Bug#319428: HPPA 'Sarge'
Package: installation
Version: 3.1r0
HP B-2600, factory stock ie: 500MHz A8600 proc., 512MB mem., empty 9.1
GB scsi hdd, ide cd-rom, initially USB keyboard/mouse changed to serial
console for printout of installation sequence.
Configured system to boot from cd-rom, failed to complete initial boot.
Used the logging mode of the terminal to save the boot sequence message.
As follows:
Firmware Version 1.4
Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-2000, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State Coprocessor State I/D
Cache --------- -------- --------------------- -----------------
------------- 0 500 MHz Active
Functional 512 kB/1 MB
Central Bus Speed: 120 MHz
Available memory: 536870912 bytes
Good memory required: 11649024 bytes
Primary boot path: FWSCSI.6.0
Alternate boot path: IDE
Console path: PCI4.0.0
Keyboard path: USB
Processor is booting from first available device.
To discontinue, press any key within 10 seconds.
Boot terminated.
----- Main Menu
-------------------------------------------------------------
Command Description
------- -----------
BOot [PRI|ALT|<path>] Boot from specified path
PAth [PRI|ALT|CON|KEY [<path>]] Display or modify a path
SEArch [DIsplay|[[IPL] [<path>]]] Search for boot devices
COnfiguration [<command>] Access Configuration
menu/commands
INformation [<command>] Access Information menu/commands
SERvice [<command>] Access Service menu/commands
DIsplay Redisplay the current menu
HElp [<menu>|<command>] Display help for menu or command
RESET Restart the system
-----
Main Menu: Enter command > BO ALT
Interact with IPL (Y, N, Q)?> Y
Booting... Boot IO Dependent Code (IODC) revision 0
HARD Booted. palo ipl 1.5 root@c3k Fri May 14 16:17:38 MDT 2004
Boot image contains:
0/vmlinux32 4319117 bytes @ 0x189e800
0/vmlinux64 5820539 bytes @ 0x1311000
0/ramdisk 6233937 bytes @ 0xd16000
Information: No console specified on kernel command line. This is
normal.
PALO will choose the console currently used by firmware (serial).Current
command line:
'0/vmlinux root=/dev/ram initrd=0/ramdisk init=/linuxrc' console=ttyS0
TERM=vt102
0: '0/vmlinux
1: root=/dev/ram
2: initrd=0/ramdisk
3: init=/linuxrc'
4: console=ttyS0
5: TERM=vt102
<#> edit the numbered field
'b' boot with this command line
'r' restore command line
'l' list dir
? 0
'0/vmlinux64
Current command line:
'0/vmlinux64 root=/dev/ram initrd=0/ramdisk init=/linuxrc' console=ttyS0
TERM=vt102
0: '0/vmlinux64
1: root=/dev/ram
2: initrd=0/ramdisk
3: init=/linuxrc'
4: console=ttyS0
5: TERM=vt102
<#> edit the numbered field
'b' boot with this command line
'r' restore command line
'l' list dir
? l
Directory listing of '0/.
ext2_init: bad magic 0x0
Failed to mount partition 0
Current command line:
'0/vmlinux64 root=/dev/ram initrd=0/ramdisk init=/linuxrc' console=ttyS0
TERM=vt102
0: '0/vmlinux64
1: root=/dev/ram
2: initrd=0/ramdisk
3: init=/linuxrc'
4: console=ttyS0
5: TERM=vt102
<#> edit the numbered field
'b' boot with this command line
'r' restore command line
'l' list dir
? b
Command line for kernel: 'root=/dev/ram init=/linuxrc' console=ttyS0
TERM=vt102 palo_kernel=0'0/vmlinux64'
Selected kernel: '0/vmlinux64 from partition 0
Selected ramdisk: /ramdisk from partition 0
ELF64 executable
Entry 00100000 first 00100000 n 3
Segment 0 load 00100000 size 3822080 mediaptr 0x1000
Segment 1 load 004a8000 size 318168 mediaptr 0x3a7000
Segment 2 load 004f8000 size 372869 mediaptr 0x3f5000
Loading ramdisk 6233937 bytes @ 1f9fd000...
Branching to kernel entry point 0x00100000. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
Linux version 2.6.8-2-64 (kyle@caradhras) (gcc version 3.3.5 (Debian
1:3.3.5-7)) #1 Tue Feb 8 05:54:00 EST 2005
FP[0] enabled: Rev 1 Model 16
The 64-bit Kernel has started...
Determining PDC firmware type: System Map.
model 00005de0 00000481 00000000 00000002 77b40b31 100000f0 00000008
000000b2 000000b2
vers 00000301
CPUID vers 17 rev 11 (0x0000022b)
capabilities 0x3
model 9000/785/B2600
Total Memory: 512 Mb
initrd: 2f9fd000-2ffeef51
initrd: reserving 1f9fd000-1ffeef51 (mem_max 20000000)
LCD display at fffffff0f05d0008,fffffff0f05d0000 registered
Built 1 zonelists
Kernel command line: root=/dev/ram init=/linuxrc' console=ttyS0
TERM=vt102 palo_kernel=0'0/vmlinux64
PID hash table entries: 16 (order 4: 256 bytes)
Console: colour dummy device 160x64
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 524288k available
Calibrating delay loop... 993.28 BogoMIPS
Security Scaffold v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like an
initrd
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. Astro BC Runway Port at 0xfffffffffed00000 [10] { 12, 0x0, 0x582,
0x0000b }
2. Elroy PCI Bridge at 0xfffffffffed30000 [10/0] { 13, 0x0, 0x782,
0x0000a }
3. Elroy PCI Bridge at 0xfffffffffed32000 [10/1] { 13, 0x0, 0x782,
0x0000a }
4. Piccolo W+ at 0xfffffffffffa0000 [32] { 0, 0x0, 0x5de, 0x00004 }
5. Memory at 0xfffffffffed10200 [49] { 1, 0x0, 0x0a4, 0x00009 }
CPU(s): 1 x PA8600 (PCX-W+) at 500.000000 MHz
SBA found Astro 2.1 at 0xfffffffffed00000
lba version TR4.0 (0x5) found at 0xfffffffffed30000
PCI: Enabled native mode for NS87415 (pif=0x8f)
lba version TR4.0 (0x5) found at 0xfffffffffed32000
iosapic: hpa not registered for 0000:01:03.0
SCSI subsystem initialized
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
STI GSC/PCI core graphics driver Version 0.9a
STI PCI graphic ROM found at fffffffff4800000 (2048 kB), fb at
fffffffffa000000 (32 MB)
id 35acda30-9a02587, conforms to spec rev. 8.0d
graphics card name: A1262A
stifb: 'A1262A' (id: 0x35acda30) not supported.
unwind_init: start = 0x103b66e0, end = 0x103d8790, entries = 8715
Performance monitoring counters enabled for Piccolo W+
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 128)
SuperIO: Serial port 1 at 0x3f8
SuperIO: Serial port 2 at 0x2f8
SuperIO: Parallel port at 0x378
SuperIO: Floppy controller at 0x3f0
SuperIO: ACPI at 0x7e0
SuperIO: USB regulator enabled
Soft power switch enabled, polling @ 0xfffffff0f0400804.
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 25 ports, IRQ sharing
enabled
ttyS0 at I/O 0x3f8 (irq = 195) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 196) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
sticon: Initializing STI text console.
Console: switching to colour STI console 128x48
mice: PS/2 mouse device common for all mice
HP SDC: No SDC found.
HP SDC MLC: Registering the System Domain Controller's HIL MLC.
HP SDC MLC: Request for raw HIL ISR hook denied
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
RAMDISK: Compressed image found at block 0
RAMDISK: incomplete write (-28 != 32768) 8388608
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 368k freed
attempt to access beyond end of device
ram0: rw=0, want=26816, limit=16384
attempt to access beyond end of device
ram0: rw=0, want=26816, limit=16384
Warning: unable to open an initial console.
attempt to access beyond end of device
ram0: rw=0, want=28528, limit=16384
EXT2-fs error (device ram0): ext2_get_inode: unable to read inode block
- inode=1813, block=14263
attempt to access beyond end of device
ram0: rw=0, want=28558, limit=16384
EXT2-fs error (device ram0): ext2_get_inode: unable to read inode block
- inode=1933, block=14278
Kernel panic: No init found. Try passing init= option to kernel.
end of log.
I downloaded a second iso & tried that cd but no change. The machine
will boot using the original HP-UX os/drive but needs a nis server to
get to the login prompt.
Reply to: