Bug#381135: crypto installs in german, french, spanish
Package: installation-reports
Boot method: businesscard ISO
Image version: 2006-07-31 build from
http://cdimage.debian.org/cdimage/daily-builds/daily/arch-latest/i386/iso-cd/debian-testing-i386-businesscard.iso
Machine: Custom-built (ASUS A7V)
Processor: AMD Athlon 700
Memory: 1 GB
Partitions:
Filesystem Type 1K-blocks Used Available Use% Mounted on
/dev/hdc1 ext3 730120 372394 318770 54% /
tmpfs tmpfs 518028 0 518028 0% /dev/shm
/dev/hdc2 ext3 90329 4133 81377 5% /home
tmpfs tmpfs 10240 92 10148 1% /dev
# /etc/fstab: static file system information.
#
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc defaults 0 0
/dev/hdc1 / ext3 defaults,errors=remount-ro 0 1
/dev/hdc2 /home ext3 defaults,loop=/dev/loop0,encryption=AES256,gpgkey=/etc/loopkeys/_dev_hdc2.gpg 0 0
/dev/hdc3 none swap sw,loop=/dev/loop1,encryption=AES256 0 0
/dev/hda /media/cdrom0 udf,iso9660 user,noauto 0 0
/dev/fd0 /media/floppy0 auto rw,user,noauto 0 0
losetup -a:
/dev/loop/0: [000c]:4503 (/dev/hdc2) encryption=AES256 multi-key-v3
/dev/loop1: [000c]:4515 (/dev/hdc3) offset=4096 encryption=AES256 multi-key-v3
/proc/swaps:
Filename Type Size Used Priority
/dev/loop1 partition 176700 0 -1
Output of lspci:
lspci -v -t: -[0000:00]-+-00.0 VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
lspci -v -t: +-01.0-[0000:01]----00.0 Matrox Graphics, Inc. G400/G450
lspci -v -t: +-04.0 VIA Technologies, Inc. VT82C686 [Apollo Super South]
lspci -v -t: +-04.1 VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE
lspci -v -t: +-04.2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
lspci -v -t: +-04.3 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
lspci -v -t: +-04.4 VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
lspci -v -t: +-0a.0 Brooktree Corporation Bt848 Video Capture
lspci -v -t: +-0b.0 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
lspci -v -t: +-0c.0 Ensoniq 5880 AudioPCI
lspci -v -t: \-11.0 Promise Technology, Inc. PDC20265 (FastTrak100 Lite/Ultra100)
lspci -n: 00:00.0 0600: 1106:0305 (rev 02)
lspci -n: 00:01.0 0604: 1106:8305
lspci -n: 00:04.0 0601: 1106:0686 (rev 22)
lspci -n: 00:04.1 0101: 1106:0571 (rev 10)
lspci -n: 00:04.2 0c03: 1106:3038 (rev 10)
lspci -n: 00:04.3 0c03: 1106:3038 (rev 10)
lspci -n: 00:04.4 0600: 1106:3057 (rev 30)
lspci -n: 00:0a.0 0400: 109e:0350 (rev 12)
lspci -n: 00:0b.0 0200: 10ec:8139 (rev 10)
lspci -n: 00:0c.0 0401: 1274:5880 (rev 02)
lspci -n: 00:11.0 0180: 105a:0d30 (rev 02)
lspci -n: 01:00.0 0300: 102b:0525 (rev 04)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
I'm actually reporting about three installs, all focused on
testing partman-crypto in different languages (german, spanish,
french). They were all done on the same system.
The tasks in tasksel ("Desktop environment", ..) were not
translated into the respective languages but shown in english.
I think in previous installs they used to be translated. Other
than that the translations looked fine from what I could tell
with my limited knowledge of spanish and french :-)
I also noticed one thing related to wiping partitions in
preparation of encryption: The progressbar shown while
blockdev-wipe runs was wildly inaccurate. It proceeded to 100%
very quickly and then remained there for close to ten seconds.
Overall the wipe seemed to complete too quickly compared the
speed that this old harddisk is capable of (~3MB/s). I'll
reassign this to partman-crypto and investigate.
cheers,
Max
Reply to: