Bug#395267: installation-reports
Package: installation-reports
Boot method: USB-Stick
Image version: businesscard image of 21.10.06,
http://cdimage.debian.org/cdimage/daily-builds/daily/arch-latest/i386/iso-cd/debian-testing-i386-businesscard.iso
Date: 21.10.06, around noon GMT
Machine: Dell Inspiron 6400
Processor: Intel(R) Core(TM)2 CPU T7200 @ 2.00GHz
Memory: 2G 667Mhz DDR2
Partitions:
Disk /dev/sda: 118.5 GB, 118526284800 bytes
255 heads, 63 sectors/track, 14410 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 3824 30716248+ 7 HPFS/NTFS
/dev/sda2 3825 4067 1951897+ 82 Linux swap /
Solaris
/dev/sda3 4068 5040 7815622+ 83 Linux
/dev/sda4 5041 14410 75264525 83 Linux
Output of lspci and lspci -n:
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and
945GT Express Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT
Express PCI Express Root Port (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High
Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 1 (rev 01)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 4 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1
(rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2
(rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3
(rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4
(rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial
ATA Storage Controller IDE (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller
(rev 01)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility
X1400
03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX
(rev 02)
03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
03:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822
SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
03:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host
Adapter (rev 0a)
03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
0b:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network
Connection (rev 02)
00:00.0 0600: 8086:27a0 (rev 03)
00:01.0 0604: 8086:27a1 (rev 03)
00:1b.0 0403: 8086:27d8 (rev 01)
00:1c.0 0604: 8086:27d0 (rev 01)
00:1c.3 0604: 8086:27d6 (rev 01)
00:1d.0 0c03: 8086:27c8 (rev 01)
00:1d.1 0c03: 8086:27c9 (rev 01)
00:1d.2 0c03: 8086:27ca (rev 01)
00:1d.3 0c03: 8086:27cb (rev 01)
00:1d.7 0c03: 8086:27cc (rev 01)
00:1e.0 0604: 8086:2448 (rev e1)
00:1f.0 0601: 8086:27b9 (rev 01)
00:1f.2 0101: 8086:27c4 (rev 01)
00:1f.3 0c05: 8086:27da (rev 01)
01:00.0 0300: 1002:7145
03:00.0 0200: 14e4:170c (rev 02)
03:01.0 0c00: 1180:0832
03:01.1 0805: 1180:0822 (rev 19)
03:01.2 0880: 1180:0843 (rev 01)
03:01.3 0880: 1180:0592 (rev 0a)
03:01.4 0880: 1180:0852 (rev 05)
0b:00.0 0280: 8086:4222 (rev 02)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
Very nice work!
I did expertgui mode. The only thing I missed was some more feedback from
the install process besides the nice waitbar. I guess I could have
switched on a debug mode, but when I noticed it, the install process was
already running.
One strange thing happened: I told the system not to use UTC (because of
Windows), but when I bootet the first time, the time was set two hours
early (which is the +2 hours difference of my local time to UTC). I set it
back during a Windows session, at the next Debian boot everything was ok.
I got the "select() to /dev/rtc to wait for clock tick timed out" problem
and fixed it with HWCLOCKPARS=--directisa for now. I guess that's not an
installer problem itself (and the fix is probably just a workaround!?).
Regards,
Tilo
Reply to: