--- Begin Message ---
Package: installation-reports
Boot method: CD
Image version: http://cdimage.debian.org/cdimage/daily-builds/daily/arch-latest/powerpc/iso-cd/debian-testing-powerpc-netinst.iso
Date: Wed Feb 14 14:30:35 EST 2007
Machine: IBM 44P 7044-170
Processor: POWER3 (630+) -- ppc64
Memory: 1024MB
Partitions:
Filesystem Type 1K-blocks Used Available Use% Mounted on
/dev/sda2 ext3 16848312 675604 15316848 5% /
tmpfs tmpfs 497280 0 497280 0% /lib/init/rw
udev tmpfs 10240 48 10192 1% /dev
tmpfs tmpfs 497280 0 497280 0% /dev/shm
/dev/sdb1 ext3 17639220 176496 16566704 2% /home
Output of lspci -nn and lspci -vnn:
0000:00:0b.0 ISA bridge [0601]: Symphony Labs W83C553 [10ad:0565] (rev 10)
0000:00:0c.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic
53C896/897 [1000:000b] (rev 07)
0000:00:0c.1 SCSI storage controller [0100]: LSI Logic / Symbios Logic
53C896/897 [1000:000b] (rev 07)
0000:00:0f.0 Ethernet controller [0200]: Advanced Micro Devices [AMD]
79c970 [PCnet32 LANCE] [1022:2000] (rev 26)
0000:00:10.0 Ethernet controller [0200]: Advanced Micro Devices [AMD]
79c970 [PCnet32 LANCE] [1022:2000] (rev 26)
0001:40:0b.0 VGA compatible controller [0300]: IBM GXT 3000P
[1014:0090] (rev 02)
0000:00:0b.0 ISA bridge [0601]: Symphony Labs W83C553 [10ad:0565] (rev 10)
Flags: bus master, medium devsel, latency 0
0000:00:0c.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic
53C896/897 [1000:000b] (rev 07)
Subsystem: LSI Logic / Symbios Logic LSI53C896/7 PCI to Dual
Channel Ultra2 SCSI Multifunction Controller [1000:1000] Flags:
bus master, medium devsel, latency 72, IRQ 17
I/O ports at f8fff800 [size=256]
Memory at c0205000 (64-bit, non-prefetchable) [size=1K]
Memory at c0202000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
0000:00:0c.1 SCSI storage controller [0100]: LSI Logic / Symbios Logic
53C896/897 [1000:000b] (rev 07)
Subsystem: LSI Logic / Symbios Logic LSI53C896/7 PCI to Dual
Channel Ultra2 SCSI Multifunction Controller [1000:1000] Flags:
bus master, medium devsel, latency 72, IRQ 18
I/O ports at f8fffc00 [size=256]
Memory at c0204000 (64-bit, non-prefetchable) [size=1K]
Memory at c0200000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
0000:00:0f.0 Ethernet controller [0200]: Advanced Micro Devices [AMD]
79c970 [PCnet32 LANCE] [1022:2000] (rev 26)
Flags: bus master, medium devsel, latency 72, IRQ 19
I/O ports at f8fff000 [size=32]
Memory at c0207000 (32-bit, non-prefetchable) [size=32]
Expansion ROM at c0100000 [disabled] [size=1M]
0000:00:10.0 Ethernet controller [0200]: Advanced Micro Devices [AMD]
79c970 [PCnet32 LANCE] [1022:2000] (rev 26)
Flags: bus master, medium devsel, latency 72, IRQ 20
I/O ports at f8fff400 [size=32]
Memory at c0206000 (32-bit, non-prefetchable) [size=32]
Expansion ROM at c0000000 [disabled] [size=1M]
0001:40:0b.0 VGA compatible controller [0300]: IBM GXT 3000P
[1014:0090] (rev 02) (prog-if 00 [VGA])
Subsystem: IBM GXT-3000P [1014:008e]
Flags: bus master, 66MHz, medium devsel, latency 72, IRQ 29
Memory at dbf80000 (32-bit, non-prefetchable) [size=512K]
Memory at dc000000 (32-bit, non-prefetchable) [size=64M]
Expansion ROM at dbf40000 [disabled] [size=256K]
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [O]
Configure network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [O]
Install boot loader: [O]
Overall install: [O]
Comments/Problems:
The graphics card (IBM GXT-3000P) isn't well supported in Linux, so I
had to use a serial console. The installer's refresh rate was very
slow over a serial connection (it takes more than a second to draw
each screen). Other than that minor annoyance, everything went
smoothly. Great work!
--- End Message ---
--- Begin Message ---
On Wednesday 14 February 2007 20:41, Thomas Cort wrote:
> Comments/Problems:
> The graphics card (IBM GXT-3000P) isn't well supported in Linux, so I
> had to use a serial console. The installer's refresh rate was very
> slow over a serial connection (it takes more than a second to draw
> each screen). Other than that minor annoyance, everything went
> smoothly. Great work!
Next time try using the network-console module. This will allow you to run
most of the installation over an SSH session, which is much faster.
You can use this by booting the installer with "modules=network-console".
Closing this report as the installation was successful. Thank you for
submitting it.
Cheers,
FJP
--- End Message ---