Package: installation-reports
INSTALL REPORT
Debian-installer-version: 16 Dec 2004 http://cdimage.debian.org/pub/cdimage-testing/sarge_d-i/i386/rc2/sarge-i386-netinst.iso
uname -a: Linux mp-samdb-1 2.4.27-1-386 #1 Fri Sep 3 06:24:46 UTC 2004 i686 GNU/Linux
Date: 16 Dec 2004 15:20
Method: Via Network, proxied
Machine: Fujitsu Siemens RX 100
Processor: Intel Celeron 2,6 Ghz
Memory: 884
Root Device: IDE-Raid /dev/ataraid/d0
Root Size/partition table:
Disk /dev/ataraid/d0: 80.0 GB, 80000000000 bytes
255 heads, 63 sectors/track, 9726 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/ataraid/d0p1 * 1 9388 75409078+ 83 Linux
/dev/ataraid/d0p2 9389 9726 2714985 82 Linux swap
Output of lspci and lspci -n:
lspci:
0000:00:00.0 Host bridge: ServerWorks GCNB-LE Host Bridge (rev 32)
0000:00:00.1 Host bridge: ServerWorks GCNB-LE Host Bridge
0000:00:04.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
0000:00:08.0 Ethernet controller: Intel Corp. 82540EM Gigabit Ethernet Controller (rev 02)
0000:00:0a.0 RAID bus controller: Promise Technology, Inc. PDC20270 (FastTrak100 LP/TX2/TX4) (rev 02)
0000:00:0c.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 0d)
0000:00:0f.0 ISA bridge: ServerWorks CSB6 South Bridge (rev a0)
0000:00:0f.1 IDE interface: ServerWorks CSB6 RAID/IDE Controller (rev a0)
0000:00:0f.2 USB Controller: ServerWorks CSB6 OHCI USB Controller (rev 05)
0000:00:0f.3 Host bridge: ServerWorks GCLE-2 Host Bridge
lspci -n
0000:00:00.0 0600: 1166:0017 (rev 32)
0000:00:00.1 0600: 1166:0017
0000:00:04.0 0300: 1002:4752 (rev 27)
0000:00:08.0 0200: 8086:100e (rev 02)
0000:00:0a.0 0104: 105a:6268 (rev 02)
0000:00:0c.0 0200: 8086:1229 (rev 0d)
0000:00:0f.0 0601: 1166:0203 (rev a0)
0000:00:0f.1 0101: 1166:0213 (rev a0)
0000:00:0f.2 0c03: 1166:0221 (rev 05)
0000:00:0f.3 0600: 1166:0227
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [E] [O]
Mount partitions: [ ] [O]
Install base system: [ ] [O]
Install boot loader: [ ] [O]
Reboot: [ ] [E]
Comments/Problems:
1st Installation:
Swap has been put into a extended partition, causing errors while creating the swapspace - manually editing the partition-table to only use primary partitions solved that problem on the second run.
The second installer run left the system not bootable, because of the lack of the bootloader in /dev/ataraid/d0 - after chrooting into the installed system and manually running "grub-install /dev/ataraid/d0" the system came up.