Bug#274314: install report
Package: installation-reports
INSTALL REPORT
Debian-installer-version: <Set-27-2004. Address:
http://cdimage.debian.org/pub/cdimage-testing/sid_d-i/i386/current/sarge-i386-netinst.iso>
uname -a: <Linux frank 2.6.8-1-386 #1 Mon Sep 13 23:56:00 EDT 2004 i686
GNU/Linux>
Date: <Set-29-2004. Around 6:00PM>
Method:
How did you install?
Booted sarge install cd.
What did you boot off?
The cd, address above.
If network install, from where? Proxied?
No network install, no proxy.
Machine: <Assembled from parts>
Processor: Athlon XP 1600
Memory: 256MB DDR
Motherboard: Abit KG-7
2 Ethernet cards: Encore (8139c chip, see lspci...).
LG DVD DRD-8160B
Matshita CDRW CW-7585
40GB Harddisk Samsung SP0411N 7200rpm
80 Seagate Barracuda ST380021A 7200rpm
Root Device: </dev/hda IDE>
Root Size/partition table: Feel free to paste the full partition
table, with notes on which partitions are mounted where.
Output of fdisk -l on both disks:
Disk /dev/hda: 40.0 GB, 40060403712 bytes
255 heads, 63 sectors/track, 4870 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 1 631 5068476 83 Linux
/dev/hda2 * 632 2201 12611025 83 Linux #(/ of
installed suse 9.1)
/dev/hda4 2202 4870 21438742+ f W95 Ext'd (LBA)
/dev/hda5 2202 3500 10434186 83 Linux
/dev/hda6 3501 4870 11004493+ 83 Linux
Disk /dev/hdb: 80.0 GB, 80026361856 bytes
255 heads, 63 sectors/track, 9729 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hdb1 1 61 489951 82 Linux swap
/dev/hdb2 62 4001 31648050 83 Linux
/dev/hdb3 4002 6001 16065000 83 Linux
/dev/hdb4 6002 9728 29937127+ f W95 Ext'd (LBA)
/dev/hdb5 6002 8500 20073186 83 Linux
/dev/hdb6 8501 9728 9863878+ 83 Linux
Output of lspci and lspci -n:
lspci:
0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 [IGD4-1P]
System Controller (rev 13)
0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 [IGD4-1P]
AGP Bridge
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
South] (rev 40)
0000:00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
(rev 40)
0000:00:09.0 Multimedia video controller: Brooktree Corporation Bt878
Video Capture (rev 11)
0000:00:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio
Capture (rev 11)
0000:00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
0000:00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
0000:00:0f.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1
(rev 0a)
0000:00:0f.1 Input device controller: Creative Labs SB Live! MIDI/Game
Port (rev 0a)
0000:01:05.0 VGA compatible controller: nVidia Corporation NV11
[GeForce2 MX/MX 400] (rev b2)
lspci -n:
0000:00:00.0 0600: 1022:700e (rev 13)
0000:00:01.0 0604: 1022:700f
0000:00:07.0 0601: 1106:0686 (rev 40)
0000:00:07.1 0101: 1106:0571 (rev 06)
0000:00:07.4 0c05: 1106:3057 (rev 40)
0000:00:09.0 0400: 109e:036e (rev 11)
0000:00:09.1 0480: 109e:0878 (rev 11)
0000:00:0b.0 0200: 10ec:8139 (rev 10)
0000:00:0d.0 0200: 10ec:8139 (rev 10)
0000:00:0f.0 0401: 1102:0002 (rev 0a)
0000:00:0f.1 0980: 1102:7002 (rev 0a)
0000:01:05.0 0300: 10de:0110 (rev b2)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [0]
Configure network HW: [0]
Config network: [E]
Detect CD: [0]
Load installer modules: [0]
Detect hard drives: [0]
Partition hard drives: [ ]
Create file systems: [0]
Mount partitions: [0]
Install base system: [0]
Install boot loader: [0]
Reboot: [0]
Comments/Problems:
<Description of the install, in prose, and any thoughts, comments
and ideas you had during the initial install.>
Quite nice install process. I was surprised, since my last trial
with a netinst cd and a
business card cd, which didn't succeeded in the same machine (install
process hanged).
For this time I chose expert26. Partitioning: full control. The machine
has a working suse 9.1 also,
and I needed to install Lilo in /dev/hdb6 (choosen location for Sarge),
as to not mess with suse's
grub in /dev/hda1.
The partition tool was used only to choose / as /dev/hdb6 and swap. I
didn't partition anything
beyond that. Formatted / with raiser.
Everything works great. I didn't edit grub's menu.lst, to load Debian,
as I use smart boot manager
(from floppy) to load both.
- The config network error above is about my second eth card. Its not
exactly an error. The machine
nat's internet for another win machine and this setup wasn't done/asked.
No problem doing it by hand,
but why not include it in the setup?
- The tv/radio card has a few issues: The way d-i installed it, I can't
switch channels (no tuner module
loaded, I guess...). Perhaps you might want to include steps for
choosing which tv card is in the machine
(cardlist), which tuner and whether it has radio or not. In my previous
Debian install, I modprobed
the card with:
modprobe bttv card=37 radio=1
modprobe tuner type=2
These are the relevant dmesg lines (Please notice the kernel has been
upgraded to 2.6.8-1-k7, no more *-i386):
frank:/home/bruno# dmesg |grep bttv
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 5, latency: 32, mmio: 0xde001000
bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffc0ff [init]
bttv: readee error
bttv0: using tuner=-1
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: registered device video0
bttv0: registered device vbi0
Temp/fan sensors:
d-i didn't install/load modules for my sensors by default, it seems. If
I do:
sensors
I get a
No sensors found!
Then, I do:
modprobe i2c-isa
modprobe via686a
I get:
Adapter: ISA adapter
CPU core: +1.81 V (min = +0.06 V, max = +3.10 V)
+2.5V: +2.69 V (min = +0.06 V, max = +3.10 V)
I/O: +3.53 V (min = +3.12 V, max = +3.45 V) ALARM
+5V: +4.93 V (min = +4.73 V, max = +5.20 V)
+12V: +12.48 V (min = +11.35 V, max = +12.48 V)
CPU Fan: 5720 RPM (min = 3000 RPM, div = 2)
P/S Fan: 0 RPM (min = 3000 RPM, div = 2) ALARM
SYS Temp: +38.4°C (high = +146°C, hyst = -71°C)
CPU Temp: +52.6°C (high = +146°C, hyst = -71°C)
SBr Temp: +23.1°C (high = +65°C, hyst = +60°C)
Athlon cooling: How about installing some Athlon cooling software?
Athcool runs fine here.
After all installs, I apt-getted X and kde. Its running quite ok.
Install logs and other status info is available in
/var/log/debian-installer/.
Once you have filled out this report, mail it to submit@bugs.debian.org.
Reply to: