Bug#275539: install with debian installer
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Package: installation-reports
Debian-installer-version:
<http://cdimage.debian.org/pub/cdimage-testing/sid_d-i/i386/pre-rc2/sarge-i386-netinst.iso>
uname -a: <Linux debian 2.6.8-1-386 #1 Mon Sep 13 23:29:55 EDT 2004 i686
GNU/Linux>
Date: <2004-10-08 17:30 UTC>
Method: <Wie haben Sie installiert? Von was haben Sie gebootet? Falls es
~ eine Netzwerkinstallation war, von wo? Wurde ein Proxy verwendet?>
Machine: <Compaq DeskPro>
Processor: Pentium II / 400
Memory: 448 MB
Root Device: <IDE Western Digital WDC AC26400R ATA>
Disk /dev/hda: 13328 cylinders, 15 heads, 63 sectors/track
Units = cylinders of 483840 bytes, blocks of 1024 bytes, counting from 0
~ Device Boot Start End #cyls #blocks Id System
/dev/hda1 * 0+ 12702 12703- 6002136 83 Linux
/dev/hda2 12703 13327 625 295312+ f W95 Ext'd (LBA)
/dev/hda3 0 - 0 0 0 Empty
/dev/hda4 0 - 0 0 0 Empty
/dev/hda5 12703+ 13327 625- 295281 82 Linux swap
0000:00:00.0 0600: 8086:7190 (rev 02)
0000:00:01.0 0604: 8086:7191 (rev 02)
0000:00:0d.0 0200: 8086:1229 (rev 05)
0000:00:14.0 0601: 8086:7110 (rev 02)
0000:00:14.1 0101: 8086:7111 (rev 01)
0000:00:14.2 0c03: 8086:7112 (rev 01)
0000:00:14.3 0680: 8086:7113 (rev 02)
0000:01:00.0 0300: 1002:4742 (rev 5c)
0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge (rev 02)
0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP
bridge (rev 02)
0000:00:0d.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro
100] (rev 05)
0000:00:14.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
0000:00:14.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
0000:00:14.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
0000:00:14.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro
AGP 1X/2X (rev 5c)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [o ]
Configure network HW: [o ]
Config network: [o ]
Detect CD: [o ]
Load installer modules: [o ]
Detect hard drives: [o ]
Partition hard drives: [o ]
Create file systems: [o ]
Mount partitions: [o ]
Install base system: [o ]
Install boot loader: [o ]
Reboot: [o ]
Comments/Problems:
hda: task_out_intr: status:0x51 { DriveReady SeekComplete Error }
hda: task_out_intr: status:0x04 { DriveStatusError }
<Beschreibung der Installation, ausführlich, inklusive aller Gedanken,
Kommentare
~ und Ideen, die Sie während der anfänglichen Installation hatten.>
I'm an experienced Linux user for several years, but new to debian. I'm
unable to install additional software (after making an mistake during
baseinstall ?). Neither aptitude nor base-config shows any packages to
me instead the update packages. apt-get install works, if I know the
right package name (lshw or mc). Please give me at least an ncurses
interface to install additional software!
Linux version 2.6.8-1-386 (dilinger@toaster.hq.voxel.net) (gcc version
3.3.4 (Debian 1:3.3.4-11)) #1 Mon Sep 13 23:29:55 EDT 2004
BIOS-provided physical RAM map:
~ BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
~ BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
~ BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
~ BIOS-e820: 0000000000100000 - 000000001c000000 (usable)
~ BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
448MB LOWMEM available.
On node 0 totalpages: 114688
~ DMA zone: 4096 pages, LIFO batch:1
~ Normal zone: 110592 pages, LIFO batch:16
~ HighMem zone: 0 pages, LIFO batch:1
DMI 2.1 present.
ACPI disabled because your bios is from 98 and too old
You can enable it with acpi=force
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=Linux ro root=301
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 398.377 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 447144k/458752k available (1329k kernel code, 10844k reserved,
727k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 784.38 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0183fbff 00000000 00000000 00000040
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: IRQ9 SCI: Edge set to Level Trigger.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 398.0188 MHz.
..... host bus clock speed is 99.0546 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an
initrd
Freeing initrd memory: 4316k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xed880, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fef70
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x604e, dseg 0xf0000
pnp: 00:12: ioport range 0x15c-0x15d has been reserved
pnp: 00:12: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:13: ioport range 0xf800-0xf81f has been reserved
pnp: 00:13: ioport range 0xf820-0xf83f has been reserved
pnp: 00:13: ioport range 0xfc00-0xfc0f has been reserved
PnPBIOS: 18 nodes reported by PnP BIOS; 18 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Address space collision on region 7 of bridge 0000:00:14.3 [f800:f83f]
PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:14.0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4316 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:14.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
~ ide0: BM-DMA at 0x2040-0x2047, BIOS settings: hda:DMA, hdb:pio
~ ide1: BM-DMA at 0x2048-0x204f, BIOS settings: hdc:pio, hdd:pio
hda: WDC AC26400R, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 12594960 sectors (6448 MB) w/512KiB Cache, CHS=13328/15/63, UDMA(33)
~ /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
hdc: Compaq CRD-8322B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
SGI XFS with ACLs, security attributes, realtime, large block numbers,
no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem hda1
Ending clean XFS mount for filesystem: hda1
XFS mounting filesystem hda1
Ending clean XFS mount for filesystem: hda1
Adding 295272k swap on /dev/hda5. Priority:-1 extents:1
Real Time Clock Driver v1.12
hdc: ATAPI 32X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
Capability LSM initialized
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
Linux agpgart interface v0.100 (c) Dave Jones
e100: Intel(R) PRO/100 Network Driver, 3.0.18
e100: Copyright(c) 1999-2004 Intel Corporation
PCI: Found IRQ 11 for device 0000:00:0d.0
e100: eth0: e100_probe: addr 0x40200000, irq 11, MAC addr 00:08:C7:79:FE:52
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
inserting floppy driver for 2.6.8-1-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
input: PC Speaker
input: PS/2 Generic Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
agpgart: Detected an Intel 440BX Chipset.
agpgart: Maximum main memory to use for agp memory: 381M
agpgart: AGP aperture is 64M @ 0x44000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
~ ACPI-1133: *** Error: Method execution failed [\_SB_.LNKA._STA]
(Node dbffe480), AE_NOT_EXIST
~ ACPI-0154: *** Error: Method execution failed [\_SB_.LNKA._STA]
(Node dbffe480), AE_NOT_EXIST
~ ACPI-1133: *** Error: Method execution failed [\_SB_.LNKB._STA]
(Node dbffeee0), AE_NOT_EXIST
~ ACPI-0154: *** Error: Method execution failed [\_SB_.LNKB._STA]
(Node dbffeee0), AE_NOT_EXIST
~ ACPI-1133: *** Error: Method execution failed [\_SB_.LNKC._STA]
(Node dbffedc0), AE_NOT_EXIST
~ ACPI-0154: *** Error: Method execution failed [\_SB_.LNKC._STA]
(Node dbffedc0), AE_NOT_EXIST
~ ACPI-1133: *** Error: Method execution failed [\_SB_.LNKD._STA]
(Node dbffeca0), AE_NOT_EXIST
~ ACPI-0154: *** Error: Method execution failed [\_SB_.LNKD._STA]
(Node dbffeca0), AE_NOT_EXIST
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
~ ACPI-1133: *** Error: Method execution failed [\_SB_.LNKA._STA]
(Node dbffe480), AE_NOT_EXIST
~ ACPI-0154: *** Error: Method execution failed [\_SB_.LNKA._STA]
(Node dbffe480), AE_NOT_EXIST
~ ACPI-1133: *** Error: Method execution failed [\_SB_.LNKB._STA]
(Node dbffeee0), AE_NOT_EXIST
~ ACPI-0154: *** Error: Method execution failed [\_SB_.LNKB._STA]
(Node dbffeee0), AE_NOT_EXIST
~ ACPI-1133: *** Error: Method execution failed [\_SB_.LNKC._STA]
(Node dbffedc0), AE_NOT_EXIST
~ ACPI-0154: *** Error: Method execution failed [\_SB_.LNKC._STA]
(Node dbffedc0), AE_NOT_EXIST
~ ACPI-1133: *** Error: Method execution failed [\_SB_.LNKD._STA]
(Node dbffeca0), AE_NOT_EXIST
~ ACPI-0154: *** Error: Method execution failed [\_SB_.LNKD._STA]
(Node dbffeca0), AE_NOT_EXIST
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
<saw@saw.sw.com.sg> and others
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
PCI: Found IRQ 11 for device 0000:00:14.2
uhci_hcd 0000:00:14.2: Intel Corp. 82371AB/EB/MB PIIX4 USB
uhci_hcd 0000:00:14.2: irq 11, io base 00002020
uhci_hcd 0000:00:14.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 17
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x04 { DriveStatusError }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x04 { DriveStatusError }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x04 { DriveStatusError }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x04 { DriveStatusError }
hda: DMA disabled
ide0: reset: success
hda: task_out_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_out_intr: error=0x04 { DriveStatusError }
hda: task_out_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_out_intr: error=0x04 { DriveStatusError }
hda: task_out_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_out_intr: error=0x04 { DriveStatusError }
hda: task_out_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_out_intr: error=0x04 { DriveStatusError }
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02c95a0(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04Aborted Command
SCSI subsystem initialized
st: Version 20040403, fixed bufsize 32768, s/g segs 256
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.4 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
iD8DBQFBZt6xueLApKuCk+gRAg4TAKCQclhgOol24yukpVOiHX+EGMXlSwCgyjmU
qNKW9EcxvxzfV6vQT5aX2lM=
=Peoi
-----END PGP SIGNATURE-----
Reply to: