Bug#410735: installation-report: tasksel should give information about discspace
Package: installation-reports
Version: 2.23
Severity: wishlist
-- Package-specific info:
Boot method: floppy
Image version: http://people.debian.org/~joeyh/d-i//images/daily 2007 02 11
Date: <Date and time of the install>
Machine: Pentium I
Partitions: <df -Tl will do; the raw partition table is preferred>
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [E]
Configure network: [O]
Detect CD: [ ]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [O]
Install boot loader: [O]
Overall install: [O]
Comments/Problems:
<Description of the install, in prose, and any thoughts, comments
and ideas you had during the initial install.>
Hello,
I had problems to install Etch on this old machine:
During package selection in tasksel I had accidently selected "desktop-system".
(The German version of the installation manual (section D2) said
that this would take 1.7 GB diskspace.)
Unfortunally tasksel gives no information about the requiered diskspace and
at the point where I recognized that there is not enough disk space, there were
no way to get back to the package selection.
(The installer lead me back to the tasksel selection, but it was impossible to
correct the selection in tasksel.)
So I had to restart the installation from scratch.
Second problem:
The German manual says "reportbug installation-reports" should be called.
But it doesn't seem to work this way.
I had to call "reportbug installation-report" (without the 's').
Concerning the "Detect network card" I had to select manually the
smc_ultra ISA card.
Greetings
Juergen
--
Please make sure that the hardware-summary log file, and any other
installation logs that you think would be useful are attached to this
report.
Once you have filled out this report, mail it to submit@bugs.debian.org.
==============================================
Installer lsb-release:
==============================================
DISTRIB_ID=Debian
DISTRIB_DESCRIPTION="Debian GNU/Linux installer"
DISTRIB_RELEASE="4.0 (installer build 20070211-04:02)"
X_INSTALLATION_MEDIUM=floppy
==============================================
Installer hardware-summary:
==============================================
umame -a: Linux salvatore 2.6.18-4-486 #1 Fri Feb 2 14:29:35 UTC 2007 i586 unknown
lspci -nn: 00:00.0 Host bridge [0600]: Intel Corporation 430FX - 82437FX TSC [Triton I] [8086:122d] (rev 02)
lspci -nn: 00:07.0 ISA bridge [0601]: Intel Corporation 82371FB PIIX ISA [Triton I] [8086:122e] (rev 02)
lspci -nn: 00:07.1 IDE interface [0101]: Intel Corporation 82371FB PIIX IDE [Triton I] [8086:1230] (rev 02)
lspci -vnn: 00:00.0 Host bridge [0600]: Intel Corporation 430FX - 82437FX TSC [Triton I] [8086:122d] (rev 02)
lspci -vnn: Flags: bus master, medium devsel, latency 32
lspci -vnn:
lspci -vnn: 00:07.0 ISA bridge [0601]: Intel Corporation 82371FB PIIX ISA [Triton I] [8086:122e] (rev 02)
lspci -vnn: Flags: bus master, medium devsel, latency 0
lspci -vnn:
lspci -vnn: 00:07.1 IDE interface [0101]: Intel Corporation 82371FB PIIX IDE [Triton I] [8086:1230] (rev 02) (prog-if 80 [Master])
lspci -vnn: Flags: bus master, medium devsel, latency 32
lspci -vnn: I/O ports at e800 [size=16]
lspci -vnn:
modulemap: 8086:122e piix
modulemap: 8086:1230 piix
lsmod: Module Size Used by
lsmod: ipv6 213728 8
lsmod: qnx4 10612 0
lsmod: ntfs 184084 0
lsmod: xfs 464756 0
lsmod: reiserfs 210432 0
lsmod: jfs 156380 0
lsmod: ext3 116488 1
lsmod: jbd 47272 1 ext3
lsmod: vfat 11648 0
lsmod: fat 45980 1 vfat
lsmod: isofs 31928 0
lsmod: ide_generic 1536 0 [permanent]
lsmod: aec62xx 6912 0 [permanent]
lsmod: alim15x3 11148 0 [permanent]
lsmod: amd74xx 13084 0 [permanent]
lsmod: atiixp 5648 0 [permanent]
lsmod: cmd64x 10012 0 [permanent]
lsmod: cs5520 4736 0 [permanent]
lsmod: cs5530 4992 0 [permanent]
lsmod: cs5535 4352 0 [permanent]
lsmod: cy82c693 4484 0 [permanent]
lsmod: hpt34x 5120 0 [permanent]
lsmod: it821x 7940 0 [permanent]
lsmod: jmicron 4224 0 [permanent]
lsmod: ns87415 4296 0 [permanent]
lsmod: opti621 4228 0 [permanent]
lsmod: pdc202xx_new 8064 0 [permanent]
lsmod: pdc202xx_old 9472 0 [permanent]
lsmod: rz1000 2816 0 [permanent]
lsmod: sc1200 6656 0 [permanent]
lsmod: serverworks 8456 0 [permanent]
lsmod: siimage 11136 0 [permanent]
lsmod: sis5513 12552 0 [permanent]
lsmod: slc90e66 5120 0 [permanent]
lsmod: triflex 3840 0 [permanent]
lsmod: trm290 4228 0 [permanent]
lsmod: via82cxxx 8452 0 [permanent]
lsmod: usb_storage 71360 0
lsmod: scsi_mod 121992 1 usb_storage
lsmod: ide_cd 35616 0
lsmod: cdrom 32416 1 ide_cd
lsmod: ide_disk 14848 3
lsmod: generic 5124 0 [permanent]
lsmod: piix 9220 0 [permanent]
lsmod: ide_core 107760 31 ide_generic,aec62xx,alim15x3,amd74xx,atiixp,cmd64x,cs5520,cs5530,cs5535,cy82c693,hpt34x,it821x,jmicron,ns87415,opti621,pdc202xx_new,pdc202xx_old,rz1000,sc1200,serverworks,siimage,sis5513,slc90e66,triflex,trm290,via82cxxx,usb_storage,ide_cd,ide_disk,generic,piix
lsmod: smc_ultra 6580 0
lsmod: 8390 8704 1 smc_ultra
lsmod: rsrc_nonstatic 11904 0
lsmod: pcmcia_core 36240 1 rsrc_nonstatic
lsmod: parport_pc 31524 0
lsmod: parport 32200 1 parport_pc
lsmod: usbhid 35552 0
lsmod: usbkbd 6656 0
lsmod: usbcore 108676 3 usb_storage,usbhid,usbkbd
lsmod: processor 23212 0
lsmod: floppy 51748 0
df: Filesystem 1k-blocks Used Available Use% Mounted on
df: tmpfs 102400 14868 87532 15% /
df: tmpfs 31112 404 30708 1% /dev
df: tmpfs 31112 404 30708 1% /dev
df: tmpfs 31112 404 30708 1% /.dev
df: /dev/ide/host0/bus0/target0/lun0/part1 1921156 500256 1323308 27% /target
free: total used free shared buffers
free: Mem: 62224 58648 3576 0 3564
free: Swap: 152576 14832 137744
free: Total: 214800 73480 141320
cardctl status: /usr/bin/report-hw: /usr/bin/report-hw: 50: cardctl: not found
cardctl ident: /usr/bin/report-hw: /usr/bin/report-hw: 51: cardctl: not found
/proc/cpuinfo: processor : 0
/proc/cpuinfo: vendor_id : GenuineIntel
/proc/cpuinfo: cpu family : 5
/proc/cpuinfo: model : 2
/proc/cpuinfo: model name : Pentium 75 - 200
/proc/cpuinfo: stepping : 5
/proc/cpuinfo: cpu MHz : 74.706
/proc/cpuinfo: cache size : 0 KB
/proc/cpuinfo: fdiv_bug : no
/proc/cpuinfo: hlt_bug : no
/proc/cpuinfo: f00f_bug : no
/proc/cpuinfo: coma_bug : no
/proc/cpuinfo: fpu : yes
/proc/cpuinfo: fpu_exception : yes
/proc/cpuinfo: cpuid level : 1
/proc/cpuinfo: wp : yes
/proc/cpuinfo: flags : fpu vme de pse tsc msr mce cx8
/proc/cpuinfo: bogomips : 149.99
/proc/cpuinfo:
/proc/ioports: 0000-001f : dma1
/proc/ioports: 0020-0021 : pic1
/proc/ioports: 0040-0043 : timer0
/proc/ioports: 0050-0053 : timer1
/proc/ioports: 0060-006f : keyboard
/proc/ioports: 0080-008f : dma page reg
/proc/ioports: 00a0-00a1 : pic2
/proc/ioports: 00c0-00df : dma2
/proc/ioports: 00f0-00ff : fpu
/proc/ioports: 0170-0177 : ide1
/proc/ioports: 01f0-01f7 : ide0
/proc/ioports: 02f8-02ff : serial
/proc/ioports: 0300-031f : smc-ultra
/proc/ioports: 0376-0376 : ide1
/proc/ioports: 0378-037a : parport0
/proc/ioports: 037b-037f : parport0
/proc/ioports: 03c0-03df : vga+
/proc/ioports: 03f2-03f5 : floppy
/proc/ioports: 03f6-03f6 : ide0
/proc/ioports: 03f7-03f7 : floppy DIR
/proc/ioports: 03f8-03ff : serial
/proc/ioports: 0cf8-0cff : PCI conf1
/proc/ioports: e800-e80f : 0000:00:07.1
/proc/ioports: e800-e807 : ide0
/proc/ioports: e808-e80f : ide1
/proc/iomem: 00000000-0009ffff : System RAM
/proc/iomem: 00000000-00000000 : Crash kernel
/proc/iomem: 000a0000-000bffff : Video RAM area
/proc/iomem: 000c0000-000c7fff : Video ROM
/proc/iomem: 000f0000-000fffff : System ROM
/proc/iomem: 00100000-03ffffff : System RAM
/proc/iomem: 00100000-00277829 : Kernel code
/proc/iomem: 0027782a-0030dc73 : Kernel data
/proc/iomem: ffff0000-ffffffff : reserved
/proc/interrupts: CPU0
/proc/interrupts: 0: 1992362 XT-PIC timer
/proc/interrupts: 1: 754 XT-PIC i8042
/proc/interrupts: 2: 0 XT-PIC cascade
/proc/interrupts: 6: 593 XT-PIC floppy
/proc/interrupts: 7: 0 XT-PIC parport0
/proc/interrupts: 10: 106879 XT-PIC eth0
/proc/interrupts: 14: 66575 XT-PIC ide0
/proc/interrupts: 15: 216 XT-PIC ide1
/proc/interrupts: NMI: 0
/proc/interrupts: LOC: 0
/proc/interrupts: ERR: 0
/proc/interrupts: MIS: 0
/proc/meminfo: MemTotal: 62224 kB
/proc/meminfo: MemFree: 3488 kB
/proc/meminfo: Buffers: 3564 kB
/proc/meminfo: Cached: 42504 kB
/proc/meminfo: SwapCached: 3592 kB
/proc/meminfo: Active: 26292 kB
/proc/meminfo: Inactive: 24024 kB
/proc/meminfo: HighTotal: 0 kB
/proc/meminfo: HighFree: 0 kB
/proc/meminfo: LowTotal: 62224 kB
/proc/meminfo: LowFree: 3488 kB
/proc/meminfo: SwapTotal: 152576 kB
/proc/meminfo: SwapFree: 137772 kB
/proc/meminfo: Dirty: 412 kB
/proc/meminfo: Writeback: 0 kB
/proc/meminfo: AnonPages: 2020 kB
/proc/meminfo: Mapped: 1272 kB
/proc/meminfo: Slab: 4708 kB
/proc/meminfo: PageTables: 216 kB
/proc/meminfo: NFS_Unstable: 0 kB
/proc/meminfo: Bounce: 0 kB
/proc/meminfo: CommitLimit: 183688 kB
/proc/meminfo: Committed_AS: 22104 kB
/proc/meminfo: VmallocTotal: 974544 kB
/proc/meminfo: VmallocUsed: 3172 kB
/proc/meminfo: VmallocChunk: 970768 kB
/proc/bus/input/devices: I: Bus=0011 Vendor=0001 Product=0001 Version=ab41
/proc/bus/input/devices: N: Name="AT Translated Set 2 keyboard"
/proc/bus/input/devices: P: Phys=isa0060/serio0/input0
/proc/bus/input/devices: S: Sysfs=/class/input/input0
/proc/bus/input/devices: H: Handlers=kbd
/proc/bus/input/devices: B: EV=120013
/proc/bus/input/devices: B: KEY=4 2000000 3802078 f840d001 feffffdf ffefffff ffffffff fffffffe
/proc/bus/input/devices: B: MSC=10
/proc/bus/input/devices: B: LED=7
/proc/bus/input/devices:
dmidecode: # dmidecode 2.8
dmidecode: Legacy DMI 2.0 present.
dmidecode: 30 structures occupying 1015 bytes.
dmidecode: Table at 0x000F509A.
dmidecode:
dmidecode: Handle 0x0000, DMI type 0, 18 bytes
dmidecode: BIOS Information
dmidecode: Vendor: Award Software, Inc.
dmidecode: Version: #401A0-0302
dmidecode: Release Date: 12/30/97
dmidecode: Address: 0xF0000
dmidecode: Runtime Size: 64 kB
dmidecode: ROM Size: 128 kB
dmidecode: Characteristics:
dmidecode: ISA is supported
dmidecode: PCI is supported
dmidecode: PNP is supported
dmidecode: APM is supported
dmidecode: BIOS is upgradeable
dmidecode: BIOS shadowing is allowed
dmidecode: ESCD support is available
dmidecode: Boot from CD is supported
dmidecode: Selectable boot is supported
dmidecode: BIOS ROM is socketed
dmidecode: EDD is supported
dmidecode: Japanese floppy for NEC 9800 1.2 MB is supported (int 13h)
dmidecode: 5.25"/360 KB floppy services are supported (int 13h)
dmidecode: 5.25"/1.2 MB floppy services are supported (int 13h)
dmidecode: 3.5"/720 KB floppy services are supported (int 13h)
dmidecode: 3.5"/2.88 MB floppy services are supported (int 13h)
dmidecode: Print screen service is supported (int 5h)
dmidecode: 8042 keyboard services are supported (int 9h)
dmidecode: Serial services are supported (int 14h)
dmidecode: Printer services are supported (int 17h)
dmidecode: CGA/mono video services are supported (int 10h)
dmidecode:
dmidecode: Handle 0x0001, DMI type 1, 8 bytes
dmidecode: System Information
dmidecode: Manufacturer: System Manufacturer
dmidecode: Product Name: System Name
dmidecode: Version: System Version
dmidecode: Serial Number: SYS-1234567890
dmidecode:
dmidecode: Handle 0x0002, DMI type 2, 8 bytes
dmidecode: Base Board Information
dmidecode: Manufacturer: ASUSTeK Computer INC.
dmidecode: Product Name: P/I-P55TP4N
dmidecode: Version: REV 1.X
dmidecode: Serial Number: MB-1234567890
dmidecode:
dmidecode: Handle 0x0003, DMI type 3, 9 bytes
dmidecode: Chassis Information
dmidecode: Manufacturer: Chassis Manufacture
dmidecode: Type: Unknown
dmidecode: Lock: Not Present
dmidecode: Version: Chassis Version
dmidecode: Serial Number: Chassis Serial Number
dmidecode: Asset Tag: Asset-1234567890
dmidecode:
dmidecode: Handle 0x0004, DMI type 4, 26 bytes
dmidecode: Processor Information
dmidecode: Socket Designation: SOCKET 7
dmidecode: Type: Central Processor
dmidecode: Family: Pentium
dmidecode: Manufacturer: Intel Corporation
dmidecode: ID: 25 05 00 00 BF 01 00 00
dmidecode: Signature: Type 0, Family 5, Model 2, Stepping 5
dmidecode: Flags:
dmidecode: FPU (Floating-point unit on-chip)
dmidecode: VME (Virtual mode extension)
dmidecode: DE (Debugging extension)
dmidecode: PSE (Page size extension)
dmidecode: TSC (Time stamp counter)
dmidecode: MSR (Model specific registers)
dmidecode: MCE (Machine check exception)
dmidecode: CX8 (CMPXCHG8 instruction supported)
dmidecode: Version: Intel Pentium Processor
dmidecode: Voltage: 3.3 V
dmidecode: External Clock: 50 MHz
dmidecode: Max Speed: 200 MHz
dmidecode: Current Speed: 75 MHz
dmidecode: Status: Populated, Enabled
dmidecode: Upgrade: ZIF Socket
dmidecode:
dmidecode: Handle 0x0005, DMI type 5, 23 bytes
dmidecode: Memory Controller Information
dmidecode: Error Detecting Method: None
dmidecode: Error Correcting Capabilities:
dmidecode: None
dmidecode: Supported Interleave: One-way Interleave
dmidecode: Current Interleave: One-way Interleave
dmidecode: Maximum Memory Module Size: 64 MB
dmidecode: Maximum Total Memory Size: 256 MB
dmidecode: Supported Speeds:
dmidecode: 70 ns
dmidecode: 60 ns
dmidecode: 50 ns
dmidecode: Supported Memory Types:
dmidecode: FPM
dmidecode: EDO
dmidecode: Parity
dmidecode: SIMM
dmidecode: Memory Module Voltage: 5.0 V
dmidecode: Associated Memory Slots: 4
dmidecode: 0x0006
dmidecode: 0x0007
dmidecode: 0x0008
dmidecode: 0x0009
dmidecode:
dmidecode: Handle 0x0007, DMI type 6, 12 bytes
dmidecode: Memory Module Information
dmidecode: Socket Designation: SIMM1&2-2
dmidecode: Bank Connections: 0 1
dmidecode: Current Speed: 70 ns
dmidecode: Type: FPM SIMM
dmidecode: Installed Size: Not Installed
dmidecode: Enabled Size: Not Installed
dmidecode: Error Status: OK
dmidecode:
dmidecode: Handle 0x0008, DMI type 6, 12 bytes
dmidecode: Memory Module Information
dmidecode: Socket Designation: SIMM3&4-1
dmidecode: Bank Connections: 2 3
dmidecode: Current Speed: 70 ns
dmidecode: Type: FPM SIMM
dmidecode: Installed Size: 32 MB (Single-bank Connection)
dmidecode: Enabled Size: 32 MB (Single-bank Connection)
dmidecode: Error Status: OK
dmidecode:
dmidecode: Handle 0x0009, DMI type 6, 12 bytes
dmidecode: Memory Module Information
dmidecode: Socket Designation: SIMM3&4-2
dmidecode: Bank Connections: 2 3
dmidecode: Current Speed: 70 ns
dmidecode: Type: FPM SIMM
dmidecode: Installed Size: Not Installed
dmidecode: Enabled Size: Not Installed
dmidecode: Error Status: OK
dmidecode:
dmidecode: Handle 0x000A, DMI type 7, 15 bytes
dmidecode: Cache Information
dmidecode: Socket Designation: L1 Cache
dmidecode: Configuration: Enabled, Not Socketed, Level 1
dmidecode: Operational Mode: Write Back
dmidecode: Location: Internal
dmidecode: Installed Size: 16 KB
dmidecode: Maximum Size: 16 KB
dmidecode: Supported SRAM Types: None
dmidecode: Installed SRAM Type: None
dmidecode:
dmidecode: Handle 0x000B, DMI type 7, 15 bytes
dmidecode: Cache Information
dmidecode: Socket Designation: L2 Cache
dmidecode: Configuration: Enabled, Not Socketed, Level 2
dmidecode: Operational Mode: Write Back
dmidecode: Location: External
dmidecode: Installed Size: 256 KB
dmidecode: Maximum Size: 512 KB
dmidecode: Supported SRAM Types:
dmidecode: Pipeline Burst
dmidecode: Installed SRAM Type: Asynchronous
dmidecode:
dmidecode: Handle 0x000C, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: COM1
dmidecode: Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
dmidecode: External Reference Designator: COM A
dmidecode: External Connector Type: DB-9 male
dmidecode: Port Type: Serial Port 16550A Compatible
dmidecode:
dmidecode: Handle 0x000D, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: COM2
dmidecode: Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
dmidecode: External Reference Designator: COM B
dmidecode: External Connector Type: DB-25 male
dmidecode: Port Type: Serial Port 16550A Compatible
dmidecode:
dmidecode: Handle 0x000E, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: PRINTER
dmidecode: Internal Connector Type: 25 Pin Dual Inline (pin 26 cut)
dmidecode: External Reference Designator: LPT
dmidecode: External Connector Type: DB-25 female
dmidecode: Port Type: Parallel Port ECP/EPP
dmidecode:
dmidecode: Handle 0x000F, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: KEY
dmidecode: Internal Connector Type: None
dmidecode: External Reference Designator: KEYBOARD
dmidecode: External Connector Type: Micro DIN
dmidecode: Port Type: Keyboard Port
dmidecode:
dmidecode: Handle 0x0010, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: PRIMARY IDE
dmidecode: Internal Connector Type: On Board IDE
dmidecode: External Reference Designator: IDE-1
dmidecode: External Connector Type: None
dmidecode: Port Type: None
dmidecode:
dmidecode: Handle 0x0011, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: SECONDARY IDE
dmidecode: Internal Connector Type: On Board IDE
dmidecode: External Reference Designator: IDE-2
dmidecode: External Connector Type: None
dmidecode: Port Type: None
dmidecode:
dmidecode: Handle 0x0012, DMI type 8, 9 bytes
dmidecode: Port Connector Information
dmidecode: Internal Reference Designator: FLOPPY
dmidecode: Internal Connector Type: On Board Floppy
dmidecode: External Reference Designator: FLOPPY
dmidecode: External Connector Type: None
dmidecode: Port Type: None
dmidecode:
dmidecode: Handle 0x0013, DMI type 9, 12 bytes
dmidecode: System Slot Information
dmidecode: Designation: PCI Slot1
dmidecode: Type: 32-bit PCI
dmidecode: Current Usage: Available
dmidecode: Length: Long
dmidecode: ID: 12
dmidecode: Characteristics:
dmidecode: 5.0 V is provided
dmidecode:
dmidecode: Handle 0x0014, DMI type 9, 12 bytes
dmidecode: System Slot Information
dmidecode: Designation: PCI Slot2
dmidecode: Type: 32-bit PCI
dmidecode: Current Usage: Available
dmidecode: Length: Short
dmidecode: ID: 11
dmidecode: Characteristics:
dmidecode: 5.0 V is provided
dmidecode:
dmidecode: Handle 0x0015, DMI type 9, 12 bytes
dmidecode: System Slot Information
dmidecode: Designation: PCI Slot3
dmidecode: Type: 32-bit PCI
dmidecode: Current Usage: Available
dmidecode: Length: Short
dmidecode: ID: 10
dmidecode: Characteristics:
dmidecode: 5.0 V is provided
dmidecode:
dmidecode: Handle 0x0016, DMI type 9, 12 bytes
dmidecode: System Slot Information
dmidecode: Designation: PCI Slot4
dmidecode: Type: 32-bit PCI
dmidecode: Current Usage: Available
dmidecode: Length: Long
dmidecode: ID: 9
dmidecode: Characteristics:
dmidecode: 5.0 V is provided
dmidecode: Opening is shared
dmidecode:
dmidecode: Handle 0x0017, DMI type 9, 12 bytes
dmidecode: System Slot Information
dmidecode: Designation: ISA Slot1
dmidecode: Type: 16-bit ISA
dmidecode: Current Usage: Unknown
dmidecode: Length: Long
dmidecode: Characteristics:
dmidecode: 5.0 V is provided
dmidecode: Opening is shared
dmidecode:
dmidecode: Handle 0x0018, DMI type 9, 12 bytes
dmidecode: System Slot Information
dmidecode: Designation: ISA Slot2
dmidecode: Type: 16-bit ISA
dmidecode: Current Usage: Unknown
dmidecode: Length: Long
dmidecode: Characteristics:
dmidecode: 5.0 V is provided
dmidecode:
dmidecode: Handle 0x0019, DMI type 9, 12 bytes
dmidecode: System Slot Information
dmidecode: Designation: ISA Slot3
dmidecode: Type: 16-bit ISA
dmidecode: Current Usage: Unknown
dmidecode: Length: Long
dmidecode: Characteristics:
dmidecode: 5.0 V is provided
dmidecode:
dmidecode: Handle 0x001A, DMI type 11, 5 bytes
dmidecode: OEM Strings
dmidecode: String 1: OEM String
dmidecode:
dmidecode: Handle 0x001B, DMI type 12, 5 bytes
dmidecode: System Configuration Options
dmidecode: Option 1: System String
dmidecode:
dmidecode: Handle 0x001C, DMI type 13, 22 bytes
dmidecode: BIOS Language Information
dmidecode: Installable Languages: 1
dmidecode: ENGLISH
dmidecode: Currently Installed Language: ENGLISH
dmidecode:
dmidecode: Handle 0x001D, DMI type 15, 20 bytes
dmidecode: System Event Log
dmidecode: Area Length: 4096 bytes
dmidecode: Header Start Offset: 0x0000
dmidecode: Header Length: 16 bytes
dmidecode: Data Start Offset: 0x0010
dmidecode: Access Method: Memory-mapped physical 32-bit address
dmidecode: Access Address: 0xFFFE8000
dmidecode: Status: Invalid, Not Full
dmidecode: Change Token: 0x00000000
dmidecode:
dmidecode: Wrong DMI structures count: 30 announced, only 29 decoded.
dmidecode: Wrong DMI structures length: 1015 bytes announced, structures occupy 1014 bytes.
==============================================
Installer status:
==============================================
Package: preseed-common
Status: install ok unpacked
Version: 1.26
Depends: cdebconf-udeb, di-utils (>= 1.14)
Description: common files for preseeding
Package: udpkg
Status: install ok unpacked
Version: 1.04
Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.41)
Description: tiny dpkg clone
Package: localechooser
Status: install ok installed
Version: 1.36
Depends: cdebconf-udeb, iso-3166-udeb, di-utils (>= 1.15)
Description: choose language/country/locale
Installer-Menu-Item: 10
Package: libnss-dns-udeb
Status: install ok unpacked
Version: 2.3.6.ds1-11
Description: GNU C Library: NSS helper for DNS - udeb
Package: lowmemcheck
Status: install ok unpacked
Version: 1.24
Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03)
Description: detect low-memory systems and enter lowmem mode
Package: main-menu
Status: install ok unpacked
Version: 1.17
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.47), cdebconf-udeb
Description: Debian installer main menu
Package: di-utils-shell
Status: install ok unpacked
Version: 1.44
Depends: cdebconf-udeb, di-utils (>= 1.18)
Description: Execute a shell
Installer-Menu-Item: 950
Package: di-utils
Status: install ok installed
Version: 1.44
Depends: libc6 (>= 2.3.6-6), libdebian-installer4-udeb (>= 0.47), cdebconf-udeb
Description: Miscellaneous utilities for the debian installer
Package: fb-modules-2.6.18-4-486-di
Status: install ok unpacked
Version: 1.43
Provides: fb-modules
Depends: kernel-image-2.6.18-4-486-di
Description: Frame buffer support
Package: kernel-image-2.6.18-4-486-di
Status: install ok unpacked
Version: 1.43
Provides: kernel-image, ext2-modules
Description: Linux kernel binary image for the Debian installer
Package: cdebconf-newt-udeb
Status: install ok unpacked
Version: 0.113
Depends: cdebconf-udeb, di-utils-terminfo, libc6 (>= 2.3.6-6), libnewt0.52
Description: Newt frontend for Debian Configuration Management System
Package: usb-modules-2.6.18-4-486-di
Status: install ok unpacked
Version: 1.43
Provides: usb-modules
Depends: kernel-image-2.6.18-4-486-di
Description: USB support
Package: module-init-tools-udeb
Status: install ok unpacked
Version: 3.3-pre4-1
Depends: libc6 (>= 2.3.6-6)
Description: tools for managing Linux kernel modules
Package: rootskel
Status: install ok installed
Version: 1.49
Depends: di-utils (>= 1.43), cdebconf-udeb
Description: Skeleton root filesystem used by debian-installer
Package: udev-udeb
Status: install ok unpacked
Version: 0.103-2
Depends: libc6 (>= 2.3.6-6)
Description: /dev/ and hotplug management daemon
Package: libtextwrap1-udeb
Status: install ok installed
Version: 0.1-5
Depends: libc6 (>= 2.3.6-6)
Description: text-wrapping library with i18n - runtime udeb
Package: usb-discover
Status: install ok unpacked
Version: 1.06
Depends: cdebconf-udeb
Description: Discover USB and load kernel modules
Package: rescue-check
Status: install ok unpacked
Version: 1.8
Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03), di-utils (>= 1.18)
Description: enter d-i rescue mode if requested
Package: nano-udeb
Status: install ok unpacked
Version: 2.0.3-1
Provides: editor
Depends: libc6 (>= 2.3.6-6), libslang2-udeb (>= 2.0.6-3)
Description: free Pico clone with some new features - tiny build
Package: cdebconf-udeb
Status: install ok installed
Version: 0.113
Provides: debconf-2.0
Depends: libc6 (>= 2.3.6-6), libdebian-installer4-udeb (>= 0.47), libtextwrap1-udeb
Description: Debian Configuration Management System (C-implementation)
Package: acpi-modules-2.6.18-4-486-di
Status: install ok unpacked
Version: 1.43
Provides: acpi-modules
Depends: kernel-image-2.6.18-4-486-di
Description: ACPI support modules
Package: iso-3166-udeb
Status: install ok installed
Version: 1.0a-1
Description: provides iso_3166.tab file
Package: floppy-retriever
Status: install ok installed
Version: 1.13
Provides: retriever
Depends: cdebconf-udeb, mountfloppy
Description: Fetches modules from a floppy
Package: busybox-udeb
Status: install ok unpacked
Version: 1:1.1.3-4
Depends: libc6 (>= 2.3.6-6)
Description: Tiny utilities for the debian-installer
Package: initrd-preseed
Status: install ok unpacked
Version: 1.26
Depends: preseed-common
Description: load debconf preseed file from /preseed.cfg on the initrd
Package: archdetect
Status: install ok installed
Version: 1.49
Depends: libc6 (>= 2.3.6-6), libdebian-installer4-udeb (>= 0.47)
Description: Hardware architecture detector
Package: load-floppy
Status: install ok installed
Version: 1.13
Depends: cdebconf-udeb, floppy-retriever, anna
Description: Load installer components from a floppy
Installer-Menu-Item: 11
Package: di-utils-reboot
Status: install ok unpacked
Version: 1.44
Depends: cdebconf-udeb
Description: Reboot
Installer-Menu-Item: 995
Package: anna
Status: install ok installed
Version: 1.26
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.47), cdebconf-udeb
Description: anna's not nearly apt, but for the Debian installer, it will do
Package: pciutils-udeb
Status: install ok unpacked
Version: 1:2.2.4-1
Depends: libc6 (>= 2.3.6-6), zlib1g-udeb (>= 1:1.2.1)
Description: Linux PCI Utilities (udeb)
Package: console-keymaps-at
Status: install ok installed
Version: 2:1.01-6
Provides: console-keymaps
Depends: cdebconf-udeb
Description: Keymaps for PC-style (PS/2 and AT) keyboards
Package: di-utils-terminfo
Status: install ok unpacked
Version: 1.44
Description: Terminfo entries needed by newt/slang in debian installer
Package: hw-detect
Status: install ok installed
Version: 1.49
Depends: rootskel (>= 1.30), archdetect, cdebconf-udeb (>= 0.75), di-utils (>= 1.26)
Description: Detect hardware and load kernel drivers for it
Package: kbd-chooser
Status: install ok installed
Version: 1.33
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.47), cdebconf-udeb, console-keymaps
Description: Detect a keyboard and select layout
Installer-Menu-Item: 12
Package: libdebian-installer4-udeb
Status: install ok installed
Version: 0.47
Depends: libc6 (>= 2.3.6-6)
Description: Library of common debian-installer functions
Package: installation-locale
Status: install ok unpacked
Version: 1.1
Depends: rootskel
Description: UTF-8 C locale
Package: env-preseed
Status: install ok unpacked
Version: 1.26
Description: debconf preseeding via environment variables
Package: mountfloppy
Status: install ok installed
Version: 0.10
Depends: cdebconf-udeb, di-utils (>= 1.15)
Description: Mounts a floppy
Package: cdebconf-priority
Status: install ok unpacked
Version: 0.113
Depends: cdebconf-udeb
Description: Change debconf priority
Installer-Menu-Item: 930
Package: zlib1g-udeb
Status: install ok unpacked
Version: 1:1.2.3-13
Provides: zlib1g
Description: compression library - runtime for Debian installer
Package: libdebconfclient0-udeb
Status: install ok installed
Version: 0.113
Depends: libc6 (>= 2.3.6-6), cdebconf-udeb
Description: Debian Configuration Management System (C-implementation)
Package: bogl-bterm-udeb
Status: install ok unpacked
Version: 0.1.18-1.5
Provides: editor
Depends: libc-udeb
Description: Ben's Own Graphics Library - graphical terminal
Package: input-modules-2.6.18-4-486-di
Status: install ok unpacked
Version: 1.43
Provides: input-modules
Depends: kernel-image-2.6.18-4-486-di, usb-modules-2.6.18-4-486-di
Description: Input devices support
Package: debian-installer
Status: install ok installed
Version: floppy-root-20070211-04:03
Description: debian installation image
Package: choose-mirror-bin
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 336
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 2.12
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.47), cdebconf-udeb
Description: Choose mirror to install from (program)
Package: choose-mirror
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 12
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 2.12
Depends: configured-network, choose-mirror-bin
Description: Choose mirror to install from (menu item)
Installer-Menu-Item: 23
Package: dhcp-client-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 132
Maintainer: Eloy A. Paris <peloy@debian.org>
Version: 2.0pl5-19.5
Depends: libc6 (>= 2.3.6-6)
Description: DHCP Client for debian-installer
dhcp-client-udeb is a minimal dhcp package used by the debian-installer.
Package: download-installer
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 20
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.13
Depends: cdebconf-udeb, net-retriever, anna (>= 1.07)
Description: Download installer components
Installer-Menu-Item: 23
Package: ethdetect
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 100
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.49
Depends: rootskel (>= 1.30), cdebconf-udeb (>= 0.38), hw-detect, di-utils (>= 1.13)
Provides: ethernet-card-detection
Description: Detect network hardware and load kernel drivers for it
Installer-Menu-Item: 17
Package: firewire-core-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 200
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: scsi-core-modules-2.6.18-4-486-di, kernel-image-2.6.18-4-486-di
Provides: firewire-core-modules
Description: Core FireWire drivers
This package contains core FireWire drivers for the Linux kernel.
Package: firmware-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 48
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: firmware-modules
Description: Firmware request modules
This package contains linux kernel modules that support requesting
external firmware.
Package: ipv6-modules-2.6.18-4-486-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 284
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: ipv6-modules
Description: IPv6 driver
This package contains the IPv6 driver for the Linux kernel.
Package: libiw28-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 24
Maintainer: Guus Sliepen <guus@debian.org>
Version: 28-1
Depends: libc6 (>= 2.3.5-1)
Description: Tools for manipulating Linux Wireless Extensions
This package contains the Wireless tools, used to manipulate the Linux
Wireless Extensions. The Wireless Extension is an interface allowing you to
set Wireless LAN specific parameters and get the specific stats.
.
This is a udeb of the wireless tools.
Package: libsysfs2-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 40
Maintainer: Martin Pitt <mpitt@debian.org>
Version: 2.1.0-1
Depends: libc6 (>= 2.3.6-6)
Provides: libsysfs2
Description: interface library to sysfs
Sysfs is a virtual file system in Linux kernel 2.5+ that provides a
tree of system devices. libsysfs provides a stable programming
interface to sysfs and eases querying system devices and their
attributes.
.
This is a minimal package for use in debian-installer.
Package: net-retriever
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 60
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.13
Depends: cdebconf-udeb, choose-mirror, configured-network, di-utils (>= 1.16)
Provides: retriever
Description: Fetch modules from the Internet
This is a retriever that uses wget to fetch files over http or ftp.
Package: netcfg
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 832
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.34
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.47), libiw28-udeb (>= 28), dhcp-client-udeb | dhcp3-client-udeb | pump-udeb, ethernet-card-detection
Provides: configured-network
Description: Configure the network
To install additional installer components or the Debian Base System over
the network, you need to configure the network in the installer. This
component will first try to configure your network with DHCP and ask
you for static network configuration if this fails. The configured
network settings will be copied to your newly installed system.
Installer-Menu-Item: 18
Package: network-preseed
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 40
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.26
Depends: cdebconf-udeb, configured-network, preseed-common
Description: download debconf preseed file
Installer-Menu-Item: 21
Package: nic-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 444
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, nic-shared-modules-2.6.18-4-486-di, firmware-modules-2.6.18-4-486-di, firewire-core-modules-2.6.18-4-486-di
Provides: nic-modules
Description: Common NIC drivers
This package contains common NIC drivers for the Linux kernel.
Package: nic-shared-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 52
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: nic-shared-modules
Description: Shared NIC drivers
This package contains NIC drivers needed by combinations of nic-modules,
nic-extra-modules, and nic-pcmcia-modules.
Package: nic-usb-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 208
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, nic-shared-modules-2.6.18-4-486-di, usb-modules-2.6.18-4-486-di, firmware-modules-2.6.18-4-486-di
Provides: nic-usb-modules
Description: USB NIC drivers
This package contains USB network adapter drivers for the Linux kernel.
Package: parport-modules-2.6.18-4-486-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 116
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: parport-modules
Description: Parallel port support
This package contains parallel port drivers for the Linux kernel.
Package: pcmcia-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 232
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, firmware-modules-2.6.18-4-486-di
Provides: pcmcia-modules
Description: Common PCMCIA drivers
This package contains common PCMCIA drivers for the Linux kernel.
Package: pcmciautils-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 96
Maintainer: Colin Watson <cjwatson@debian.org>
Version: 014-3
Depends: udev-udeb, libc6 (>= 2.3.6-6), libsysfs2-udeb
Description: PCMCIA utilities for Linux 2.6
This package provides PCMCIA initialisation tools for Linux 2.6.13-rc1 or
later, replacing the old pcmcia-cs tools used with earlier kernel versions.
PCMCIA cards are commonly used in laptops to provide expanded capabilities
such as network connections, modems, increased memory, etc.
.
To use PCMCIA you need to have kernel modules available to support it.
These are included in the stock Debian 2.6 kernel packages.
.
This is a minimal package for use in debian-installer.
Package: plip-modules-2.6.18-4-486-di
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 52
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, parport-modules-2.6.18-4-486-di
Provides: plip-modules
Description: PLIP drivers
This package contains PLIP drivers for the Linux kernel.
Package: scsi-core-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 240
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: scsi-core-modules
Description: Core SCSI subsystem
This package contains the core SCSI subsystem for the Linux kernel.
Package: wireless-tools-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 28
Maintainer: Guus Sliepen <guus@debian.org>
Version: 28-1
Depends: libc6 (>= 2.3.5-1), libiw28-udeb (>= 28)
Description: Tools for manipulating Linux Wireless Extensions
This package contains the Wireless tools, used to manipulate the Linux
Wireless Extensions. The Wireless Extension is an interface allowing you to
set Wireless LAN specific parameters and get the specific stats.
.
This is a udeb of the wireless tools.
Package: nic-extra-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 2992
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, nic-shared-modules-2.6.18-4-486-di, firmware-modules-2.6.18-4-486-di, crc-modules-2.6.18-4-486-di
Provides: nic-extra-modules
Description: Rare NIC drivers
This package contains rare NIC drivers for the Linux kernel.
Package: nic-pcmcia-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 572
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, nic-shared-modules-2.6.18-4-486-di, nic-extra-modules-2.6.18-4-486-di, pcmcia-modules-2.6.18-4-486-di
Provides: nic-pcmcia-modules
Description: Common PCMCIA NIC drivers
This package contains common PCMCIA NIC drivers for the Linux kernel.
Package: apt-mirror-setup
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 160
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.18
Depends: choose-mirror-bin, cdebconf-udeb
Description: set up a mirror in sources.list
Package: apt-setup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 104
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.18
Depends: apt-mirror-setup, base-installer (>= 1.49), cdebconf-udeb
Description: Configure apt
Installer-Menu-Item: 70
Package: base-installer
Status: install ok installed
Priority: required
Section: debian-installer
Installed-Size: 632
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.72
Depends: libc6 (>= 2.3.6-6), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.47), mounted-partitions, debootstrap-udeb (>= 0.3.1), created-fstab, archdetect, di-utils-mapdevfs, di-utils (>= 1.16), rootskel (>= 1.19)
Provides: kernel-installer
Description: Install the base system
Installer-Menu-Item: 65
Package: cdrom-core-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 140
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, scsi-core-modules-2.6.18-4-486-di, ide-modules-2.6.18-4-486-di
Provides: cdrom-core-modules
Description: CDROM support
This package contains core CDROM support for the Linux kernel.
Package: clock-setup
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 76
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.13
Depends: cdebconf-udeb, os-prober, tzsetup-udeb
Description: set up clock
Installer-Menu-Item: 62
Package: debootstrap-udeb
Status: install ok installed
Priority: required
Section: debian-installer
Installed-Size: 224
Maintainer: Anthony Towns <ajt@debian.org>
Version: 0.3.3.1
Depends: libc6 (>= 2.3.6-6), mounted-partitions
Description: Bootstrap the Debian system
debootstrap is used to create a Debian base system from scratch,
without requiring the availability of dpkg or apt. It does this by
downloading .deb files from a mirror site, and carefully unpacking them
into a directory which can eventually be chrooted into.
.
debootstrap-udeb is a minimal package used by debian-installer.
Package: di-utils-mapdevfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 16
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.44
Depends: libc6 (>= 2.3.6-6), libdebian-installer4-udeb (>= 0.47)
Description: mapdevfs utility for the debian installer
Package: disk-detect
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 64
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.49
Depends: cdebconf-udeb (>= 0.38), hw-detect, di-utils (>= 1.13)
Provides: harddrive-detection
Description: Detect disk drives
Installer-Menu-Item: 35
Package: dmidecode-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 64
Maintainer: Petter Reinholdtsen <pere@debian.org>
Version: 2.8-4
Depends: libc6 (>= 2.3.6-6)
Description: Dump Desktop Management Interface data (udeb)
Package: e2fsprogs-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 356
Maintainer: Theodore Y. Ts'o <tytso@mit.edu>
Version: 1.39+1.40-WIP-2006.11.14+dfsg-1
Depends: libblkid1-udeb, libc6 (>= 2.3.6-6)
Description: stripped-down versions of e2fsprogs, for debian-installer
This package is an e2fsprogs package built for a reduced size, so that
it can help to save space in debian-installer.
.
Don't attempt to install this package, it has no support for a couple of
features you surely want. Anyway it should refuse to install.
Package: efi-modules-2.6.18-4-486-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 44
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: efi-modules
Description: EFI modules
This package contains EFI modules.
Package: elilo-installer
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 100
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.9
Depends: cdebconf-udeb, base-installer, partconf-find-partitions (>= 1.08), di-utils-mapdevfs, fat-modules, efi-modules, dmidecode-udeb (>= 2.7)
Provides: bootable-system
Description: Install elilo on a hard disk
Installer-Menu-Item: 76
Package: ext3-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 240
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: ext3-modules
Description: EXT3 filesystem support
This package contains the EXT3 filesystem module for the Linux kernel.
Package: fat-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 132
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: fat-modules
Description: FAT filesystem support
This package contains the FAT and VFAT filesystem modules for the Linux kernel.
Package: fdisk-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 136
Maintainer: LaMont Jones <lamont@debian.org>
Version: 2.12r-18
Depends: libc6 (>= 2.3.6-6)
Description: Partition a hard drive (manual)
fdisk package
Package: finish-install
Status: install ok unpacked
Priority: required
Section: debian-installer
Installed-Size: 108
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 2.8
Depends: cdebconf-udeb, archdetect, base-installer, created-fstab, bootable-system
Provides: prebaseconfig
Description: Finish the installation and reboot
Installer-Menu-Item: 78
Package: floppy-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 104
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: floppy-modules
Description: Floppy driver
This package contains the floppy driver for the Linux kernel.
Package: grub-installer
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 376
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.21
Depends: cdebconf-udeb, kernel-installer, created-fstab, di-utils (>= 1.15), di-utils-mapdevfs, os-prober, dmidecode-udeb (>= 2.7)
Provides: bootable-system
Description: Install GRUB on a hard disk
Installer-Menu-Item: 73
Package: ide-core-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 144
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: ide-core-modules
Description: IDE support
This package contains core IDE support for the Linux kernel.
Package: ide-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 428
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, ide-core-modules-2.6.18-4-486-di
Provides: ide-modules
Description: IDE drivers
This package contains IDE drivers for the Linux kernel.
Package: jfs-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 216
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: jfs-modules
Description: JFS filesystem support
This package contains the JFS filesystem module for the Linux kernel.
Package: jfsutils-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 984
Maintainer: Stefan Hornburg (Racke) <racke@linuxia.de>
Version: 1.1.11-1
Depends: libc6 (>= 2.3.6-6), libuuid1-udeb
Description: A stripped-down version of jfsutils, for debian-installer
This package is a jfsutils package built for reduced size, so that it
can help to save space in debian-installer.
.
Don't attempt to install this package, it has no support for a couple of
features you surely want. Anyway, it should fail to install.
Package: libblkid1-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 40
Maintainer: Theodore Y. Ts'o <tytso@mit.edu>
Version: 1.39+1.40-WIP-2006.11.14+dfsg-1
Depends: libc6 (>= 2.3.6-6)
Provides: libblkid1
Description: block device id library
The blkid library which allows system programs like fsck and
mount to quickly and easily find block devices by filesystem UUID and
LABEL. This allows system administrators to avoid specifiying
filesystems by hard-coded device names, but via a logical naming
system instead.
.
This is a minimal package for debian-installer.
Package: libc6-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 1584
Maintainer: GNU Libc Maintainers <debian-glibc@lists.debian.org>
Version: 2.3.6.ds1-11
Provides: libc6, libc-udeb, glibc-2.3.6.ds1-1, glibc-2.3.6-2
Description: GNU C Library: Shared libraries - udeb
Contains the standard libraries that are used by nearly all programs on
the system. This package includes shared versions of the standard C library
and the standard math library, as well as many others.
.
This package contains a minimal set of libraries needed for the Debian
installer. Do not install it on a normal system.
Package: libdevmapper1.02-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 72
Maintainer: Debian LVM Team <pkg-lvm-maintainers@lists.alioth.debian.org>
Version: 2:1.02.12-1
Depends: libc6 (>= 2.3.6-6)
Provides: libdevmapper1.02
Description: The Linux Kernel Device Mapper userspace library
This is a udeb, or a microdeb, for the debian-installer.
.
The Linux Kernel Device Mapper is the LVM (Linux Logical Volume Management)
Team's implementation of a minimalistic kernel-space driver that handles
volume management, while keeping knowledge of the underlying device layout
in user-space. This makes it useful for not only LVM, but EVMS, software
raid, and other drivers that create "virtual" block devices.
Package: libparted1.7-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 340
Maintainer: Parted Maintainer Team <parted-maintainers@lists.alioth.debian.org>
Version: 1.7.1-5
Depends: libc6 (>= 2.3.6-6), libuuid1-udeb
Provides: libparted1.7-1
Description: The GNU Parted disk partitioning shared library
GNU Parted is a program that allows you to create, destroy,
resize, move and copy hard disk partitions. This is useful
for creating space for new operating systems, reorganising
disk usage, and copying data to new hard disks. This package
contains the Parted binary and manual page.
.
This package contains libparted, the required shared library
used by Parted. This is a cut-down package with no normal
documentation intended to be used in debian-installer.
.
Parted currently supports DOS, Mac, Sun, BSD, GPT, MIPS and
PC98 disklabels/partition tables, as well as a 'loop' (raw
disk) type which allows use on RAID/LVM. Filesystems which
are currently fully supported are ext2, ext3, fat (FAT16
and FAT32), ReiserFS (with libreiserfs) and linux-swap.
Parted can also detect and remove HFS (Mac OS), JFS, NTFS,
UFS (Sun and HP), XFS and ASFS/AFFS/APFS (Amiga) filesystems,
but cannot create, resize or check these filesystems yet.
.
Note that ReiserFS support is only enabled if you install
the libreiserfs0.3-0 package. Since libreiserfs0.3-0 has been
removed from sarge, ReiserFS support is not compiled in the
default package.
.
The nature of this software means that any bugs could cause
massive data loss. While there are no known bugs at the moment,
they could exist, so please back up all important files before
running it, and do so at your own risk.
Package: libuuid1-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 24
Maintainer: Theodore Y. Ts'o <tytso@mit.edu>
Version: 1.39+1.40-WIP-2006.11.14+dfsg-1
Depends: libc6 (>= 2.3.6-6)
Provides: libuuid1
Description: universally unique id library
libuuid generates and parses 128-bit universally unique id's (UUID's).
See RFC 4122 for more information.
.
This is a minimal package for debian-installer.
Package: lilo-installer
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 232
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.19
Depends: cdebconf-udeb, kernel-installer, di-utils (>= 1.15), di-utils-mapdevfs, fdisk-udeb, os-prober, dmidecode-udeb (>= 2.7)
Provides: bootable-system
Description: Install LILO on a hard disk
Installer-Menu-Item: 75
Package: loop-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 52
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: loop-modules
Description: Loopback filesystem support
This package contains loopback filesystem support for the Linux kernel.
Package: lowmem
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 32
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.24
Description: free memory for lowmem install
Installer-Menu-Item: 25
Package: lvm2-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 428
Maintainer: Debian LVM Team <pkg-lvm-maintainers@lists.alioth.debian.org>
Version: 2.02.06-3
Depends: libc6 (>= 2.3.6-6), libdevmapper1.02-udeb (>= 2:1.02.02-2)
Description: The Linux Logical Volume Manager
This is a udeb, or a microdeb, for the debian-installer.
.
This is LVM2, the rewrite of The Linux Logical Volume Manager. LVM
supports enterprise level volume management of disk and disk subsystems
by grouping arbitrary disks into volume groups. The total capacity of
volume groups can be allocated to logical volumes, which are accessed as
regular block devices.
Package: md-modules-2.6.18-4-486-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 436
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: md-modules
Description: RAID and LVM support
This package contains RAID and LVM modules for the Linux kernel.
Package: mdadm-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 176
Maintainer: Debian mdadm maintainers <pkg-mdadm-devel@lists.alioth.debian.org>
Version: 2.5.6-8
Depends: libc6 (>= 2.3.6-6)
Description: tool to administer Linux MD arrays (software RAID)
mdadm is a program that can be used to create, manage, and monitor MD
arrays (e.g. software RAID, multipath devices).
.
mdadm-udeb is a minimal package used by the debian-installer.
Package: mdcfg-utils
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 408
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.20
Depends: cdebconf-udeb, di-utils (>= 1.16), md-modules, mdadm-udeb (>= 2.5.2), partconf-find-partitions
Description: Configure MD devices
Use this module to configure the MD devices.
Package: mkreiserfs-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 144
Maintainer: Ed Boraas <ed@debian.org>
Version: 1:3.6.19-4
Depends: libc6 (>= 2.3.6-6), libuuid1-udeb
Description: User-level tools for ReiserFS filesystems
This installer module contains the utility to create ReiserFS filesystems.
.
Homepage: http://www.namesys.com/
Package: nobootloader
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 168
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.16
Depends: cdebconf-udeb, base-installer (>= 1.23), di-utils-mapdevfs
Provides: bootable-system
Description: Don't install any bootloader.
This package will skip installing a boot-loader
Installer-Menu-Item: 77
Package: ntfsprogs-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 244
Maintainer: David Mart?nez Moreno <ender@debian.org>
Version: 1.13.1-6
Depends: libc6 (>= 2.3.6-6)
Provides: ntfstools-udeb
Description: Tools for doing neat things in NTFS partitions from Linux - udeb
Currently this udeb contains only ntfsresize.
Package: os-prober-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 128
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.15
Depends: di-utils-mapdevfs, anna (>= 1.16)
Provides: os-prober
Description: utility to detect other OSes on a set of drives
This package is to be used by boot loader installers to detect other OSes
available on a system, in a generic format, which it can then adapt to its
own configuration format.
Package: partconf-find-partitions
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 32
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.20
Depends: libc6 (>= 2.3.6-6), libdebian-installer4-udeb (>= 0.47), libparted1.7-udeb (>= 1.7.1-1)
Description: debian-installer utility for finding partitions
Helper program for finding partitions and detecting their size and
existing file system.
Package: parted-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 68
Maintainer: Parted Maintainer Team <parted-maintainers@lists.alioth.debian.org>
Version: 1.7.1-5
Depends: libc6 (>= 2.3.6-6), libparted1.7-udeb (>= 1.7.1-1)
Provides: parted
Description: The GNU Parted disk partition resizing program
GNU Parted is a program that allows you to create, destroy,
resize, move and copy hard disk partitions. This is useful
for creating space for new operating systems, reorganising
disk usage, and copying data to new hard disks. This package
contains the Parted binary and manual page.
.
This package is similar to the "big" parted package, but has
less cosmetical features resulting in smaller binary. Intended
to be used in debian-installer.
.
.
The nature of this software means that any bugs could cause
massive data loss. While there are no known bugs at the moment,
they could exist, so please back up all important files before
running it, and do so at your own risk.
Package: partman-auto
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 388
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 66
Depends: cdebconf-udeb, di-utils, partman-base (>= 99), partman-basicfilesystems, partman-ext3
Description: Automatically partition storage devices (partman)
Package: partman-auto-crypto
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 48
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 4
Depends: cdebconf-udeb, partman-auto (>= 55), partman-auto-lvm (>= 14), partman-crypto (>= 13), partman-base (>= 87)
Description: Automatically partition storage devices using crypto and LVM
Package: partman-auto-lvm
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 164
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 21
Depends: cdebconf-udeb, partman-base (>= 73), partman-auto (>= 59), partman-lvm (>= 36), di-utils (>= 1.15), lvm2-udeb
Description: Automatically partition storage devices using LVM
Package: partman-auto-raid
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 68
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 4
Depends: cdebconf-udeb, partman-base (>= 99), partman-basicfilesystems, partman-ext3, partman-auto (>= 58), partman-md
Description: Allow preseeded RAID installs
Package: partman-base
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 872
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 103
Depends: libc6 (>= 2.3.6-6), libparted1.7-udeb (>= 1.7.1-1), cdebconf-udeb, partman-partitioning, partman-target, archdetect, harddrive-detection, di-utils-mapdevfs, di-utils (>= 1.15)
Provides: made-filesystems, mounted-partitions, partitioned-harddrives, created-fstab
Description: Partition the storage devices (partman)
Installer-Menu-Item: 42
Package: partman-basicfilesystems
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 600
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 51
Depends: cdebconf-udeb, e2fsprogs-udeb, ext2-modules, fat-modules, di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add to partman support for ext2, linux-swap, fat16 and fat32
Package: partman-basicmethods
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 132
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 33
Depends: cdebconf-udeb
Provides: partman-method
Description: Basic partition usage methods for partman
This package provides partman with two methods to use partitions.
The first is to format the partition. The second is to keep and use
the existing data in the partition as it is.
Package: partman-crypto
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 880
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 19
Depends: partman-base (>= 87), libc6 (>= 2.3.6-6), cdebconf-udeb
Description: Add to partman support for block device encryption
Package: partman-efi
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 136
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 12
Depends: partman-base, efi-modules
Description: Add to partman support for EFI boot partitions
Package: partman-ext3
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 228
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 45
Depends: cdebconf-udeb, e2fsprogs-udeb, ext3-modules, partman-basicfilesystems, di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add to partman support for ext3
Package: partman-jfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 272
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 20
Depends: cdebconf-udeb, jfsutils-udeb, jfs-modules, partman-basicfilesystems, di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add support for jfs to partman
Package: partman-lvm
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 732
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 50
Depends: cdebconf-udeb, partman-base (>= 87), di-utils (>= 1.14), md-modules, lvm2-udeb, parted-udeb
Description: Adds support for LVM to partman
Package: partman-md
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 160
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 31
Depends: cdebconf-udeb, mdadm-udeb, mdcfg-utils, partman-base (>= 87)
Description: Add to partman support for MD
Package: partman-partitioning
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 380
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 45
Depends: ntfsprogs-udeb, cdebconf-udeb
Description: Partitioning operations for partman
This udeb provides partman with editing operations for creation
of new partitions, deletion of partitions and initialisation of the
partition table.
Package: partman-reiserfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 236
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 34
Depends: cdebconf-udeb, mkreiserfs-udeb, reiserfs-modules, partman-basicfilesystems, di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add to partman support for reiserfs
Package: partman-target
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 320
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 47
Depends: cdebconf-udeb, partman-basicfilesystems, partman-basicmethods, di-utils-mapdevfs
Description: Provides partman with ability to prepare /target
This udeb allows the user to choose how partitions should be used.
Package: partman-xfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 224
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 32
Depends: cdebconf-udeb, xfsprogs-udeb, xfs-modules, partman-basicfilesystems, di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add to partman support for xfs
Package: pcmcia-storage-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 52
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, ide-core-modules-2.6.18-4-486-di, cdrom-core-modules-2.6.18-4-486-di, pcmcia-modules-2.6.18-4-486-di
Provides: pcmcia-storage-modules
Description: PCMCIA storage drivers
This package contains PCMCIA storage drivers for the Linux kernel.
Package: pkgsel
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 32
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.11
Depends: cdebconf-udeb, apt-setup-udeb, di-utils (>= 1.20)
Description: Select and install packages
Installer-Menu-Item: 70
Package: reiserfs-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 268
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: reiserfs-modules
Description: Reiser filesystem support
This package contains the Reiser filesystem module for the Linux kernel.
Package: sata-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 404
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, scsi-core-modules-2.6.18-4-486-di
Provides: sata-modules
Description: SATA drivers
This package contains SATA drivers for the Linux kernel.
Package: save-logs
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 192
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 2.28
Depends: cdebconf-udeb
Description: save logs and configuration for debug purposes
Installer-Menu-Item: 940
Package: scsi-common-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 704
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, scsi-core-modules-2.6.18-4-486-di, cdrom-core-modules-2.6.18-4-486-di
Provides: scsi-common-modules
Description: Very common SCSI drivers
This package contains very common SCSI drivers for the Linux kernel.
Package: scsi-extra-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 1388
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: scsi-modules-2.6.18-4-486-di, scsi-core-modules-2.6.18-4-486-di
Provides: scsi-extra-modules
Description: Uncommon SCSI drivers
This package contains uncommon SCSI drivers for the Linux kernel.
This includes SCSI RAID drivers, and some of the less common SCSI
controllers.
Package: scsi-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 1040
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di, scsi-core-modules-2.6.18-4-486-di, parport-modules-2.6.18-4-486-di, cdrom-core-modules-2.6.18-4-486-di, firmware-modules-2.6.18-4-486-di
Provides: scsi-modules
Description: SCSI drivers
This package contains SCSI drivers for the Linux kernel.
Package: tzsetup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 304
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.15
Depends: cdebconf-udeb, localechooser
Description: choose timezone
Installer-Menu-Item: 62
Package: usb-storage-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 136
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: ide-core-modules-2.6.18-4-486-di, scsi-core-modules-2.6.18-4-486-di, usb-modules-2.6.18-4-486-di
Provides: usb-storage-modules
Description: USB storage support
This package contains the USB storage driver for the Linux kernel.
Package: user-setup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 360
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.10
Depends: cdebconf-udeb
Description: Set up users and passwords
Installer-Menu-Item: 63
Package: xfs-modules-2.6.18-4-486-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 552
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: xfs-modules
Description: XFS filesystem support
This package contains the XFS filesystem module for the Linux kernel.
Package: xfsprogs-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 240
Maintainer: Nathan Scott <nathans@debian.org>
Version: 2.8.18-1
Depends: libc6 (>= 2.3.6-6), libuuid1-udeb
Description: A stripped-down version of xfsprogs, for debian-installer
This package is an xfsprogs package built for reduced size, so that it
can help to save space in debian-installer.
.
Don't attempt to install this package, it has no support for a couple of
features you surely want. Anyway, it should fail to install.
Package: ntfs-modules-2.6.18-4-486-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 248
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: ntfs-modules
Description: NTFS filesystem support
This package contains the NTFS file system module for the Linux kernel.
Package: qnx4-modules-2.6.18-4-486-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 48
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: kernel-image-2.6.18-4-486-di
Provides: qnx4-modules
Description: QNX4 filesystem support
This package contains the QNX4 filesystem module for the Linux kernel.
-- System Information:
Debian Release: 4.0
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i586)
Shell: /bin/sh linked to /bin/bash
Kernel: Linux 2.6.18-3-486
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
installation-report depends on no packages.
Versions of packages installation-report recommends:
ii pciutils 1:2.2.4~pre4-1 Linux PCI Utilities
ii reportbug 3.31 reports bugs in the Debian distrib
-- no debconf information
Reply to: