[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#418972: marked as done (cdrom: Etch does not detect CD-ROM on Acer Aspire 7100)

Your message dated Mon, 6 Sep 2010 21:50:09 +0200
with message-id <20100906215009.70bf14fe.linux@wansing-online.de>
and subject line Re: Bug#418972: State of bug # 418972: Close this bug
has caused the Debian Bug report #418972,
regarding cdrom: Etch does not detect CD-ROM on Acer Aspire 7100
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
418972: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=418972
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message --- 
Package: cdrom
Severity: grave
Justification: renders package unusable

I'm trying to install debian etch, so I downloaded this iso
http://ftp.br.debian.org/debian-cd/4.0_r0/i386/iso-cd/debian-40r0-i386-CD-1.iso
and burned it in a CD.
When I try to install it, I can't go any further than the DETECT AND 
MOUNT CDROM, cause the CD-ROM drive was not detected, i've tried loading 
all modules sugested but none where able to make the cdrom usable.

So I tried using NETBOOT.tar.gz to install the base system, to bypass 
the CDROM step. I managed to get to the partition HD, but again the 
installer would not detect my HD, so I couldn't partition/Install 
nothing.

I've entered this trouble in debian-user-portuguese, and a user 
recommended booting using these parameters,
BOOT_DEBUG=3
echo options libata atapi_enabled=1 >> /etc/modprobe.conf
echo ide-generic >> /etc/modprobe.conf
echo ata_piix >> /etc/modprobe.conf
echo sd_mod >> /etc/modprobe.conf

Despite the user's good will, none was efective, I still can get my 
cd-rom detected.

Thank you

my notebook is a  Acer Apire 7104WSMi:
Celeron M 1.6, 512Mb RAM

LSPCI attached ------------------------------
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML 
Express Processor to DRAM Controller (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 
915GM/GMS/910GML Express Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML 
Express Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 
Family) High Definition Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 
Family) PCI Express Port 1 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 
Family) USB UHCI #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 
Family) USB UHCI #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 
Family) USB UHCI #3 (rev 03)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 
Family) USB UHCI #4 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 
Family) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface 
Bridge (rev 03)
00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA 
Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) 
SMBus Controller (rev 03)
06:05.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 
54g] 802.11g Wireless LAN Controller (rev 02)
06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. 
RTL-8139/8139C/8139C+ (rev 10)
06:09.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller 
(rev 01)
end LSPCI ---------

DMESG ATTACHED -------- 
 Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
vesafb: framebuffer at 0xc0000000, mapped to 0xe0080000, using 1875k, 
total 7872k
vesafb: mode is 800x600x16, linelength=1600, pages=7
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 3
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 256k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 201, io base 0x00001820
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
libata version 2.00 loaded.
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 169, io base 0x00001840
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 209, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 217, io base 0x00001880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 201, io mem 0xb0004000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ XX XX XX XX ]
ata_piix 0000:00:1f.2: invalid MAP value 1
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1810 irq 14
scsi0 : ata_piix
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
scsi1 : ata_piix
ATA: abnormal status 0x7F on port 0x177
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with 
idebus=xx
Yenta: CardBus bridge found at 0000:06:09.0 [1025:0100]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:09.0, mfunc 0x00001022, devctl 0x44
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 
0xa04713/0x204000
input: SynPS/2 Synaptics TouchPad as /class/input/input1
Yenta: ISA IRQ mask 0x04f8, PCI irq 177
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0xb8000000 - 0xb80fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff
cs: IO port probe 0x100-0x3af: excluding 0x370-0x377
cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Getting cpuindex for acpiid 0x1
Time: acpi_pm clocksource has been installed.
ACPI: Thermal Zone [TZS0] (51 C)
ACPI: Thermal Zone [TZS1] (51 C)
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 
0xa04713/0x204000
input: SynPS/2 Synaptics TouchPad as /class/input/input2
psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for 
generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb1: VGA16 VGA frame buffer device
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
psmouse.c: TouchPad at isa0060/serio4/input0 - driver resynched.
floppy0: no floppy controllers found
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
ide1: I/O resource 0x170-0x177 not free.
ide1: ports already in use, skipping probe
end dmesg ----------------------------------------

--- End Message ---
--- Begin Message --- 
[Housecleaning on bugreports]

José María Escartín Esteban <ripero84@gmail.com> wrote:
> According to the release tags, bug 418972 is considered to be release-critical
> for both lenny (S) and squeeze (T).  However, it seems that it only affected
> etch (O).  Shouldn't the release tags be changed accordingly?

As this bug was reported for Etch, and the submitter was prompted to
check if the problem still exists in Lenny Beta2, but there was no reaction 
from submitter since:

I close this bug.


Thanks
Holger

-- 

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Created with Sylpheed 2.5.0
    under DEBIAN GNU/LINUX 5.0.0 - L e n n y
        Registered LinuxUser #311290 - http://counter.li.org/
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

--- End Message ---
Reply to: