--- Begin Message ---
Package: installation-reports
Boot method: Network
Image version: 17-05-2006 www.debian.org (amd64 daily snapshot)
Date: 17-05-2006 20:00 CET
Machine: Noname
Processor: AMD Athlon 64 3200+
Memory: 1 GB
Partitions:
Output of lspci and lspci -n:
lspci
0000:00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
0000:00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
0000:00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
0000:00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2)
0000:00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3)
0000:00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2)
0000:00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)
0000:00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)
0000:00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2)
0000:00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
0000:00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
0000:00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
0000:00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
0000:00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
0000:01:08.0 Network controller: RaLink Ralink RT2500 802.11 Cardbus Reference Card (rev 01)
0000:01:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)
0000:01:0d.0 Multimedia audio controller: Creative Labs SB Audigy LS
0000:02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 Gigabit Ethernet Controller (rev 15)
0000:03:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01)
0000:05:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600 GT] (rev a2)
lspci -n
0000:00:00.0 0580: 10de:005e (rev a3)
0000:00:01.0 0601: 10de:0050 (rev a3)
0000:00:01.1 0c05: 10de:0052 (rev a2)
0000:00:02.0 0c03: 10de:005a (rev a2)
0000:00:02.1 0c03: 10de:005b (rev a3)
0000:00:06.0 0101: 10de:0053 (rev f2)
0000:00:07.0 0101: 10de:0054 (rev f3)
0000:00:08.0 0101: 10de:0055 (rev f3)
0000:00:09.0 0604: 10de:005c (rev a2)
0000:00:0a.0 0680: 10de:0057 (rev a3)
0000:00:0b.0 0604: 10de:005d (rev a3)
0000:00:0c.0 0604: 10de:005d (rev a3)
0000:00:0d.0 0604: 10de:005d (rev a3)
0000:00:0e.0 0604: 10de:005d (rev a3)
0000:00:18.0 0600: 1022:1100
0000:00:18.1 0600: 1022:1101
0000:00:18.2 0600: 1022:1102
0000:00:18.3 0600: 1022:1103
0000:01:08.0 0280: 1814:0201 (rev 01)
0000:01:0c.0 0c00: 1106:3044 (rev 46)
0000:01:0d.0 0401: 1102:0007
0000:02:00.0 0200: 11ab:4362 (rev 15)
0000:03:00.0 0180: 1095:3132 (rev 01)
0000:05:00.0 0300: 10de:0140 (rev a2)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [E]
Create file systems: [ ]
Mount partitions: [ ]
Install base system: [ ]
Install boot loader: [ ]
Reboot: [ ]
Comments/Problems:
Could not manually perform partitioning. I could see only /dev/sda as a
whole disk but no partitions. I could create new partitions, but the old
ones were not visible! I could not afford going from scratch while other
OS was installed.
Please see attached dmesg output. I tried to erase one partition, but did
not help
Kind regards,
Bohdan
ered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI wakeup devices:
HUB0 XVR0 XVR1 XVR2 XVR3 USB0 USB2 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 148k freed
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
GSI 16 sharing vector 0xB1 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 16, io mem 0xfe02f000
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
pnp: the driver 'parport_pc' has been registered
pnp: match found with the PnP device '00:07' and the driver 'parport_pc'
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
GSI 17 sharing vector 0xB9 and IRQ 17
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 22 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:02.1: irq 17, io mem 0xfeb00000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
libata version 1.20 loaded.
sata_nv 0000:00:07.0: version 0.8
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
GSI 18 sharing vector 0xC1 and IRQ 18
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 21 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xF600 irq 18
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xF608 irq 18
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0xfb00-0xfb07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfb08-0xfb0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
ata1: dev 0 ATA-7, max UDMA/133, 488397168 sectors: LBA48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata1: dev 0 configured for UDMA/133
scsi0 : sata_nv
ohci_hcd 0000:00:02.0: wakeup
ata2: no device found (phy stat 00000000)
scsi1 : sata_nv
Vendor: ATA Model: ST3250823AS Rev: 3.03
Type: Direct-Access ANSI SCSI revision: 05
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
GSI 19 sharing vector 0xC9 and IRQ 19
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 20 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xF100 irq 19
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xF108 irq 19
hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
usb 1-1: new low speed USB device using ohci_hcd and address 2
ata3: no device found (phy stat 00000000)
scsi2 : sata_nv
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (22 C)
ata4: no device found (phy stat 00000000)
scsi3 : sata_nv
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda:ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
sda1 sda2 < sda5 sda6 sda7 sda8 > sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
vga16fb: initializing
vga16fb: mapped to 0xffff8100000a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
usb 1-5: new full speed USB device using ohci_hcd and address 3
input: Logitech USB Receiver as /class/input/input0
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
GSI 20 sharing vector 0xD1 and IRQ 20
ACPI: PCI Interrupt 0000:01:0c.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:01:0c.0, from 5 to 4
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20] MMIO=[fdeff000-fdeff7ff] Max Packet=[2048]
sata_sil24 0000:03:00.0: version 0.23
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
GSI 21 sharing vector 0xD9 and IRQ 21
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:03:00.0 to 64
ata5: SATA max UDMA/100 cmd 0xFFFFC20000070000 ctl 0x0 bmdma 0x0 irq 21
ata6: SATA max UDMA/100 cmd 0xFFFFC20000072000 ctl 0x0 bmdma 0x0 irq 21
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ata5: no device found (phy stat 00000000)
scsi4 : sata_sil24
ata6: no device found (phy stat 00000000)
scsi5 : sata_sil24
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00007ce819]
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
floppy0: no floppy controllers found
Probing IDE interface ide1...
sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.48.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:0a.0 to 64
eth1394: $Rev: 1312 $ Ben Collins <bcollins@debian.org>
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
eth1: forcedeth.c: subsystem: 01462:7100 bound to 0000:00:0a.0
floppy0: no floppy controllers found
floppy0: no floppy controllers found
program parted_devices is using a deprecated SCSI ioctl, please convert it to SG_IO
JFS: nTxBlock = 8015, nTxLock = 64121
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
program parted_devices is using a deprecated SCSI ioctl, please convert it to SG_IO
program parted_server is using a deprecated SCSI ioctl, please convert it to SG_IO
EXT2-fs warning (device sda8): ext2_fill_super: mounting ext3 filesystem as ext2
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 > sda3 sda4
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 > sda3 sda4
program parted_devices is using a deprecated SCSI ioctl, please convert it to SG_IO
program parted_server is using a deprecated SCSI ioctl, please convert it to SG_IO
EXT2-fs warning (device sda7): ext2_fill_super: mounting ext3 filesystem as ext2
--- End Message ---
--- Begin Message ---
We are closing this installation report for one of the following
reasons:
- it was reported with a pre-lenny version of Debian
Installer.
- indications in the installation report give the feeling that
the reported problem waslying in another software, unrelated to
D-I, which we can't easily identify.
- indications in the installation report suggest that it may have been
fixed in a more recent version of a D-I component
- it was successful and we forgot closing it..:-)
- it has no information we consider useful
The D-I team is currently in the process of cleaning out the old spool
of installation reports that haven't bene processed yet.
In case you think that the problem you reported has chances to be
still present, please reiterate your installation test with
a more recent image of D-I, if you're in position of doing this.
You'll find daily builds at
http://www.debian.org/devel/debian-installer. We recommend you choose
the netboot image, in the "daily builds section", then choose to
install "squeeze" when prompted.
If some problems are found, please report them with a new bug sent
against installation-reports.
Many thanks for your understanding and your help improving Debian,
past and present.
--- End Message ---