Bug#514546: installation-report
Package: installation-reports
Boot method: Network (PXE)
Image version: Lenny RC2
http://ftp.nl.debian.org/debian/dists/testing/main/installer-i386/current/images/netboot/netboot.tar.gz
Date: 2009-02-05
Machine: Fit-PC 1.0
http://www.fit-pc.com/new/fit-pc-1-0-specifications.html
Processor: Geode LX800 (x86 compatible)
Memory: 256MB
Partitions:
Disk /dev/hda: 60.0 GB, 60011642880 bytes
255 heads, 63 sectors/track, 7296 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 * 1 7210 57914293+ 83 Linux
/dev/hda2 7211 7296 690795 5 Extended
/dev/hda5 7211 7296 690763+ 82 Linux swap / Solaris
Output of lspci -knn (or lspci -nn):
00:01.0 Host bridge [0600]: Advanced Micro Devices [AMD] CS5536 [Geode
companion] Host Bridge [1022:2080] (rev 33)
00:01.1 VGA compatible controller [0300]: Advanced Micro Devices [AMD]
Geode LX Video [1022:2081]
00:01.2 Entertainment encryption device [1010]: Advanced Micro Devices
[AMD] Geode LX AES Security Block [1022:2082]
Kernel driver in use: Geode LX AES
Kernel modules: geode-rng, geode-aes
00:0d.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Kernel driver in use: 8139too
Kernel modules: 8139too, 8139cp
00:0e.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Kernel driver in use: 8139too
Kernel modules: 8139too, 8139cp
00:0f.0 ISA bridge [0601]: Advanced Micro Devices [AMD] CS5536 [Geode
companion] ISA [1022:2090] (rev 03)
Kernel modules: cs5535_gpio
00:0f.2 IDE interface [0101]: Advanced Micro Devices [AMD] CS5536
[Geode companion] IDE [1022:209a] (rev 01)
Kernel driver in use: AMD_IDE
Kernel modules: amd74xx
00:0f.3 Multimedia audio controller [0401]: Advanced Micro Devices
[AMD] CS5536 [Geode companion] Audio [1022:2093] (rev 01)
Kernel driver in use: cs5535audio
Kernel modules: snd-cs5535audio
00:0f.4 USB Controller [0c03]: Advanced Micro Devices [AMD] CS5536
[Geode companion] OHC [1022:2094] (rev 02)
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:0f.5 USB Controller [0c03]: Advanced Micro Devices [AMD] CS5536
[Geode companion] EHC [1022:2095] (rev 02)
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [O]
Configure network: [O]
Detect CD: [ ]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [ ]
Install boot loader: [O]
Overall install: [O]
Comments/Problems:
Although the installer claimed to put the active ethernet device
first (when asking me to choose a device), it actually put the
inactive port (eth0) first. I believe both ports are controlled by the
same hardware device, so this isn't particularly unexpected.
Other than that, the install went well. I quite enjoyed the 'netboot'
install. My previous installs were 'floppy', which isn't nearly as
much fun.
Reply to: