Package: installation-reports
INSTALL REPORT
Debian-installer-version: RC2 i386 netinst
uname -a: Linux yuchenko 2.6.8-1-686 #1 Thu Nov 25 04:34:30 UTC 2004 i686 GNU/Linux
Date: 2004-12-10&11
Method: boot from CD, packages by http, not proxied
Machine: ASUS AP140R-E1
Processor: Intel P IV
Memory: 2 Gibabyte
Root Device: /dev/sda1
Root Size/partition table:
Disk /dev/sda: 203.9 GB, 203928109056 bytes
255 heads, 63 sectors/track, 24792 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 34 273073+ 83 Linux
/dev/sda2 35 2804 22250025 5 Extended
/dev/sda3 2805 24792 176618610 83 Linux
/dev/sda5 35 642 4883728+ 83 Linux
/dev/sda6 643 1007 2931831 83 Linux
/dev/sda7 1008 1337 2650693+ 82 Linux swap
/dev/sda8 1338 1345 64228+ 83 Linux
/dev/sda9 1346 2804 11719386 83 Linux
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sda1 255912 109527 132732 46% /
extended
/dev/sda3 173846400 32860 164982612 1% /data
/dev/sda5 4807056 139708 4423164 4% /usr
/dev/sda6 2885780 97068 2642124 4% /var
swap
/dev/sda8 60185 4128 52846 8% /tmp
/dev/sda9 11535344 32880 10916496 1% /home
tmpfs 1038428 8 1038420 1% /dev/shm
Output of lspci and lspci -n piped through sort:
0000:00:00.0 0600: 8086:2578 (rev 02)
0000:00:00.0 Host bridge: Intel Corp. 82875P Memory Controller Hub (rev 02)
0000:00:03.0 0604: 8086:257b (rev 02)
0000:00:03.0 PCI bridge: Intel Corp. 82875P Processor to PCI to CSA Bridge (rev 02)
0000:00:1c.0 0604: 8086:25ae (rev 02)
0000:00:1c.0 PCI bridge: Intel Corp. 6300ESB 64-bit PCI-X Bridge (rev 02)
0000:00:1d.0 0c03: 8086:25a9 (rev 02)
0000:00:1d.0 USB Controller: Intel Corp. 6300ESB USB Universal Host Controller (rev 02)
0000:00:1d.1 0c03: 8086:25aa (rev 02)
0000:00:1d.1 USB Controller: Intel Corp. 6300ESB USB Universal Host Controller (rev 02)
0000:00:1d.4 0880: 8086:25ab (rev 02)
0000:00:1d.4 System peripheral: Intel Corp. 6300ESB Watchdog Timer (rev 02)
0000:00:1d.5 0800: 8086:25ac (rev 02)
0000:00:1d.5 PIC: Intel Corp. 6300ESB I/O Advanced Programmable Interrupt Controller (rev 02)
0000:00:1d.7 0c03: 8086:25ad (rev 02)
0000:00:1d.7 USB Controller: Intel Corp. 6300ESB USB2 Enhanced Host Controller (rev 02)
0000:00:1e.0 0604: 8086:244e (rev 0a)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 0a)
0000:00:1f.0 0601: 8086:25a1 (rev 02)
0000:00:1f.0 ISA bridge: Intel Corp. 6300ESB LPC Interface Controller (rev 02)
0000:00:1f.1 0101: 8086:25a2 (rev 02)
0000:00:1f.1 IDE interface: Intel Corp. 6300ESB PATA Storage Controller (rev 02)
0000:00:1f.2 0104: 8086:25b0 (rev 02)
0000:00:1f.2 RAID bus controller: Intel Corp. 6300ESB SATA RAID Controller (rev 02)
0000:00:1f.3 0c05: 8086:25a4 (rev 02)
0000:00:1f.3 SMBus: Intel Corp. 6300ESB SMBus Controller (rev 02)
0000:01:01.0 0200: 8086:1075
0000:01:01.0 Ethernet controller: Intel Corp. 82547GI Gigabit Ethernet Controller
0000:03:03.0 0300: 1002:4752 (rev 27)
0000:03:03.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
0000:03:05.0 0200: 8086:1076
0000:03:05.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
A 386 kernel was installed, but the system is a Pentium 4,
so a 686 kernel is expected ....
The 386 kernel only addresses 1 gigabyte of RAM,
the 686 supports the 2 Gb installed in the machine.
(this install report is about a two gigabyte computer)
<backgroundinformation about="kernel configuration">
<config for="386" partitial="yes">
#
# Firmware Drivers
#
CONFIG_EDD=m
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
CONFIG_MATH_EMULATION=y
</config>
<config for="686" partitial="yes">
# Firmware Drivers
#
CONFIG_EDD=m
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_HIGHMEM=y
# CONFIG_HIGHPTE is not set
# CONFIG_MATH_EMULATION is not set
</config>
<backgroundinformation>
This output of `cat /proc/cpuinfo` during install:
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 3
model name : Intel(R) Pentium(R) 4 CPU 3.00GHz
stepping : 4
cpu MHz : 2993.469
cache size : 1024 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pni monitor ds_cpl cid
bogomips : 5931.00
If CPU dections is done on other information, then let me known.
The 686 kernel has some other "quirks" on this hardware,
but that will be in another bugreport.
Cheers
Geert Stappers
Attachment:
signature.asc
Description: Digital signature