Package: debian-installer
Version: snapshot-20071127
Hi,
i just tried installing Debian/Etch on an Sun Netra X1 and it failed. I
retried with a current snapshot from here:
http://people.debian.org/~stappers/d-i/images/20071127-12:10/netboot/boot.img
and it fails the same way. When gettint to the network configuration
both ethernets immediatly start flapping and DHCP does not succeed.
Dec 6 17:24:17.459 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down
Dec 6 17:24:21.060 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up
Dec 6 17:24:23.460 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down
Dec 6 17:24:27.060 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up
Dec 6 17:24:29.460 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down
Dec 6 17:24:33.060 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up
Dec 6 17:24:35.460 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down
Dec 6 17:24:41.260 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up
This seems to be caused by the driver unable to assign a MAC Address:
eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:9
eth1 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:10 Base address:0x100
This is the very same problem as #360699 reported which was closed.
Unloading dmfe.ko and loading tulip.ko (and removing dmfe.ko to
dismiss further loading) helps ...
00:05.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR+ <PERR+
Latency: 0 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1fe02010100 [size=256]
Region 1: Memory at 1ff00002000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at 1ff00080000 [disabled] [size=256K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=220mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR+ <PERR+
Latency: 0 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 1fe02010000 [size=256]
Region 1: [virtual] Memory at 1ff00000000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at 1ff00040000 [disabled] [size=256K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=220mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
At least the kernel does not Oops when unloading the dmfe driver as the
Etch installer kernel did for me...
Flo
--
Florian Lohoff flo@rfc822.org +49-171-2280134
Those who would give up a little freedom to get a little
security shall soon have neither - Benjamin Franklin
Attachment:
signature.asc
Description: Digital signature