Array Mapped Address Handle: 0x002B
dmidecode: Partition Row Position: 1
dmidecode:
dmidecode: Handle 0x0030, DMI type 17, 27 bytes
dmidecode: Memory Device
dmidecode: Array Handle: 0x002A
dmidecode: Error Information Handle: Not Provided
dmidecode: Total Width: Unknown
dmidecode: Data Width: Unknown
dmidecode: Size: No Module Installed
dmidecode: Form Factor: DIMM
dmidecode: Set: None
dmidecode: Locator: DIMM2
dmidecode: Bank Locator: BANK2
dmidecode: Type: Unknown
dmidecode: Type Detail: Unknown
dmidecode: Speed: Unknown
dmidecode: Manufacturer: Manufacturer2
dmidecode: Serial Number: SerNum2
dmidecode: Asset Tag: AssetTagNum2
dmidecode: Part Number: PartNum2
dmidecode:
dmidecode: Handle 0x0031, DMI type 126, 19 bytes
dmidecode: Inactive
dmidecode:
dmidecode: Handle 0x0032, DMI type 17, 27 bytes
dmidecode: Memory Device
dmidecode: Array Handle: 0x002A
dmidecode: Error Information Handle: Not Provided
dmidecode: Total Width: Unknown
dmidecode: Data Width: Unknown
dmidecode: Size: No Module Installed
dmidecode: Form Factor: DIMM
dmidecode: Set: None
dmidecode: Locator: DIMM3
dmidecode: Bank Locator: BANK3
dmidecode: Type: Unknown
dmidecode: Type Detail: Unknown
dmidecode: Speed: Unknown
dmidecode: Manufacturer: Manufacturer3
dmidecode: Serial Number: SerNum3
dmidecode: Asset Tag: AssetTagNum3
dmidecode: Part Number: PartNum3
dmidecode:
dmidecode: Handle 0x0033, DMI type 126, 19 bytes
dmidecode: Inactive
dmidecode:
dmidecode: Handle 0x0034, DMI type 32, 20 bytes
dmidecode: System Boot Information
dmidecode: Status: No errors detected
dmidecode:
dmidecode: Handle 0x0035, DMI type 127, 4 bytes
dmidecode: End Of Table
dmidecode:
==============================================
Installer status:
==============================================
Package: preseed-common
Status: install ok unpacked
Version: 1.28
Depends: cdebconf-udeb, di-utils (>= 1.14)
Description: common files for preseeding
Package: udpkg
Status: install ok unpacked
Version: 1.04
Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.41)
Description: tiny dpkg clone
Package: localechooser
Status: install ok installed
Version: 1.37
Depends: cdebconf-udeb, iso-3166-udeb, di-utils (>= 1.15)
Description: choose language/country/locale
Installer-Menu-Item: 10
Package: acpi-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: acpi-modules
Depends: kernel-image-2.6.18-6-486-di
Description: ACPI support modules
Package: libnss-dns-udeb
Status: install ok unpacked
Version: 2.3.6.ds1-13etch5
Description: GNU C Library: NSS helper for DNS - udeb
Package: usb-serial-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: usb-serial-modules
Depends: kernel-image-2.6.18-6-486-di, usb-modules-2.6.18-6-486-di
Description: USB serial drivers
Package: cdrom-checker
Status: install ok unpacked
Version: 1.11
Depends: cdrom-detect, cdebconf-udeb (>= 0.31)
Description: Verify the cd contents
Installer-Menu-Item: 940
Package: sata-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: sata-modules
Depends: kernel-image-2.6.18-6-486-di, scsi-core-modules-2.6.18-6-486-di
Description: SATA drivers
Package: lowmemcheck
Status: install ok unpacked
Version: 1.25
Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03)
Description: detect low-memory systems and enter lowmem mode
Package: cdrom-retriever
Status: install ok installed
Version: 1.14
Provides: retriever
Depends: cdebconf-udeb, cdrom-detect
Description: Fetch modules from a CDROM
Package: main-menu
Status: install ok unpacked
Version: 1.18
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.50), cdebconf-udeb
Description: Debian installer main menu
Package: di-utils-shell
Status: install ok unpacked
Version: 1.45etch1
Depends: cdebconf-udeb, di-utils (>= 1.18)
Description: Execute a shell
Installer-Menu-Item: 950
Package: cdrom-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: cdrom-modules
Depends: ide-modules-2.6.18-6-486-di, cdrom-core-modules-2.6.18-6-486-di, kernel-image-2.6.18-6-486-di
Description: Esoteric CDROM drivers
Package: di-utils
Status: install ok installed
Version: 1.45etch1
Depends: libc6 (>= 2.3.6-6), libdebian-installer4-udeb (>= 0.50), cdebconf-udeb
Description: Miscellaneous utilities for the debian installer
Package: serial-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: serial-modules
Depends: kernel-image-2.6.18-6-486-di, pcmcia-modules-2.6.18-6-486-di
Description: Serial drivers
Package: ide-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: ide-modules
Depends: kernel-image-2.6.18-6-486-di, ide-core-modules-2.6.18-6-486-di
Description: IDE drivers
Package: cdebconf-newt-udeb
Status: install ok unpacked
Version: 0.114etch1
Depends: cdebconf-udeb, di-utils-terminfo, libc6 (>= 2.3.6-6), libnewt0.52
Description: Newt frontend for Debian Configuration Management System
Package: input-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: input-modules
Depends: kernel-image-2.6.18-6-486-di, usb-modules-2.6.18-6-486-di
Description: Input devices support
Package: module-init-tools-udeb
Status: install ok unpacked
Version: 3.3-pre4-2
Depends: libc6 (>= 2.3.6-6)
Description: tools for managing Linux kernel modules
Package: rootskel
Status: install ok installed
Version: 1.50+b1
Depends: di-utils (>= 1.43), cdebconf-udeb
Description: Skeleton root filesystem used by debian-installer
Package: udev-udeb
Status: install ok unpacked
Version: 0.105-4
Depends: libc6 (>= 2.3.6-6)
Description: /dev/ and hotplug management daemon
Package: brltty-udeb
Status: install ok unpacked
Version: 3.7.2-7.1
Depends: libc6 (>= 2.3.6-6)
Description: Access software for a blind person using a soft braille terminal
Package: usb-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: usb-modules
Depends: kernel-image-2.6.18-6-486-di
Description: USB support
Package: libfribidi0-udeb
Status: install ok unpacked
Version: 0.10.7-4
Depends: libc6 (>= 2.3.6-6)
Description: Free Implementation of the Unicode BiDi algorithm
Package: libtextwrap1-udeb
Status: install ok installed
Version: 0.1-5
Depends: libc6 (>= 2.3.6-6)
Description: text-wrapping library with i18n - runtime udeb
Package: auto-install
Status: install ok unpacked
Version: 0.03
Depends: cdebconf-udeb, netcfg, preseed-common (>= 1.18)
Description: Support for automatic installs
Installer-Menu-Item: 19
Package: usb-discover
Status: install ok unpacked
Version: 1.06
Depends: cdebconf-udeb
Description: Discover USB and load kernel modules
Package: rescue-check
Status: install ok unpacked
Version: 1.9
Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03), di-utils (>= 1.18)
Description: enter d-i rescue mode if requested
Package: nano-udeb
Status: install ok unpacked
Version: 2.0.2-1etch1
Provides: editor
Depends: libc6 (>= 2.3.6-6), libslang2-udeb (>= 2.0.6-3)
Description: free Pico clone with some new features - tiny build
Package: cdebconf-udeb
Status: install ok installed
Version: 0.114etch1
Provides: debconf-2.0
Depends: libc6 (>= 2.3.6-6), libdebian-installer4-udeb (>= 0.50), libtextwrap1-udeb
Description: Debian Configuration Management System (C-implementation)
Package: ai-choosers
Status: install ok unpacked
Version: 0.03
Depends: kbd-chooser (>= 1.30), localechooser (>= 1.23)
Description: Delayed configuration of locale and keyboard for auto-install
Installer-Menu-Item: 22
Package: cdrom-core-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: cdrom-core-modules
Depends: kernel-image-2.6.18-6-486-di, scsi-core-modules-2.6.18-6-486-di, ide-modules-2.6.18-6-486-di
Description: CDROM support
Package: kernel-image-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: kernel-image, ext2-modules
Description: Linux kernel binary image for the Debian installer
Package: libiw28-udeb
Status: install ok installed
Version: 28-1
Depends: libc6 (>= 2.3.5-1)
Description: Tools for manipulating Linux Wireless Extensions
Package: load-cdrom
Status: install ok installed
Version: 1.14
Depends: cdebconf-udeb, cdrom-retriever, anna (>= 1.07)
Description: Load installer components from CD
Installer-Menu-Item: 16
Package: fat-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: fat-modules
Depends: kernel-image-2.6.18-6-486-di
Description: FAT filesystem support
Package: cdebconf-text-udeb
Status: install ok unpacked
Version: 0.114etch1
Depends: cdebconf-udeb, libc6 (>= 2.3.6-6)
Description: Plain text frontend for Debian Configuration Management System
Package: iso-3166-udeb
Status: install ok installed
Version: 1.0a-1
Description: provides iso_3166.tab file
Package: ide-core-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: ide-core-modules
Depends: kernel-image-2.6.18-6-486-di
Description: IDE support
Package: pcmcia-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: pcmcia-modules
Depends: kernel-image-2.6.18-6-486-di, firmware-modules-2.6.18-6-486-di
Description: Common PCMCIA drivers
Package: floppy-retriever
Status: install ok unpacked
Version: 1.14
Provides: retriever
Depends: cdebconf-udeb, mountfloppy
Description: Fetches modules from a floppy
Package: usb-storage-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: usb-storage-modules
Depends: ide-core-modules-2.6.18-6-486-di, scsi-core-modules-2.6.18-6-486-di, usb-modules-2.6.18-6-486-di
Description: USB storage support
Package: ethdetect
Status: install ok installed
Version: 1.50
Provides: ethernet-card-detection
Depends: rootskel (>= 1.30), cdebconf-udeb (>= 0.38), hw-detect, di-utils (>= 1.13)
Description: Detect network hardware and load kernel drivers for it
Installer-Menu-Item: 17
Package: scsi-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: scsi-modules
Depends: kernel-image-2.6.18-6-486-di, scsi-core-modules-2.6.18-6-486-di, parport-modules-2.6.18-6-486-di, cdrom-core-modules-2.6.18-6-486-di, firmware-modules-2.6.18-6-486-di
Description: SCSI drivers
Package: scsi-core-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: scsi-core-modules
Depends: kernel-image-2.6.18-6-486-di
Description: Core SCSI subsystem
Package: firewire-core-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: firewire-core-modules
Depends: scsi-core-modules-2.6.18-6-486-di, kernel-image-2.6.18-6-486-di
Description: Core FireWire drivers
Package: busybox-udeb
Status: install ok unpacked
Version: 1:1.1.3-4
Depends: libc6 (>= 2.3.6-6)
Description: Tiny utilities for the debian-installer
Package: initrd-preseed
Status: install ok unpacked
Version: 1.28
Depends: preseed-common
Description: load debconf preseed file from /preseed.cfg on the initrd
Package: archdetect
Status: install ok installed
Version: 1.50
Depends: libc6 (>= 2.3.6-6), libdebian-installer4-udeb (>= 0.50)
Description: Hardware architecture detector
Package: save-logs
Status: install ok unpacked
Version: 2.29
Depends: cdebconf-udeb
Description: save logs and configuration for debug purposes
Installer-Menu-Item: 940
Package: di-utils-reboot
Status: install ok unpacked
Version: 1.45etch1
Depends: cdebconf-udeb
Description: Reboot
Installer-Menu-Item: 995
Package: anna
Status: install ok installed
Version: 1.27
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.50), cdebconf-udeb
Description: anna's not nearly apt, but for the Debian installer, it will do
Package: firmware-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: firmware-modules
Depends: kernel-image-2.6.18-6-486-di
Description: Firmware request modules
Package: libsysfs2-udeb
Status: install ok unpacked
Version: 2.1.0-1
Provides: libsysfs2
Depends: libc6 (>= 2.3.6-6)
Description: interface library to sysfs
Package: pcmciautils-udeb
Status: install ok unpacked
Version: 014-3
Depends: udev-udeb, libc6 (>= 2.3.6-6), libsysfs2-udeb
Description: PCMCIA utilities for Linux 2.6
Package: pciutils-udeb
Status: install ok unpacked
Version: 1:2.2.4~pre4-1
Depends: libc6 (>= 2.3.6-6)
Description: Linux PCI Utilities (udeb)
Package: console-keymaps-at
Status: install ok installed
Version: 2:1.01-7
Provides: console-keymaps
Depends: cdebconf-udeb
Description: Keymaps for PC-style (PS/2 and AT) keyboards
Package: di-utils-terminfo
Status: install ok unpacked
Version: 1.45etch1
Description: Terminfo entries needed by newt/slang in debian installer
Package: hw-detect
Status: install ok installed
Version: 1.50
Depends: rootskel (>= 1.30), archdetect, cdebconf-udeb (>= 0.75), di-utils (>= 1.26)
Description: Detect hardware and load kernel drivers for it
Package: kbd-chooser
Status: install ok installed
Version: 1.34
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.50), cdebconf-udeb, console-keymaps
Description: Detect a keyboard and select layout
Installer-Menu-Item: 12
Package: libdebian-installer4-udeb
Status: install ok installed
Version: 0.50etch1
Depends: libc6 (>= 2.3.6-6)
Description: Library of common debian-installer functions
Package: scsi-common-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: scsi-common-modules
Depends: kernel-image-2.6.18-6-486-di, scsi-core-modules-2.6.18-6-486-di, cdrom-core-modules-2.6.18-6-486-di
Description: Very common SCSI drivers
Package: installation-locale
Status: install ok unpacked
Version: 1.1
Depends: rootskel
Description: UTF-8 C locale
Package: parport-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: parport-modules
Depends: kernel-image-2.6.18-6-486-di
Description: Parallel port support
Package: env-preseed
Status: install ok unpacked
Version: 1.28
Description: debconf preseeding via environment variables
Package: mountfloppy
Status: install ok unpacked
Version: 0.11
Depends: cdebconf-udeb, di-utils (>= 1.15)
Description: Mounts a floppy
Package: cdebconf-priority
Status: install ok unpacked
Version: 0.114etch1
Depends: cdebconf-udeb
Description: Change debconf priority
Installer-Menu-Item: 930
Package: netcfg
Status: install ok installed
Version: 1.36
Provides: configured-network
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.50), libiw28-udeb (>= 28), dhcp-client-udeb | dhcp3-client-udeb | pump-udeb, ethernet-card-detection
Description: Configure the network
Installer-Menu-Item: 18
Package: file-preseed
Status: install ok unpacked
Version: 1.28
Depends: cdebconf-udeb, di-utils, preseed-common
Description: load debconf preseed file
Installer-Menu-Item: 14
Package: floppy-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: floppy-modules
Depends: kernel-image-2.6.18-6-486-di
Description: Floppy driver
Package: pcmcia-storage-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: pcmcia-storage-modules
Depends: kernel-image-2.6.18-6-486-di, ide-core-modules-2.6.18-6-486-di, cdrom-core-modules-2.6.18-6-486-di, pcmcia-modules-2.6.18-6-486-di
Description: PCMCIA storage drivers
Package: libdebconfclient0-udeb
Status: install ok installed
Version: 0.114etch1
Depends: libc6 (>= 2.3.6-6), cdebconf-udeb
Description: Debian Configuration Management System (C-implementation)
Package: bogl-bterm-udeb
Status: install ok unpacked
Version: 0.1.18-1.5
Provides: editor
Depends: libc-udeb
Description: Ben's Own Graphics Library - graphical terminal
Package: fb-modules-2.6.18-6-486-di
Status: install ok unpacked
Version: 1.44etch3
Provides: fb-modules
Depends: kernel-image-2.6.18-6-486-di
Description: Frame buffer support
Package: cdrom-detect
Status: install ok installed
Version: 1.20etch1
Depends: cdebconf-udeb, hw-detect, di-utils (>= 1.45etch1)
Description: Detect CDROM devices and mount the CD
Installer-Menu-Item: 13
Package: debian-installer
Status: install ok installed
Version: cdrom-isolinux-20070308etch2
Description: debian installation image
Package: zlib1g-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 100
Maintainer: Mark Brown <broonie@debian.org>
Version: 1:1.2.3-13
Provides: zlib1g
Description: compression library - runtime for Debian installer
zlib is a library implementing the deflate compression method found
in gzip and PKZIP. This minimal package includes the shared library
for use with the Debian installer.
Package: apt-cdrom-setup
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 44
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.20etch1
Depends: cdrom-detect, cdebconf-udeb
Provides: apt-mirror-setup
Description: set up a CD in sources.list
Package: apt-mirror-setup
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 160
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.20etch1
Depends: choose-mirror-bin, cdebconf-udeb
Description: set up a mirror in sources.list
Package: apt-setup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 104
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.20etch1
Depends: apt-mirror-setup, base-installer (>= 1.49), cdebconf-udeb
Description: Configure apt
Installer-Menu-Item: 70
Package: base-installer
Status: install ok installed
Priority: required
Section: debian-installer
Installed-Size: 632
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.76
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.50), mounted-partitions, debootstrap-udeb (>= 0.3.1), created-fstab, archdetect, di-utils-mapdevfs, di-utils (>= 1.16), rootskel (>= 1.19), gpgv-udeb
Provides: kernel-installer
Description: Install the base system
Installer-Menu-Item: 65
Package: choose-mirror-bin
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 324
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 2.13etch2
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.50etch1), cdebconf-udeb
Description: Choose mirror to install from (program)
Package: clock-setup
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 76
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.15
Depends: cdebconf-udeb, os-prober, tzsetup-udeb
Description: set up clock
Installer-Menu-Item: 62
Package: crc-modules-2.6.18-6-486-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 32
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di
Provides: crc-modules
Description: CRC modules
This package contains CRC support modules.
Package: debootstrap-udeb
Status: install ok installed
Priority: required
Section: debian-installer
Installed-Size: 168
Maintainer: Anthony Towns <ajt@debian.org>
Version: 0.3.3.2etch1
Depends: libc6 (>= 2.3.6-6), mounted-partitions
Description: Bootstrap the Debian system
debootstrap is used to create a Debian base system from scratch,
without requiring the availability of dpkg or apt. It does this by
downloading .deb files from a mirror site, and carefully unpacking them
into a directory which can eventually be chrooted into.
.
debootstrap-udeb is a minimal package used by debian-installer.
Package: dhcp-client-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 132
Maintainer: Eloy A. Paris <peloy@debian.org>
Version: 2.0pl5-19.5etch2
Depends: libc6 (>= 2.3.6-6)
Description: DHCP Client for debian-installer
dhcp-client-udeb is a minimal dhcp package used by the debian-installer.
Package: di-utils-mapdevfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 16
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.45etch1
Depends: libc6 (>= 2.3.6-6), libdebian-installer4-udeb (>= 0.50)
Description: mapdevfs utility for the debian installer
Package: disk-detect
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 64
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.50
Depends: cdebconf-udeb (>= 0.38), hw-detect, di-utils (>= 1.13)
Provides: harddrive-detection
Description: Detect disk drives
Installer-Menu-Item: 35
Package: dmidecode-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 64
Maintainer: Petter Reinholdtsen <pere@debian.org>
Version: 2.8-4
Depends: libc6 (>= 2.3.6-6)
Description: Dump Desktop Management Interface data (udeb)
Package: e2fsprogs-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 356
Maintainer: Theodore Y. Ts'o <tytso@mit.edu>
Version: 1.39+1.40-WIP-2006.11.14+dfsg-2etch1
Depends: libblkid1-udeb, libc6 (>= 2.3.6-6)
Description: stripped-down versions of e2fsprogs, for debian-installer
This package is an e2fsprogs package built for a reduced size, so that
it can help to save space in debian-installer.
.
Don't attempt to install this package, it has no support for a couple of
features you surely want. Anyway it should refuse to install.
Package: efi-modules-2.6.18-6-486-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 44
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di
Provides: efi-modules
Description: EFI modules
This package contains EFI modules.
Package: elilo-installer
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 100
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.10
Depends: cdebconf-udeb, base-installer, partconf-find-partitions (>= 1.08), di-utils-mapdevfs, fat-modules, efi-modules, dmidecode-udeb (>= 2.7)
Provides: bootable-system
Description: Install elilo on a hard disk
Installer-Menu-Item: 76
Package: ext3-modules-2.6.18-6-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 240
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di
Provides: ext3-modules
Description: EXT3 filesystem support
This package contains the EXT3 filesystem module for the Linux kernel.
Package: fdisk-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 136
Maintainer: LaMont Jones <lamont@debian.org>
Version: 2.12r-19etch1
Depends: libc6 (>= 2.3.6-6)
Description: Partition a hard drive (manual)
fdisk package
Package: finish-install
Status: install ok unpacked
Priority: required
Section: debian-installer
Installed-Size: 108
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 2.9
Depends: cdebconf-udeb, archdetect, base-installer, created-fstab, bootable-system
Provides: prebaseconfig
Description: Finish the installation and reboot
Installer-Menu-Item: 78
Package: gpgv-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 256
Maintainer: James Troup <james@nocrew.org>
Version: 1.4.6-2
Depends: libc6 (>= 2.3.6-6), zlib1g-udeb (>= 1:1.2.1)
Description: minimal signature verification tool
GnuPG is GNU's tool for secure communication and data storage.
It can be used to encrypt data and to create digital signatures.
It includes an advanced key management facility and is compliant
with the proposed OpenPGP Internet standard as described in RFC2440.
.
This is GnuPG's signature verification tool, gpgv, packaged in minimal
form for use in debian-installer.
Package: grub-installer
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 340
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.22etch1
Depends: cdebconf-udeb, kernel-installer, created-fstab, di-utils (>= 1.15), di-utils-mapdevfs, os-prober, dmidecode-udeb (>= 2.7)
Provides: bootable-system
Description: Install GRUB on a hard disk
Installer-Menu-Item: 73
Package: jfs-modules-2.6.18-6-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 216
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di
Provides: jfs-modules
Description: JFS filesystem support
This package contains the JFS filesystem module for the Linux kernel.
Package: jfsutils-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 984
Maintainer: Stefan Hornburg (Racke) <racke@linuxia.de>
Version: 1.1.11-1
Depends: libc6 (>= 2.3.6-6), libuuid1-udeb
Description: A stripped-down version of jfsutils, for debian-installer
This package is a jfsutils package built for reduced size, so that it
can help to save space in debian-installer.
.
Don't attempt to install this package, it has no support for a couple of
features you surely want. Anyway, it should fail to install.
Package: libblkid1-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 40
Maintainer: Theodore Y. Ts'o <tytso@mit.edu>
Version: 1.39+1.40-WIP-2006.11.14+dfsg-2etch1
Depends: libc6 (>= 2.3.6-6)
Provides: libblkid1
Description: block device id library
The blkid library which allows system programs like fsck and
mount to quickly and easily find block devices by filesystem UUID and
LABEL. This allows system administrators to avoid specifiying
filesystems by hard-coded device names, but via a logical naming
system instead.
.
This is a minimal package for debian-installer.
Package: libc6-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 1584
Maintainer: GNU Libc Maintainers <debian-glibc@lists.debian.org>
Version: 2.3.6.ds1-13etch5
Provides: libc6, libc-udeb, glibc-2.3.6.ds1-1, glibc-2.3.6-2
Description: GNU C Library: Shared libraries - udeb
Contains the standard libraries that are used by nearly all programs on
the system. This package includes shared versions of the standard C library
and the standard math library, as well as many others.
.
This package contains a minimal set of libraries needed for the Debian
installer. Do not install it on a normal system.
Package: libdevmapper1.02-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 52
Maintainer: Debian LVM Team <pkg-lvm-maintainers@lists.alioth.debian.org>
Version: 2:1.02.08-1
Depends: libc6 (>= 2.3.6-6)
Provides: libdevmapper1.02
Description: The Linux Kernel Device Mapper userspace library
This is a udeb, or a microdeb, for the debian-installer.
.
The Linux Kernel Device Mapper is the LVM (Linux Logical Volume Management)
Team's implementation of a minimalistic kernel-space driver that handles
volume management, while keeping knowledge of the underlying device layout
in user-space. This makes it useful for not only LVM, but EVMS, software
raid, and other drivers that create "virtual" block devices.
Package: libparted1.7-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 340
Maintainer: Parted Maintainer Team <parted-maintainers@lists.alioth.debian.org>
Version: 1.7.1-5.1
Depends: libc6 (>= 2.3.6-6), libuuid1-udeb
Provides: libparted1.7-1
Description: The GNU Parted disk partitioning shared library
GNU Parted is a program that allows you to create, destroy,
resize, move and copy hard disk partitions. This is useful
for creating space for new operating systems, reorganising
disk usage, and copying data to new hard disks. This package
contains the Parted binary and manual page.
.
This package contains libparted, the required shared library
used by Parted. This is a cut-down package with no normal
documentation intended to be used in debian-installer.
.
Parted currently supports DOS, Mac, Sun, BSD, GPT, MIPS and
PC98 disklabels/partition tables, as well as a 'loop' (raw
disk) type which allows use on RAID/LVM. Filesystems which
are currently fully supported are ext2, ext3, fat (FAT16
and FAT32), ReiserFS (with libreiserfs) and linux-swap.
Parted can also detect and remove HFS (Mac OS), JFS, NTFS,
UFS (Sun and HP), XFS and ASFS/AFFS/APFS (Amiga) filesystems,
but cannot create, resize or check these filesystems yet.
.
Note that ReiserFS support is only enabled if you install
the libreiserfs0.3-0 package. Since libreiserfs0.3-0 has been
removed from sarge, ReiserFS support is not compiled in the
default package.
.
The nature of this software means that any bugs could cause
massive data loss. While there are no known bugs at the moment,
they could exist, so please back up all important files before
running it, and do so at your own risk.
Package: libuuid1-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 24
Maintainer: Theodore Y. Ts'o <tytso@mit.edu>
Version: 1.39+1.40-WIP-2006.11.14+dfsg-2etch1
Depends: libc6 (>= 2.3.6-6)
Provides: libuuid1
Description: universally unique id library
libuuid generates and parses 128-bit universally unique id's (UUID's).
See RFC 4122 for more information.
.
This is a minimal package for debian-installer.
Package: lilo-installer
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 232
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.20etch1
Depends: cdebconf-udeb, kernel-installer, di-utils (>= 1.15), di-utils-mapdevfs, fdisk-udeb, os-prober, dmidecode-udeb (>= 2.7)
Provides: bootable-system
Description: Install LILO on a hard disk
Installer-Menu-Item: 75
Package: loop-modules-2.6.18-6-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 52
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di
Provides: loop-modules
Description: Loopback filesystem support
This package contains loopback filesystem support for the Linux kernel.
Package: lvm2-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 408
Maintainer: Debian LVM Team <pkg-lvm-maintainers@lists.alioth.debian.org>
Version: 2.02.06-4etch1
Depends: libc6 (>= 2.3.6-6), libdevmapper1.02-udeb (>= 2:1.02.02-2)
Description: The Linux Logical Volume Manager
This is a udeb, or a microdeb, for the debian-installer.
.
This is LVM2, the rewrite of The Linux Logical Volume Manager. LVM
supports enterprise level volume management of disk and disk subsystems
by grouping arbitrary disks into volume groups. The total capacity of
volume groups can be allocated to logical volumes, which are accessed as
regular block devices.
Package: md-modules-2.6.18-6-486-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 436
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di
Provides: md-modules
Description: RAID and LVM support
This package contains RAID and LVM modules for the Linux kernel.
Package: mdadm-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 176
Maintainer: Debian mdadm maintainers <pkg-mdadm-devel@lists.alioth.debian.org>
Version: 2.5.6-9
Depends: libc6 (>= 2.3.6-6)
Description: tool to administer Linux MD arrays (software RAID)
mdadm is a program that can be used to create, manage, and monitor MD
arrays (e.g. software RAID, multipath devices).
.
mdadm-udeb is a minimal package used by the debian-installer.
Package: mdcfg-utils
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 412
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.21
Depends: cdebconf-udeb, di-utils (>= 1.16), md-modules, mdadm-udeb (>= 2.5.2), partconf-find-partitions
Description: Configure MD devices
Use this module to configure the MD devices.
Package: mkreiserfs-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 144
Maintainer: Ed Boraas <ed@debian.org>
Version: 1:3.6.19-4
Depends: libc6 (>= 2.3.6-6), libuuid1-udeb
Description: User-level tools for ReiserFS filesystems
This installer module contains the utility to create ReiserFS filesystems.
.
Homepage: http://www.namesys.com/
Package: network-preseed
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 40
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.28
Depends: cdebconf-udeb, configured-network, preseed-common
Description: download debconf preseed file
Installer-Menu-Item: 21
Package: nic-extra-modules-2.6.18-6-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 2992
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di, nic-shared-modules-2.6.18-6-486-di, firmware-modules-2.6.18-6-486-di, crc-modules-2.6.18-6-486-di
Provides: nic-extra-modules
Description: Rare NIC drivers
This package contains rare NIC drivers for the Linux kernel.
Package: nic-modules-2.6.18-6-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 444
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di, nic-shared-modules-2.6.18-6-486-di, firmware-modules-2.6.18-6-486-di, firewire-core-modules-2.6.18-6-486-di
Provides: nic-modules
Description: Common NIC drivers
This package contains common NIC drivers for the Linux kernel.
Package: nic-pcmcia-modules-2.6.18-6-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 572
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di, nic-shared-modules-2.6.18-6-486-di, nic-extra-modules-2.6.18-6-486-di, pcmcia-modules-2.6.18-6-486-di
Provides: nic-pcmcia-modules
Description: Common PCMCIA NIC drivers
This package contains common PCMCIA NIC drivers for the Linux kernel.
Package: nic-shared-modules-2.6.18-6-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 52
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di
Provides: nic-shared-modules
Description: Shared NIC drivers
This package contains NIC drivers needed by combinations of nic-modules,
nic-extra-modules, and nic-pcmcia-modules.
Package: nic-usb-modules-2.6.18-6-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 208
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di, nic-shared-modules-2.6.18-6-486-di, usb-modules-2.6.18-6-486-di, firmware-modules-2.6.18-6-486-di
Provides: nic-usb-modules
Description: USB NIC drivers
This package contains USB network adapter drivers for the Linux kernel.
Package: nobootloader
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 168
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.17
Depends: cdebconf-udeb, base-installer (>= 1.23), di-utils-mapdevfs
Provides: bootable-system
Description: Don't install any bootloader.
This package will skip installing a boot-loader
Installer-Menu-Item: 77
Package: ntfsprogs-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 244
Maintainer: David Mart?nez Moreno <ender@debian.org>
Version: 1.13.1-6+b2
Depends: libc6 (>= 2.3.6-6)
Provides: ntfstools-udeb
Description: Tools for doing neat things in NTFS partitions from Linux - udeb
Currently this udeb contains only ntfsresize.
Package: os-prober-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 128
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.17
Depends: di-utils-mapdevfs, anna (>= 1.16)
Provides: os-prober
Description: utility to detect other OSes on a set of drives
This package is to be used by boot loader installers to detect other OSes
available on a system, in a generic format, which it can then adapt to its
own configuration format.
Package: partconf-find-partitions
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 32
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.21
Depends: libc6 (>= 2.3.6-6), libdebian-installer4-udeb (>= 0.50), libparted1.7-udeb (>= 1.7.1-1)
Description: debian-installer utility for finding partitions
Helper program for finding partitions and detecting their size and
existing file system.
Package: parted-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 68
Maintainer: Parted Maintainer Team <parted-maintainers@lists.alioth.debian.org>
Version: 1.7.1-5.1
Depends: libc6 (>= 2.3.6-6), libparted1.7-udeb (>= 1.7.1-1)
Provides: parted
Description: The GNU Parted disk partition resizing program
GNU Parted is a program that allows you to create, destroy,
resize, move and copy hard disk partitions. This is useful
for creating space for new operating systems, reorganising
disk usage, and copying data to new hard disks. This package
contains the Parted binary and manual page.
.
This package is similar to the "big" parted package, but has
less cosmetical features resulting in smaller binary. Intended
to be used in debian-installer.
.
.
The nature of this software means that any bugs could cause
massive data loss. While there are no known bugs at the moment,
they could exist, so please back up all important files before
running it, and do so at your own risk.
Package: partman-auto
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 672
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 68etch1
Depends: cdebconf-udeb, di-utils, partman-base (>= 99), partman-basicfilesystems, partman-ext3
Description: Automatically partition storage devices (partman)
Package: partman-auto-crypto
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 48
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 5
Depends: cdebconf-udeb, partman-auto (>= 55), partman-auto-lvm (>= 14), partman-crypto (>= 13), partman-base (>= 87)
Description: Automatically partition storage devices using crypto and LVM
Package: partman-auto-lvm
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 164
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 22
Depends: cdebconf-udeb, partman-base (>= 73), partman-auto (>= 59), partman-lvm (>= 36), di-utils (>= 1.15), lvm2-udeb
Description: Automatically partition storage devices using LVM
Package: partman-auto-raid
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 68
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 5
Depends: cdebconf-udeb, partman-base (>= 99), partman-basicfilesystems, partman-ext3, partman-auto (>= 58), partman-md
Description: Allow preseeded RAID installs
Package: partman-base
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 872
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 105
Depends: libc6 (>= 2.3.6-6), libparted1.7-udeb (>= 1.7.1-1), cdebconf-udeb, partman-partitioning, partman-target, archdetect, harddrive-detection, di-utils-mapdevfs, di-utils (>= 1.15)
Provides: made-filesystems, mounted-partitions, partitioned-harddrives, created-fstab
Description: Partition the storage devices (partman)
Installer-Menu-Item: 42
Package: partman-basicfilesystems
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 600
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 53
Depends: cdebconf-udeb, e2fsprogs-udeb, ext2-modules, fat-modules, di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add to partman support for ext2, linux-swap, fat16 and fat32
Package: partman-basicmethods
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 132
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 34
Depends: cdebconf-udeb
Provides: partman-method
Description: Basic partition usage methods for partman
This package provides partman with two methods to use partitions.
The first is to format the partition. The second is to keep and use
the existing data in the partition as it is.
Package: partman-crypto
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 776
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 20etch1
Depends: partman-base (>= 87), libc6 (>= 2.3.6-6), cdebconf-udeb
Description: Add to partman support for block device encryption
Package: partman-efi
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 136
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 13
Depends: partman-base, efi-modules
Description: Add to partman support for EFI boot partitions
Package: partman-ext3
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 228
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 46
Depends: cdebconf-udeb, e2fsprogs-udeb, ext3-modules, partman-basicfilesystems, di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add to partman support for ext3
Package: partman-jfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 272
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 21
Depends: cdebconf-udeb, jfsutils-udeb, jfs-modules, partman-basicfilesystems, di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add support for jfs to partman
Package: partman-lvm
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 732
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 53
Depends: cdebconf-udeb, partman-base (>= 87), di-utils (>= 1.14), md-modules, lvm2-udeb, parted-udeb
Description: Adds support for LVM to partman
Package: partman-md
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 160
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 34
Depends: cdebconf-udeb, mdadm-udeb, mdcfg-utils, partman-base (>= 87)
Description: Add to partman support for MD
Package: partman-partitioning
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 380
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 48etch1
Depends: ntfsprogs-udeb, cdebconf-udeb
Description: Partitioning operations for partman
This udeb provides partman with editing operations for creation
of new partitions, deletion of partitions and initialisation of the
partition table.
Package: partman-reiserfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 236
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 35
Depends: cdebconf-udeb, mkreiserfs-udeb, reiserfs-modules, partman-basicfilesystems, di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add to partman support for reiserfs
Package: partman-target
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 320
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 49
Depends: cdebconf-udeb, partman-basicfilesystems, partman-basicmethods, di-utils-mapdevfs
Description: Provides partman with ability to prepare /target
This udeb allows the user to choose how partitions should be used.
Package: partman-xfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 224
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 33
Depends: cdebconf-udeb, xfsprogs-udeb, xfs-modules, partman-basicfilesystems, di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add to partman support for xfs
Package: pcmcia-cs-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 232
Maintainer: Per Olofsson <pelle@debian.org>
Version: 3.2.8-9
Description: PCMCIA Card Services for Linux (udeb)
Package: pkgsel
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 32
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.12
Depends: cdebconf-udeb, apt-setup-udeb, di-utils (>= 1.20)
Description: Select and install packages
Installer-Menu-Item: 70
Package: reiserfs-modules-2.6.18-6-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 268
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di
Provides: reiserfs-modules
Description: Reiser filesystem support
This package contains the Reiser filesystem module for the Linux kernel.
Package: scsi-extra-modules-2.6.18-6-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 1388
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: scsi-modules-2.6.18-6-486-di, scsi-core-modules-2.6.18-6-486-di
Provides: scsi-extra-modules
Description: Uncommon SCSI drivers
This package contains uncommon SCSI drivers for the Linux kernel.
This includes SCSI RAID drivers, and some of the less common SCSI
controllers.
Package: tzsetup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 308
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.16
Depends: cdebconf-udeb, localechooser
Description: choose timezone
Installer-Menu-Item: 62
Package: user-setup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 360
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.11etch1
Depends: cdebconf-udeb
Description: Set up users and passwords
Installer-Menu-Item: 63
Package: wireless-tools-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 28
Maintainer: Guus Sliepen <guus@debian.org>
Version: 28-1
Depends: libc6 (>= 2.3.5-1), libiw28-udeb (>= 28)
Description: Tools for manipulating Linux Wireless Extensions
This package contains the Wireless tools, used to manipulate the Linux
Wireless Extensions. The Wireless Extension is an interface allowing you to
set Wireless LAN specific parameters and get the specific stats.
.
This is a udeb of the wireless tools.
Package: xfs-modules-2.6.18-6-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 552
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di
Provides: xfs-modules
Description: XFS filesystem support
This package contains the XFS filesystem module for the Linux kernel.
Package: xfsprogs-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 232
Maintainer: Nathan Scott <nathans@debian.org>
Version: 2.8.11-1
Depends: libc6 (>= 2.3.6-6), libuuid1-udeb
Description: A stripped-down version of xfsprogs, for debian-installer
This package is an xfsprogs package built for reduced size, so that it
can help to save space in debian-installer.
.
Don't attempt to install this package, it has no support for a couple of
features you surely want. Anyway, it should fail to install.
Package: ntfs-modules-2.6.18-6-486-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 248
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di
Provides: ntfs-modules
Description: NTFS filesystem support
This package contains the NTFS file system module for the Linux kernel.
Package: qnx4-modules-2.6.18-6-486-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 48
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44etch3
Depends: kernel-image-2.6.18-6-486-di
Provides: qnx4-modules
Description: QNX4 filesystem support
This package contains the QNX4 filesystem module for the Linux kernel.
-- System Information:
Debian Release: 4.0
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Shell: /bin/sh linked to /bin/bash
Kernel: Linux 2.6.18-6-k7
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
installation-report depends on no packages.
Versions of packages installation-report recommends:
ii pciutils 1:2.2.4~pre4-1 Linux PCI Utilities
ii reportbug 3.31 reports bugs in the Debian distrib
-- no debconf information
--- End Message ---