Bug#231096:
Package: installation-reports
Debian-installer-version: Not sure about date, but it's the beta 2 installer from the Debian website
uname -a: Linux localhost 2.4.22-1-386 #9 Sat Oct 4 14:30:39 EST 2003 i686 GNU/Linux
Date: 14:30 (GMT-5) February 3, 2004
Method: Booted off the 100mb CD image for i386.
Rest of install was through FTP from the ftp://ftp.uwsg.indiana.edu/linux/debian/ mirror.
No proxy, other than the NAT. At least, not that I know of.
Machine: Dell Precision 650
Processor: dual 2.4Ghz Xeon
Memory: 1gb
Root Device: 04:0e.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07)
scsibus0:
0,0,0 0) 'SEAGATE ' 'ST373453LW ' 'DX10' Disk
Root Size/partition table:
Disk /dev/sda: 73.4 GB, 73407820800 bytes
255 heads, 63 sectors/track, 8924 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 5 40131 de Dell Utility
/dev/sda2 6 332 2626627+ b W95 FAT32
/dev/sda3 * 333 345 104422+ 83 Linux
/dev/sda4 346 8924 68910817+ f W95 Ext'd (LBA)
/dev/sda5 346 8670 66870531 83 Linux
/dev/sda6 8671 8924 2040223+ 82 Linux swap
/dev/sda3 = /boot
/dev/sda5 = /
/dev/sda6 = swap
other partitions ignored
Output of lspci:
00:00.0 Host bridge: Intel Corp. E7505 Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corp. E7000 Series Processor to AGP Controller (rev 03)
00:02.0 PCI bridge: Intel Corp. E7000 Series Hub Interface B PCI-to-PCI Bridge (rev 03)
00:1d.0 USB Controller: Intel Corp. 82801DB USB (Hub #1) (rev 01)
00:1d.1 USB Controller: Intel Corp. 82801DB USB (Hub #2) (rev 01)
00:1d.2 USB Controller: Intel Corp. 82801DB USB (Hub #3) (rev 01)
00:1d.7 USB Controller: Intel Corp. 82801DB USB2 (rev 01)
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corp. 82801DB LPC Interface Controller (rev 01)
00:1f.1 IDE interface: Intel Corp. 82801DB Ultra ATA Storage Controller (rev 01)00:1f.3 SMBus: Intel Corp. 82801DB/DBM SMBus Controller (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation NV18GL [Quadro4 NVS AGP 8x] (rev a2)
02:1c.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04)
02:1d.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
02:1e.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04)
02:1f.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
03:0e.0 Ethernet controller: Intel Corp. 82545EM Gigabit Ethernet Controller (Copper) (rev 01)
04:0e.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07)
05:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
05:0e.0 Ethernet controller: Linksys Network Everywhere Fast Ethernet 10/100 model NC100 (rev 11)
Base System Installation Checklist:
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [ ]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Comments/Problems:
The step of configuring my /etc/apt/sources.list never believed it had
completed successfully. Once I edited it by hand, I discovered that it
was inserting a new set of correct lines each time I attempted to
configure it from the GUI, but even hand editing didn't convince the
system that it had completed the step. Once I just skipped ahead to
installing things, it went fine.
Reply to: