Bug#311427: installation-reports
Package: installation-reports
Debian-installer-version: RC3 installer (downloaded 5/13/05 from http://www.debian.org/devel/debian-installer/)
uname -a: Linux jasonslaptop 2.6.8-2-686 #1 Thu May 19 17:53:30 JST 2005 i686 GNU/Linux
Date: 5/15/05
Method: <How did you install? What did you boot off? If network
install, from where? Proxied?>
Netinstall CD
Machine: Dell Inspiron 8200, P4 1.6 Ghz, 640 MB PC2100 DDR, Geforce NV17 440 Go, Netgear WG511T (Atheros 5002 chipset)
Processor: P4 Mobile 1.6 Ghz
Memory: 640 MB PC2100 DDR
Root Device: <IDE? SCSI? IDE
Name of device?> 30 GB IDE Drive, make unkown
Root Size/partition table:
Filesystem Size Used Avail Use% Mounted on
/dev/hda8 5.5G 4.5G 653M 88% /
tmpfs 316M 0 316M 0% /dev/shm
/dev/hda1 15G 14G 1.1G 93% /mnt/windows
/dev/hda6 981M 875M 107M 90% /mnt/mandrake
/dev/hda3 1.8G 444M 1.3G 27% /home
none 10M 800K 9.3M 8% /dev
Output of lspci and lspci -n:
0000:00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge(rev 04)
0000:00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04)
0000:00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02)
0000:00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 42)
0000:00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02)
0000:00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02)
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio Controller (rev 02)
0000:00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem Controller (rev 02)
0000:01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 440 Go] (rev a3)
0000:02:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
0000:02:01.0 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
0000:02:01.1 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
0000:02:01.2 FireWire (IEEE 1394): Texas Instruments PCI4451 IEEE-1394 Controller
0000:07:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abgNIC (rev 01)
0000:00:00.0 0600: 8086:1a30 (rev 04)
0000:00:01.0 0604: 8086:1a31 (rev 04)
0000:00:1d.0 0c03: 8086:2482 (rev 02)
0000:00:1d.2 0c03: 8086:2487 (rev 02)
0000:00:1e.0 0604: 8086:2448 (rev 42)
0000:00:1f.0 0601: 8086:248c (rev 02)
0000:00:1f.1 0101: 8086:248a (rev 02)
0000:00:1f.5 0401: 8086:2485 (rev 02)
0000:00:1f.6 0703: 8086:2486 (rev 02)
0000:01:00.0 0300: 10de:0174 (rev a3)
0000:02:00.0 0200: 10b7:9200 (rev 78)
0000:02:01.0 0607: 104c:ac42
0000:02:01.1 0607: 104c:ac42
0000:02:01.2 0c00: 104c:8027
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O ]
Config network: [O ]
Detect CD: [O ]
Load installer modules: [O ]
Detect hard drives: [O ]
Partition hard drives: [O ]
Create file systems: [O ]
Mount partitions: [O ]
Install base system: [O ]
Install boot loader: [O ]
Reboot: [O ]
Comments/Problems: I initially setup the network connection and continued the installation process using the 3COM 3c905C 10/100 card.
I then compiled and installed the madwifi drivers and setup my WG511T with WPA-PSK using wpa_supplicant.
<Description of the install, in prose, and any thoughts, comments
and ideas you had during the initial install.>
The install went perfectly. The only problem I noticed was aesthetic. I had vertical red lines through the blue install screen.
Note: I used the linux26 install option.
Reply to: