Bug#317452: installation-reports: Serial ATA hard disk
Package: installation-reports
Debian-installer-version: Today downloaded image. URL:
http://cdimage.debian.org/pub/cdimage-testing/daily/i386/20050706/debian-testing-i386-netinst.iso
uname -a: Linux dhcppc7 2.6.8-2-386 #1 Thu May 19 17:40:50 JST 2005 i686 GNU/Linux
Date: fri 8 july 2005, 18:20
Method:
I'd used netinstall image.
On boot selected mode: expert26
Other packages intalled from ftp.uk.debian.org (testing)
No proxy
Machine: Clone
Processor: Pentium IV
Memory: 1 GB Kignston
Root Device: 120 GB Serial Ata
Root Size/partition table:
Device Boot Start End Blocks Id System
/dev/sda1 * 1 851 6835626 83 Linux
/dev/sda2 852 14596 110406712+ 5 Extended
/dev/sda5 852 1181 2650693+ 82 Linux swap
/dev/sda6 1182 14596 107755956 83 Linux
Output of lspci :
0000:00:00.0 Host bridge: Intel Corp. 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
0000:00:01.0 PCI bridge: Intel Corp. 82865G/PE/P PCI to AGP Controller (rev 02)
0000:00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1 (rev 02)
0000:00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2 (rev 02)
0000:00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3 (rev 02)
0000:00:1d.3 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4 (rev 02)
0000:00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2)
0000:00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Bridge (rev 02)
0000:00:1f.2 IDE interface: Intel Corp. 82801EB (ICH5) Serial ATA 150 Storage Controller (rev 02)
0000:00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device 4153
0000:01:00.1 Display controller: ATI Technologies Inc: Unknown device 4173
0000:02:09.0 Ethernet controller: Marvell Technology Group Ltd. Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (rev 13)
Output of lspci -n:
0000:00:00.0 0600: 8086:2570 (rev 02)
0000:00:01.0 0604: 8086:2571 (rev 02)
0000:00:1d.0 0c03: 8086:24d2 (rev 02)
0000:00:1d.1 0c03: 8086:24d4 (rev 02)
0000:00:1d.2 0c03: 8086:24d7 (rev 02)
0000:00:1d.3 0c03: 8086:24de (rev 02)
0000:00:1d.7 0c03: 8086:24dd (rev 02)
0000:00:1e.0 0604: 8086:244e (rev c2)
0000:00:1f.0 0601: 8086:24d0 (rev 02)
0000:00:1f.2 0101: 8086:24d1 (rev 02)
0000:00:1f.3 0c05: 8086:24d3 (rev 02)
0000:00:1f.5 0401: 8086:24d5 (rev 02)
0000:01:00.0 0300: 1002:4153
0000:01:00.1 0380: 1002:4173
0000:02:09.0 0200: 11ab:4320 (rev 13)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
In case on an installation using 'linux26' d-i can't load CD-ROM IDE module, so
I've have to install using expert26 mode. As Frans Pop reagrds me, "Load _only_ general IDE modules that are needed for CD access: cdrom,
ide-cd, isofs, generic." So I loaded only generic IDE module (the rest
are not loaded), so on this way d-i detect CD-ROM device and could
follow with the instalation process. On next steps it loads anothers
modules required by Serial ATA :)
Even testing uses 2.6.11 udebs, it let install 2.4 or 2.6.8 kernel versions (there is not 2.6.11 version)
Thanks and best regards,
Dooteo
Reply to: