As requested, here are various outputs from Etch Installer VT2, followed by corresponding outputs
from Sarge Installer VT2. Syslogs are attached.
--Paul
======================ETCH OUTPUT BEGINS HERE==================
# wget http://www.debian.org
wget: www.debian.org: Host name lookup failure
# wget http://194.109.137.218
Connecting to 194.109.137.218[194.109.137.218]:80
wget: Unable to connect to remote host (194.109.137.218): No route to host
# dmesg
x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 8
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
Time: tsc clocksource has been installed.
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 256k freed
input: AT Translated Set 2 keyboard as /class/input/input0
Yenta: CardBus bridge found at 0000:00:02.0 [1014:00eb]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.0, mfunc 0xfba97543, devctl 0x62
Yenta TI: socket 0000:00:02.0 probing PCI interrupt failed, trying to fix
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Yenta TI: socket 0000:00:02.0 no PCI interrupts. Fish. Please report.
Yenta: no PCI IRQ, CardBus support disabled for this socket.
Yenta: check your BIOS CardBus, BIOS IRQ or ACPI settings.
USB Universal Host Controller Interface driver v3.0
Yenta: ISA IRQ mask 0x04b8, PCI irq 0
Socket status: 30000006
Yenta: CardBus bridge found at 0000:00:02.1 [1014:00eb]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.1, mfunc 0xfba97543, devctl 0x62
Yenta TI: socket 0000:00:02.1 probing PCI interrupt failed, trying to fix
pnp: Device 00:04 activated.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
Yenta TI: socket 0000:00:02.1 no PCI interrupts. Fish. Please report.
Yenta: no PCI IRQ, CardBus support disabled for this socket.
Yenta: check your BIOS CardBus, BIOS IRQ or ACPI settings.
Yenta: ISA IRQ mask 0x0438, PCI irq 0
Socket status: 30000010
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfcf8-0xfcff, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
hda: WL, ATA DISK drive
pccard: PCMCIA card inserted into slot 1
cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x370-0x377
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x370-0x377
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
cs: memory probe 0x60000000-0x60ffffff: clean.
pcmcia: registering new device pcmcia1.0
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA CD-ROM XM-1902B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt Link [LNKD] disabled and referenced, BIOS bug
ACPI: PCI Interrupt Link [LNKD] BIOS reported IRQ 0, using IRQ 10
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
irq 10: nobody cared (try booting with the "irqpoll" option)
[<c0131ea7>] __report_bad_irq+0x2b/0x69
[<c013206d>] note_interrupt+0x188/0x1bf
[<c01317c3>] handle_IRQ_event+0x23/0x49
[<c013185b>] __do_IRQ+0x72/0xa1
[<c010506f>] do_IRQ+0x43/0x50
[<c0103a9a>] common_interrupt+0x1a/0x20
[<c013007b>] audit_handle_ievent+0x38/0x9a
[<c011855a>] __do_softirq+0x2c/0x75
[<c01185c5>] do_softirq+0x22/0x26
[<c0105074>] do_IRQ+0x48/0x50
[<c0103a9a>] common_interrupt+0x1a/0x20
[<c0131bd9>] setup_irq+0x128/0x184
[<ca84829b>] usb_hcd_irq+0x0/0x4a [usbcore]
[<c0131caa>] request_irq+0x75/0x90
[<ca847f5d>] usb_add_hcd+0x205/0x47d [usbcore]
[<c02188f7>] pcibios_set_master+0x1b/0x7a
[<ca84ec03>] usb_hcd_pci_probe+0x1dc/0x265 [usbcore]
[<c02012d2>] __driver_attach+0x0/0x59
[<c01b3773>] pci_device_probe+0x36/0x57
[<c0201235>] driver_probe_device+0x42/0x8b
[<c0201308>] __driver_attach+0x36/0x59
[<c0200d60>] bus_for_each_dev+0x37/0x59
[<c020119f>] driver_attach+0x11/0x13
[<c02012d2>] __driver_attach+0x0/0x59
[<c0200a6f>] bus_add_driver+0x5d/0xfa
[<c01b388f>] __pci_register_driver+0x34/0x4e
[<ca834055>] uhci_hcd_init+0x55/0x92 [uhci_hcd]
[<c01299cc>] sys_init_module+0x13a9/0x14ea
[<ca87c000>] parport_parse_param+0x0/0xbe [parport_pc]
[<c0102a47>] syscall_call+0x7/0xb
handlers:
[<ca84829b>] (usb_hcd_irq+0x0/0x4a [usbcore])
Disabling IRQ #10
uhci_hcd 0000:00:07.2: irq 10, io base 0x00008400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hda: max request size: 128KiB
hda: 23579136 sectors (12072 MB) w/347KiB Cache, CHS=23392/16/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 hda3
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ACPI: Transitioning device [FN00] to D3
ACPI: Transitioning device [FN00] to D3
ACPI: Fan [FN00] (off)
ACPI: Transitioning device [FN20] to D3
ACPI: Transitioning device [FN20] to D3
ACPI: Fan [FN20] (off)
ACPI: Transitioning device [FN60] to D3
ACPI: Transitioning device [FN60] to D3
ACPI: Fan [FN60] (off)
ACPI: Transitioning device [FN70] to D3
ACPI: Transitioning device [FN70] to D3
ACPI: Fan [FN70] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
Time: acpi_pm clocksource has been installed.
ACPI: Thermal Zone [THM0] (56 C)
ACPI: Thermal Zone [THM2] (36 C)
ACPI: Thermal Zone [THM6] (27 C)
ACPI: Thermal Zone [THM7] (27 C)
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
eth0: Xircom: port 0x300, irq 3, hwaddr 00:10:A4:F4:0F:20
eth0: MII link partner: 41e1
eth0: MII selected
eth0: media 100BaseT, silicon revision 4
eth0: MII link partner: 41e1
eth0: MII selected
eth0: media 100BaseT, silicon revision 4
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
JFS: nTxBlock = 1245, nTxLock = 9963
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
EXT2-fs warning (device hda1): ext2_fill_super: mounting ext3 filesystem as ext2
# ifconfig
eth0 Link encap:Ethernet HWaddr 00:10:A4:F4:0F:20
inet addr:192.168.1.202 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:3150 (3.0 KiB)
Interrupt:3 Base address:0x300
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:10 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:904 (904.0 B) TX bytes:904 (904.0 B)
# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
0.0.0.0 192.168.1.201 0.0.0.0 UG 0 0 0 eth0
======================ETCH OUTPUT ENDS HERE==================
======================SARGE OUTPUT BEGINS HERE==================
# wget http://www.debian.org
Connecting to www.debian.org[194.109.137.218]:80
index.html 0% | | 0 --:-- ETA
index.html 100% |*****************************| 14160 00:00 ETA
# wget http://194.109.137.218
Connecting to 194.109.137.218[194.109.137.218]:80
index.html 0% | | 0 --:-- ETA
index.html 100% |*****************************| 1457 00:00 ETA
# dmesg
009fdf000 - 0000000009fe0000 (ACPI NVS)
BIOS-e820: 0000000009fe0000 - 000000000a000000 (reserved)
BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
159MB LOWMEM available.
On node 0 totalpages: 40912
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 36816 pages, LIFO batch:8
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI disabled because your bios is from 1999 and too old
You can enable it with acpi=force
Built 1 zonelists
Kernel command line: vga=normal initrd=/install/2.6/initrd.gz ramdisk_size=10240 root=/dev/rd/0
devfs=mount,dall rw -- BOOT_IMAGE=/install/2.6/vmlinuz
Local APIC disabled by BIOS -- reenabling.
Could not enable APIC!
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 364.018 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 156124k/163648k available (1335k kernel code, 6936k reserved, 733k data, 204k init, 0k
highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 716.80 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040
CPU: Intel Mobile Pentium II stepping 0a
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 2932k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd880, last bus=7
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fe700
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xe724, dseg 0xf0000
pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0a: ioport range 0x15e0-0x15ef has been reserved
pnp: 00:0a: ioport range 0xef00-0xefaf has been reserved
PnPBIOS: 23 nodes reported by PnP BIOS; 23 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
pnp: Device 00:0d activated.
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 8
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
VFS: Mounted root (ext2 filesystem).
Trying to move old root to /initrd ... okay
Mounted devfs on /dev
Freeing unused kernel memory: 204k freed
NET: Registered protocol family 1
thermal: Unknown symbol acpi_processor_set_thermal_limit
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
PCI: Found IRQ 11 for device 0000:00:07.2
uhci_hcd 0000:00:07.2: Intel Corp. 82371AB/EB/MB PIIX4 USB
uhci_hcd 0000:00:07.2: irq 11, io base 00008400
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
vesafb: probe of vesafb0 failed with error -6
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb0: VGA16 VGA frame buffer device
Console: switching to colour frame buffer device 80x30
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 0000:00:02.0
PCI: Sharing IRQ 11 with 0000:00:06.0
PCI: Sharing IRQ 11 with 0000:01:00.0
Yenta: CardBus bridge found at 0000:00:02.0 [1014:00eb]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.0, mfunc 0xfba97543, devctl 0x62
Yenta: ISA IRQ mask 0x06b8, PCI irq 11
Socket status: 30000006
PCI: Found IRQ 11 for device 0000:00:02.1
Yenta: CardBus bridge found at 0000:00:02.1 [1014:00eb]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.1, mfunc 0xfba97543, devctl 0x62
Yenta: ISA IRQ mask 0x06b8, PCI irq 11
Socket status: 30000010
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
inserting floppy driver for 2.6.8-2-386
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfcf8-0xfcff, BIOS settings: hdc:DMA, hdd:pio
hda: WL, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: TOSHIBA CD-ROM XM-1902B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 23579136 sectors (12072 MB) w/347KiB Cache, CHS=23392/16/63, UDMA(33)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
cs: IO port probe 0x0100-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
cs: memory probe 0x60000000-0x60ffffff: clean.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
eth0: Xircom: port 0x300, irq 3, hwaddr 00:10:A4:F4:0F:20
NET: Registered protocol family 17
eth0: MII link partner: 41e1
eth0: MII selected
eth0: media 100BaseT, silicon revision 4
eth0: MII link partner: 41e1
eth0: MII selected
eth0: media 100BaseT, silicon revision 4
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
EXT2-fs warning (device hda1): ext2_fill_super: mounting ext3 filesystem as ext2
# ifconfig
eth0 Link encap:Ethernet HWaddr 00:10:A4:F4:0F:20
inet addr:192.168.1.202 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:49 errors:0 dropped:0 overruns:0 frame:0
TX packets:57 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:35279 (34.4 KiB) TX bytes:5560 (5.4 KiB)
Interrupt:3 Base address:0x300
# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
0.0.0.0 192.168.1.201 0.0.0.0 UG 0 0 0 eth0
======================SARGE OUTPUT ENDS HERE==================
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com Attachment:
etch-syslog.gz
Description: 1169601280-etch-syslog.gz
Attachment:
sarge-syslog.gz
Description: 613761171-sarge-syslog.gz