Bug#275315:
Package: installation-reports
Debian-installer-version: 07 Oct 2004 -
http://cdimage.debian.org/pub/cdimage-testing/sid_d-i/i386/pre-rc2/sarge
-i386-netinst.iso
uname -a: Linux aap 2.6.8-1-686
Date: 07 Oct 2004 - 11am~12am CET
Method: boot of cd with netinst base, using authentication through squid
proxy
Machine: Dell PowerEdge 2550
Processor: Dual Pentium 3 1000Mhz Coppermine
Memory: 3Gb
Root Device: Scsi, PERC 3/Di Raid controller
Root Size/partition table:
/dev/sda1 * 1 122 979933+ 83 Linux
<-- root
/dev/sda2 123 4425 34563847+ 5 Extended
/dev/sda5 123 244 979933+ 83 Linux
/dev/sda6 245 609 2931831 83 Linux
/dev/sda7 610 4317 29784478+ 83 Linux
/dev/sda8 4318 4425 867478+ 82 Linux
swap
Output of lspci and lspci -n:
0000:00:00.0 Host bridge: ServerWorks CNB20HE Host Bridge (rev
23)
0000:00:00.1 Host bridge: ServerWorks CNB20HE Host Bridge (rev
01)
0000:00:00.2 Host bridge: ServerWorks CNB20HE Host Bridge (rev
01)
0000:00:00.3 Host bridge: ServerWorks CNB20HE Host Bridge (rev
01)
0000:00:0e.0 VGA compatible controller: ATI Technologies Inc
Rage XL (rev 27)
0000:00:0f.0 ISA bridge: ServerWorks OSB4 South Bridge (rev 50)
0000:00:0f.1 IDE interface: ServerWorks OSB4 IDE Controller
0000:00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB
Controller (rev 04)
0000:01:08.0 Ethernet controller: Broadcom Corporation NetXtreme
BCM5700 Gigabit Ethernet (rev 12)
0000:02:02.0 PCI bridge: Intel Corp. 80960RM [i960RM Bridge]
(rev 01)
0000:02:02.1 RAID bus controller: Dell PowerEdge Expandable RAID
Controller 3/Di (rev 01)
0000:02:04.0 Ethernet controller: Intel Corp. 82557/8/9
[Ethernet Pro 100] (rev 08)
0000:00:00.0 0600: 1166:0008 (rev 23)
0000:00:00.1 0600: 1166:0008 (rev 01)
0000:00:00.2 0600: 1166:0006 (rev 01)
0000:00:00.3 0600: 1166:0006 (rev 01)
0000:00:0e.0 0300: 1002:4752 (rev 27)
0000:00:0f.0 0601: 1166:0200 (rev 50)
0000:00:0f.1 0101: 1166:0211
0000:00:0f.2 0c03: 1166:0220 (rev 04)
0000:01:08.0 0200: 14e4:1644 (rev 12)
0000:02:02.0 0604: 8086:0962 (rev 01)
0000:02:02.1 0104: 1028:0002 (rev 01)
0000:02:04.0 0200: 8086:1229 (rev 08)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [E]
Reboot: [O]
Comments/Problems:
Grub failed to install. VC/3 reports that it's probing devices and then
reported "file /boot/grub/stage1 not read correctly." Lilo installed
fine
Reply to: