Bug#380579: (no subject)
Package: installation-reports
INSTALL REPORT
Debian-installer-version: < Debian GNU/Linux 3.1 r0a "Sarge" -
Official i386 Binary-1 (20050607);downloaded by jigdo~2 mo's after Sarge
release >
uname -a: < Linux osprey.cowpie 2.6.8-2-386 #1 Thu May 19 17:40:50
JST 2005 i686 GNU/Linux
>
Date: <installed numerous times;most recent ~july 06 >
Method: How did you install? What did you boot off? If network
install, from where? Proxied? cdrom
Machine: <Toshiba M500>
Processor:pentium II
Memory:256 M
Root Device: <hda: WDC WD102AA, ATA DISK drive0000:00:00.0 Host bridge:
Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (r
ev 03)
>
Root Size/partition table: Feel free to paste the full partition
table, with notes on which partitions are mounted where.
osprey:/proc# cat partitions
major minor #blocks name
3 0 10022040 hda
3 1 5012248 hda1
3 2 5004247 hda2
3 64 10022040 hdb
3 65 5012248 hdb1
3 66 1 hdb2
3 69 2498076 hdb5
3 70 248976 hdb6
3 71 2257101 hdb7
Output of lspci and lspci -n:
0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP
bridge (rev
03)
0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
0000:00:08.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 04)
0000:00:09.0 FireWire (IEEE 1394): Lucent Microelectronics FW323 (rev 04)
0000:01:00.0 VGA compatible controller: Intel Corp. 82740 (i740) AGP
Graphics Ac
celerator (rev 21)
osprey:~# lspci -n
0000:00:00.0 0600: 8086:7190 (rev 03)
0000:00:01.0 0604: 8086:7191 (rev 03)
0000:00:07.0 0601: 8086:7110 (rev 02)
0000:00:07.1 0101: 8086:7111 (rev 01)
0000:00:07.2 0c03: 8086:7112 (rev 01)
0000:00:07.3 0680: 8086:7113 (rev 02)
0000:00:08.0 0401: 1274:5880 (rev 04)
0000:00:09.0 0c00: 11c1:5811 (rev 04)
0000:01:00.0 0300: 8086:7800 (rev 21)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [0]
Detect hard drives: [0]
Partition hard drives: [0]
Create file systems: [O]
Mount partitions: [0]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:I had a problem with the cdrom hanging
during tasksel; I went to another terminal ran telinit 1 to
unhang the cdrom and returned to the install ok. I'm not
sure if this is hardware or software.
<Description of the install, in prose, and any thoughts, comments
and ideas you had during the initial install.>
The installer was very different from Woody but after a few
installs I came to appreciate it. The guided partitioning is
a nice touch and I used it to install the 2.4 kernel on an
old IBM Aptiva to use as a Samba server .I also have the
2.4 installation on the gateway machine (an unknown
throwtogether with a k6-II processor) with wwwoffle and
shorewall installed and finally the Woody 2.2 on a 486
machine as an intranet webserver . All these machines were
given to me and I obtained debian with jigdo, the total
cost of my home network is zero!
Install logs and other status info is available in
/var/log/debian-installer/.
Once you have filled out this report, mail it to submit@bugs.debian.org.
_________________________________________________________________
Is your PC infected? Get a FREE online computer virus scan from McAfee®
Security. http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963
Reply to: