Bug#275405: Debian-Installer installation report
Package: installation-reports
Debian-installer-version: d-i pre-rc2
uname -a: Linux meriadoc 2.4.27-1-k7 #1 Fri Sep 3 06:21:29 UTC 2004 i686
GNU/Linux
(after installing kernel-image-2.4.27-k7 rather than -i386)
Date: 7th October 2004
Method: Booted from sarge-i386-netinst CD downloaded from debian.org.
Installed as "expert".
Machine: Homebuilt PC
Processor: 1GB AMD Athlon
Memory: 384MB
Root Device: Pair of IDE HDDs, set as RAID1. / is /dev/md2
Root Size/partition table:
/dev/md0 /boot 30MB
/dev/md1 swap 512MB
/dev/md2 / 10GB
/dev/md3 /home 10GB
/dev/md4 /data (whatever's left of 120GB)
Output of lspci and lspci -n:
alan@meriadoc:~$ lspci
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365
[KT133/KM133] (rev 02)
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133
AGP]
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
South] (rev 22)
0000:00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10)
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 10)
0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 10)
0000:00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
ACPI] (rev 30)
0000:00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro
AGP 1X/2X (rev 5c)
alan@meriadoc:~$ lspci -n
0000:00:00.0 0600: 1106:0305 (rev 02)
0000:00:01.0 0604: 1106:8305
0000:00:07.0 0601: 1106:0686 (rev 22)
0000:00:07.1 0101: 1106:0571 (rev 10)
0000:00:07.2 0c03: 1106:3038 (rev 10)
0000:00:07.3 0c03: 1106:3038 (rev 10)
0000:00:07.4 0600: 1106:3057 (rev 30)
0000:00:09.0 0200: 10ec:8139 (rev 10)
0000:01:00.0 0300: 1002:4742 (rev 5c)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [o]
Configure network HW: [o]
Config network: [o]
Detect CD: [o]
Load installer modules: [o]
Detect hard drives: [o]
Partition hard drives: [o]
Create file systems: [o]
Mount partitions: [o]
Install base system: [o]
Install boot loader: [o]
Reboot: [o]
Comments/Problems:
Finally managed to get the system booting off of a software RAID
mirror... Easy, and painless, although I used grub rather than lilo
which I would have preferred.
Reply to: