Bug#286070: installation-reports
Package: installation-reports
Debian-installer-version:
uname -a: Linux priesemut 2.6.8-1-386 #1 Thu Nov 11 12:18:43 EST 2004
i686 GNU/Linux
Date: 12-14-2004 18:00-20:00
Method: Installing from NetInst CD Image, booting from NetInst CD, other
packages loading over http-proxy from mirror
sunsite.informatik.rwth-aachen.de
Machine: Fujitsu-Siemens Scenix Edition X100
Processor: Intel Celeron 2.8 GHz
Memory: 512 MB
Root Device: 3ware Escalade 8006-2LP RAID-Controller,
using to Maxtore 80 GB HD formated as RAID 1
I installed kernel 2.6.8 because of it's build-in
device driver
for 3ware RAID controller. Since kernel release 2.6.7-3 the
kernel includes the latest available device driver (version
1.26.00.39) offered by the manufacturer of this controller.
Evaluated by 'cat /proc/scsi/3w-xxxx/O' .
Root Size/partition table: /dev/sda1 type 83 (Linux) mounted as root
(/), formated with xfs, size 4 GB,
primary partition, bootable, lilo
in MBR
/dev/sda2 type 82 (swap), size 512 MB,
primary partition
free space to be formated and assinged
later ...
Output of lspci:
0000:00:00.0 Host bridge: Intel Corp. 82845G/GL[Brookdale-G]/GE/PE DRAM
Controller/Host-Hub Interface (rev 01)
0000:00:02.0 VGA compatible controller: Intel Corp.
82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device (rev 01)
0000:00:1d.0 USB Controller: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
0000:00:1d.1 USB Controller: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)
0000:00:1d.2 USB Controller: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)
0000:00:1d.7 USB Controller: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB
2.0 EHCI Controller (rev 01)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 81)
0000:00:1f.0 ISA bridge: Intel Corp. 82801DB/DBL (ICH4/ICH4-L) LPC
Bridge (rev 01)
0000:00:1f.1 IDE interface: Intel Corp. 82801DB/DBL (ICH4/ICH4-L)
UltraATA-100 IDE Controller (rev 01)
0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
SMBus Controller (rev 01)
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
0000:02:01.0 Ethernet controller: Linksys NC100 Network Everywhere Fast
Ethernet 10/100 (rev 11)
0000:02:05.0 RAID bus controller: 3ware Inc 3ware 7000-series ATA-RAID
(rev 01)
0000:02:09.0 Network controller: AVM Audiovisuelles MKTG & Computer
System GmbH Fritz!PCI v2.0 ISDN (rev 02)
Output of lspci -n:
0000:00:00.0 0600: 8086:2560 (rev 01)
0000:00:02.0 0300: 8086:2562 (rev 01)
0000:00:1d.0 0c03: 8086:24c2 (rev 01)
0000:00:1d.1 0c03: 8086:24c4 (rev 01)
0000:00:1d.2 0c03: 8086:24c7 (rev 01)
0000:00:1d.7 0c03: 8086:24cd (rev 01)
0000:00:1e.0 0604: 8086:244e (rev 81)
0000:00:1f.0 0601: 8086:24c0 (rev 01)
0000:00:1f.1 0101: 8086:24cb (rev 01)
0000:00:1f.3 0c05: 8086:24c3 (rev 01)
0000:00:1f.5 0401: 8086:24c5 (rev 01)
0000:02:01.0 0200: 1317:0985 (rev 11)
0000:02:05.0 0104: 13c1:1001 (rev 01)
0000:02:09.0 0280: 1244:0e00 (rev 02)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
hda: HL-DT-ST DVDRAM GSA-4160B, ATAPI CD/DVD-ROM drive
hdc: HL-DT-STDVD-ROM GDR8163B, ATAPI CD/DVD-ROM drive
Load installer modules: [O]
Detect hard drives: [O]
3ware Storage Controller device driver for Linux v1.26.00.039.
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 17 (level, low) -> IRQ 201
scsi0 : Found a 3ware Storage Controller at 0x3400, IRQ: 201,
P-chip: 1.3
scsi0 : 3ware Storage Controller
Using anticipatory io scheduler
Vendor: 3ware Model: Logical Disk 0 Rev: 1.2
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 160084480 512-byte hdwr sectors (81963 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Partition hard drives: [O]
Create file systems: [O] xfs
Mount partitions: [O]
Install base system: [O]
Install boot loader: [E/O see comments below]
Reboot: [O ]
Comments/Problems:
As mentioned in the installation manual, installing bootload GRUB in the MBR
of xfs filesystem canceled when the loadbar reaches 50%. Second try wiht
LILO
works fine.
Please, feel free to ask some more detailed questions if required or
usefull.
Thanks to the whole team for building and delivering the new debian (sarge)
installer! Very well done!
By for now and greetinx from Upper Bavaria
Guido Haase <guido@haase-it.de>
_____________________________________
Haase IT - Security by experience
Address Haase IT
Oberbuchen 2
D-83670 Bad Heilbrunn
Phone +49-(0) 80 46-18 87 66
Fax +49-(0) 80 46-18 87 67
Mobil +49-(0) 160-8 44 35 53
E-Mail info@haase-it.de
Internet http://www.haase-it.de
IT-Security · Linux · Networks
_____________________________________
Reply to: