Bug#269915: No IDE-Harddrives detected
Package: installation-reports
Severity: critical
Debian-installer-version: 03.09.2004
uname -a: Linux noiz 2.4.27-1-386 #1 Sun Aug 15 01:10:28 UTC 2004 i686 unknown
uname -a: Linux noiz 2.6.8-1-386 #1 Mon Aug 16 03:02:48 EDT 2004 i686 unknown
Date: 04.09.2004 10:18
Method: Networkinstall. Boot from daily ISO. Boot from /dev/hdd (CDROM)
Machine: x86 EPOX8KTA3+ (VIA)
Processor: AMD-TB1300
Memory: 640MB
Root Device: 2x IDE HITACHI 250BG, /dev/hd[ab]
Root Size/partition table: dmesg-output pastet below
Output of lspci and lspci -n: dmesg-output pastet below
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [E]
Partition hard drives: [ ]
Create file systems: [ ]
Mount partitions: [ ]
Install base system: [ ]
Install boot loader: [ ]
Reboot: [ ]
Comments/Problems:
I used the daily-netinst-ISO from 03.09.2004
I wanted to use "linux26"-Installation (easy, 2.6kernel). For debugging purposes
I also tried with "expert26" and "expert", with the same results.
When booting linux26 quite a lot hardware-modules are getting loaded, inclusive
for the HPT370 that is onboard, and where there are 2 disks on it. These disks
are quite _UN_important for this install.
On the main controller there are two 250GB-HITACHI-Disks, that are well detected
by the kernel, when modules are loaded, but are never seen by the d-i.
When booting in expert-modes, I only loaded the modules, I knew I would need.
Still the disks are available to the system (I can correctly do
fdisk -l /dev/discs/disc0/disc) but not seen by the installer.
Hence all the following fails.
I wanted to setup an RAID1 between the two disks and then create an LVM on
/dev/hd[ab]5
I'll paste the merged dmesg outputs of the "expert"-runs and /var/log/partman (which
is virtually the same for all runs).
On request I can support the complete /var/log of all the runs
I'll do another try with the official RC1 today, but I don't really have the time, to
do big testsuits, as I need to have this system running on Monday morning.
Jan
-----Begin DMESG--- booted "expert"----
Linux version 2.4.27-1-386 (joshk@trollwife) (gcc version 3.3.4 (Debian 1:3.3.4-7)) #1 Sun Aug 15 01:10:28 UTC 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000027ff0000 (usable)
BIOS-e820: 0000000027ff0000 - 0000000027ff3000 (ACPI NVS)
BIOS-e820: 0000000027ff3000 - 0000000028000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
639MB LOWMEM available.
On node 0 totalpages: 163824
zone(0): 4096 pages.
zone(1): 159728 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 VIA694 ) @ 0x000f7a30
ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x27ff3000
ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x27ff3040
ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
Kernel command line: DEBCONF_PRIORITY=low vga=normal initrd=/install/initrd.gz ramdisk_size=10240 root=/dev/rd/0 devfs=mount,dall rw -- BOOT_IMAGE=/install/vmlinuz DEBCONF_DEBUG=5 BOOT_DEBUG=1
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1302.964 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2601.77 BogoMIPS
Memory: 643080k/655296k available (1065k kernel code, 11832k reserved, 457k data, 96k init, 0k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: Common caps: 0183fbff c1c7fbff 00000000 00000000
CPU: AMD Athlon(tm) processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1302.9893 MHz.
..... host bus clock speed is 200.4598 MHz.
cpu: 0, clocks: 2004598, slice: 1002299
CPU0<T0:2004592,T1:1002288,D:5,S:1002299,C:2004598>
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfb4d0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co. <info@itc.hu>
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 2852k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
VFS: Mounted root (ext2 filesystem).
Trying to move old root to /initrd ... okay
Mounted devfs on /dev
Freeing unused kernel memory: 96k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 01:12:25 Aug 15 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:07.2
PCI: Sharing IRQ 5 with 00:07.3
usb-uhci.c: USB UHCI at I/O 0xa400, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:07.3
PCI: Sharing IRQ 5 with 00:07.2
usb-uhci.c: USB UHCI at I/O 0xa800, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver usbkbd
usbkbd.c: :USB HID Boot Protocol keyboard driver
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
hub.c: new USB device 00:07.2-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x46d/0xc00e) is not claimed by any active driver.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: HDS722525VLAT80, ATA DISK drive
hdb: HDS722525VLAT80, ATA DISK drive
hdd: HL-DT-ST RW/DVD GCC-4120B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 488397168 sectors (250059 MB) w/7938KiB Cache, CHS=30401/255/63
hdb: attached ide-disk driver.
hdb: 488397168 sectors (250059 MB) w/7938KiB Cache, CHS=30401/255/63
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 >
/dev/ide/host0/bus0/target1/lun0: p1 p2 p3 p4 < p5 >
hdd: attached ide-cdrom driver.
hdd: ATAPI 32X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.12
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
spurious 8259A interrupt: IRQ7.
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 10 for device 00:08.0
eth0: RealTek RTL8139 at 0xb800, 00:50:bf:2d:74:de, IRQ 10
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Journalled Block Device driver loaded
SGI XFS with ACLs, no debug enabled
SGI XFS Quota Management subsystem
-----End DMESG--- booted "expert"----
-----Begin DMESG--- booted "expert26"----
Linux version 2.6.8-1-386 (dilinger@toaster.hq.voxel.net) (gcc version 3.3.4 (Debian 1:3.3.4-7)) #1 Mon Aug 16 03:02:48 EDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000027ff0000 (usable)
BIOS-e820: 0000000027ff0000 - 0000000027ff3000 (ACPI NVS)
BIOS-e820: 0000000027ff3000 - 0000000028000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
639MB LOWMEM available.
On node 0 totalpages: 163824
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 159728 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 VIA694 ) @ 0x000f7a30
ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x27ff3000
ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x27ff3040
ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Built 1 zonelists
Kernel command line: DEBCONF_PRIORITY=low vga=normal initrd=/install/2.6/initrd.gz ramdisk_size=10240 root=/dev/rd/0 devfs=mount,dall rw -- BOOT_IMAGE=/install/2.6/vmlinuz DEBCONF_DEBUG=5 BOOT_DEBUG=1
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 1303.452 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 643204k/655296k available (1329k kernel code, 11328k reserved, 727k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2580.48 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: After vendor identify, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000020
CPU: AMD Athlon(tm) processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1302.0746 MHz.
..... host bus clock speed is 200.0422 MHz.
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 2801k freed
NET: Registered protocol family 16
EISA bus registered
spurious 8259A interrupt: IRQ7.
PCI: PCI BIOS revision 2.10 entry at 0xfb4d0, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbfb0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbfe0, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:07.3[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12
ACPI: PCI interrupt 0000:00:07.5[C] -> GSI 12 (level, low) -> IRQ 12
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 10 (level, low) -> IRQ 10
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Initializing Cryptographic API
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
VFS: Mounted root (ext2 filesystem).
Trying to move old root to /initrd ... okay
Mounted devfs on /dev
Freeing unused kernel memory: 204k freed
NET: Registered protocol family 1
ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:07.2: irq 5, io base 0000a400
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:07.3[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:07.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:07.3: irq 5, io base 0000a800
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
usb 1-1: new low speed USB device using address 2
vesafb: probe of vesafb0 failed with error -6
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb0: VGA16 VGA frame buffer device
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:07.2-1
Console: switching to colour frame buffer device 80x30
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:pio, hdd:DMA
hda: HDS722525VLAT80, ATA DISK drive
hdb: HDS722525VLAT80, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdd: HL-DT-ST RW/DVD GCC-4120B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 488397168 sectors (250059 MB) w/7938KiB Cache, CHS=30401/255/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 >
hdb: max request size: 1024KiB
hdb: 488397168 sectors (250059 MB) w/7938KiB Cache, CHS=30401/255/63, UDMA(100)
/dev/ide/host0/bus0/target1/lun0: p1 p2 p3 p4 < p5 >
hdd: ATAPI 32X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ISO 9660 Extensions: Microsoft Joliet Level 3
Unable to load NLS charset cp437
Unable to load NLS charset cp437
ISO 9660 Extensions: RRIP_1991A
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xb800, 00:50:bf:2d:74:de, IRQ 10
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 17
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
-----End DMESG--- booted "expert26"----
-----Begin /var/log/partman--- booted "expert"----
/bin/partman: *******************************************************
/lib/partman/init.d/01unsupported: *******************************************************
/lib/partman/init.d/30parted: *******************************************************
parted_server: ======= Starting the server
parted_server: main_loop: iteration 1
parted_server: Opening infifo
/lib/partman/init.d/30parted: IN: OPEN =dev=ide=host0=bus0=target0=lun0=disc /dev/ide/host0/bus0/target0/lun0/disc
parted_server: Read command: OPEN
parted_server: command_open()
parted_server: Request to open =dev=ide=host0=bus0=target0=lun0=disc
parted_server: Opening outfifo
parted_server: OUT: OK
parted_server: OUT: OK
parted_server: Note =dev=ide=host0=bus0=target0=lun0=disc as unchanged
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 2
parted_server: Opening infifo
/lib/partman/init.d/30parted: IN: OPEN =dev=ide=host0=bus0=target1=lun0=disc /dev/ide/host0/bus0/target1/lun0/disc
parted_server: Read command: OPEN
parted_server: command_open()
parted_server: Request to open =dev=ide=host0=bus0=target1=lun0=disc
parted_server: Opening outfifo
parted_server: OUT: OK
parted_server: OUT: OK
parted_server: Note =dev=ide=host0=bus0=target1=lun0=disc as unchanged
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 3
parted_server: Opening infifo
/lib/partman/init.d/31md-devices: *******************************************************
/lib/partman/init.d/35dump: *******************************************************
/lib/partman/init.d/35dump: IN: DUMP =dev=ide=host0=bus0=target0=lun0=disc
parted_server: Read command: DUMP
parted_server: command_dump()
parted_server: Opening outfifo
parted_server: OUT: OK
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 4
parted_server: Opening infifo
Device: yes
Model: HDS722525VLAT80
Path: /dev/ide/host0/bus0/target0/lun0/disc
Sector size: 512
Sectors: 488397168
Sectors/track: 63
Heads: 255
Cylinders: 30401
Partition table: yes
Type: msdos
Partitions: # id length type fs path name
(0,0,0) (0,0,62) -1 0-32255 32256 primary label /dev/ide/host0/bus0/target0/lun0/part-1
(0,1,0) (123,254,62) 1 32256-1019934719 1019902464 primary linux-swap /dev/ide/host0/bus0/target0/lun0/part1
(124,0,0) (147,254,62) 2 1019934720-1217341439 197406720 primary ext3 /dev/ide/host0/bus0/target0/lun0/part2
(148,0,0) (1363,254,62) 3 1217341440-11219281919 10001940480 primary reiserfs /dev/ide/host0/bus0/target0/lun0/part3
(1364,0,0) (30400,254,62) 4 11219281920-250056737279 238837455360 primary extended /dev/ide/host0/bus0/target0/lun0/part4
(1364,0,0) (1364,0,62) -1 11219281920-11219314175 32256 logical label /dev/ide/host0/bus0/target0/lun0/part-1
(1364,1,0) (30400,254,62) 5 11219314176-250056737279 238837423104 logical unknown /dev/ide/host0/bus0/target0/lun0/part5
(30401,0,0) (30401,80,62) -1 250056737280-250059350015 2612736 primary label /dev/ide/host0/bus0/target0/lun0/part-1
Dump finished.
/lib/partman/init.d/35dump: IN: DUMP =dev=ide=host0=bus0=target1=lun0=disc
parted_server: Read command: DUMP
parted_server: command_dump()
parted_server: Opening outfifo
parted_server: OUT: OK
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 5
parted_server: Opening infifo
Device: yes
Model: HDS722525VLAT80
Path: /dev/ide/host0/bus0/target1/lun0/disc
Sector size: 512
Sectors: 488397168
Sectors/track: 63
Heads: 255
Cylinders: 30401
Partition table: yes
Type: msdos
Partitions: # id length type fs path name
(0,0,0) (0,0,62) -1 0-32255 32256 primary label /dev/ide/host0/bus0/target1/lun0/part-1
(0,1,0) (123,254,62) 1 32256-1019934719 1019902464 primary linux-swap /dev/ide/host0/bus0/target1/lun0/part1
(124,0,0) (147,254,62) 2 1019934720-1217341439 197406720 primary ext3 /dev/ide/host0/bus0/target1/lun0/part2
(148,0,0) (1363,254,62) 3 1217341440-11219281919 10001940480 primary reiserfs /dev/ide/host0/bus0/target1/lun0/part3
(1364,0,0) (30400,254,62) 4 11219281920-250056737279 238837455360 primary extended /dev/ide/host0/bus0/target1/lun0/part4
(1364,0,0) (1364,0,62) -1 11219281920-11219314175 32256 logical label /dev/ide/host0/bus0/target1/lun0/part-1
(1364,1,0) (30400,254,62) 5 11219314176-250056737279 238837423104 logical unknown /dev/ide/host0/bus0/target1/lun0/part5
(30401,0,0) (30401,80,62) -1 250056737280-250059350015 2612736 primary label /dev/ide/host0/bus0/target1/lun0/part-1
Dump finished.
/lib/partman/init.d/50lvm: *******************************************************
/lib/partman/init.d/50lvm: IN: PARTITIONS =dev=ide=host0=bus0=target0=lun0=disc
parted_server: Read command: PARTITIONS
parted_server: command_partitions()
parted_server: Opening outfifo
parted_server: OUT: OK
parted_server: OUT: 1 32256-1019934719 1019902464 primary linux-swap /dev/ide/host0/bus0/target0/lun0/part1
parted_server: OUT: 2 1019934720-1217341439 197406720 primary ext3 /dev/ide/host0/bus0/target0/lun0/part2
parted_server: OUT: 3 1217341440-11219281919 10001940480 primary reiserfs /dev/ide/host0/bus0/target0/lun0/part3
parted_server: OUT: 5 11219314176-250056737279 238837423104 logical unknown /dev/ide/host0/bus0/target0/lun0/part5
parted_server: Partitions printed
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 6
parted_server: Opening infifo
/lib/partman/init.d/50lvm: IN: GET_FLAGS =dev=ide=host0=bus0=target0=lun0=disc 32256-1019934719
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(32256-1019934719)
parted_server: Partition found (32256-1019934719)
parted_server: OUT: OK
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 7
parted_server: Opening infifo
/lib/partman/init.d/50lvm: IN: GET_FLAGS =dev=ide=host0=bus0=target0=lun0=disc 1019934720-1217341439
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(1019934720-1217341439)
parted_server: Partition found (1019934720-1217341439)
parted_server: OUT: OK
parted_server: OUT: boot
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 8
parted_server: Opening infifo
/lib/partman/init.d/50lvm: IN: GET_FLAGS =dev=ide=host0=bus0=target0=lun0=disc 1217341440-11219281919
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(1217341440-11219281919)
parted_server: Partition found (1217341440-11219281919)
parted_server: OUT: OK
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 9
parted_server: Opening infifo
/lib/partman/init.d/50lvm: IN: GET_FLAGS =dev=ide=host0=bus0=target0=lun0=disc 11219314176-250056737279
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(11219314176-250056737279)
parted_server: Partition found (11219314176-250056737279)
parted_server: OUT: OK
parted_server: OUT: lvm
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 10
parted_server: Opening infifo
/lib/partman/init.d/50lvm: IN: PARTITIONS =dev=ide=host0=bus0=target1=lun0=disc
parted_server: Read command: PARTITIONS
parted_server: command_partitions()
parted_server: Opening outfifo
parted_server: OUT: OK
parted_server: OUT: 1 32256-1019934719 1019902464 primary linux-swap /dev/ide/host0/bus0/target1/lun0/part1
parted_server: OUT: 2 1019934720-1217341439 197406720 primary ext3 /dev/ide/host0/bus0/target1/lun0/part2
parted_server: OUT: 3 1217341440-11219281919 10001940480 primary reiserfs /dev/ide/host0/bus0/target1/lun0/part3
parted_server: OUT: 5 11219314176-250056737279 238837423104 logical unknown /dev/ide/host0/bus0/target1/lun0/part5
parted_server: Partitions printed
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 11
parted_server: Opening infifo
/lib/partman/init.d/50lvm: IN: GET_FLAGS =dev=ide=host0=bus0=target1=lun0=disc 32256-1019934719
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(32256-1019934719)
parted_server: Partition found (32256-1019934719)
parted_server: OUT: OK
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 12
parted_server: Opening infifo
/lib/partman/init.d/50lvm: IN: GET_FLAGS =dev=ide=host0=bus0=target1=lun0=disc 1019934720-1217341439
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(1019934720-1217341439)
parted_server: Partition found (1019934720-1217341439)
parted_server: OUT: OK
parted_server: OUT: boot
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 13
parted_server: Opening infifo
/lib/partman/init.d/50lvm: IN: GET_FLAGS =dev=ide=host0=bus0=target1=lun0=disc 1217341440-11219281919
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(1217341440-11219281919)
parted_server: Partition found (1217341440-11219281919)
parted_server: OUT: OK
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 14
parted_server: Opening infifo
/lib/partman/init.d/50lvm: IN: GET_FLAGS =dev=ide=host0=bus0=target1=lun0=disc 11219314176-250056737279
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(11219314176-250056737279)
parted_server: Partition found (11219314176-250056737279)
parted_server: OUT: OK
parted_server: OUT: lvm
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 15
parted_server: Opening infifo
/lib/partman/init.d/51md: *******************************************************
/lib/partman/init.d/51md: IN: PARTITIONS =dev=ide=host0=bus0=target0=lun0=disc
parted_server: Read command: PARTITIONS
parted_server: command_partitions()
parted_server: Opening outfifo
parted_server: OUT: OK
parted_server: OUT: 1 32256-1019934719 1019902464 primary linux-swap /dev/ide/host0/bus0/target0/lun0/part1
parted_server: OUT: 2 1019934720-1217341439 197406720 primary ext3 /dev/ide/host0/bus0/target0/lun0/part2
parted_server: OUT: 3 1217341440-11219281919 10001940480 primary reiserfs /dev/ide/host0/bus0/target0/lun0/part3
parted_server: OUT: 5 11219314176-250056737279 238837423104 logical unknown /dev/ide/host0/bus0/target0/lun0/part5
parted_server: Partitions printed
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 16
parted_server: Opening infifo
/lib/partman/init.d/51md: IN: GET_FLAGS =dev=ide=host0=bus0=target0=lun0=disc 32256-1019934719
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(32256-1019934719)
parted_server: Partition found (32256-1019934719)
parted_server: OUT: OK
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 17
parted_server: Opening infifo
/lib/partman/init.d/51md: IN: GET_FLAGS =dev=ide=host0=bus0=target0=lun0=disc 1019934720-1217341439
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(1019934720-1217341439)
parted_server: Partition found (1019934720-1217341439)
parted_server: OUT: OK
parted_server: OUT: boot
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 18
parted_server: Opening infifo
/lib/partman/init.d/51md: IN: GET_FLAGS =dev=ide=host0=bus0=target0=lun0=disc 1217341440-11219281919
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(1217341440-11219281919)
parted_server: Partition found (1217341440-11219281919)
parted_server: OUT: OK
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 19
parted_server: Opening infifo
/lib/partman/init.d/51md: IN: GET_FLAGS =dev=ide=host0=bus0=target0=lun0=disc 11219314176-250056737279
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(11219314176-250056737279)
parted_server: Partition found (11219314176-250056737279)
parted_server: OUT: OK
parted_server: OUT: lvm
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 20
parted_server: Opening infifo
/lib/partman/init.d/51md: IN: PARTITIONS =dev=ide=host0=bus0=target1=lun0=disc
parted_server: Read command: PARTITIONS
parted_server: command_partitions()
parted_server: Opening outfifo
parted_server: OUT: OK
parted_server: OUT: 1 32256-1019934719 1019902464 primary linux-swap /dev/ide/host0/bus0/target1/lun0/part1
parted_server: OUT: 2 1019934720-1217341439 197406720 primary ext3 /dev/ide/host0/bus0/target1/lun0/part2
parted_server: OUT: 3 1217341440-11219281919 10001940480 primary reiserfs /dev/ide/host0/bus0/target1/lun0/part3
parted_server: OUT: 5 11219314176-250056737279 238837423104 logical unknown /dev/ide/host0/bus0/target1/lun0/part5
parted_server: Partitions printed
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 21
parted_server: Opening infifo
/lib/partman/init.d/51md: IN: GET_FLAGS =dev=ide=host0=bus0=target1=lun0=disc 32256-1019934719
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(32256-1019934719)
parted_server: Partition found (32256-1019934719)
parted_server: OUT: OK
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 22
parted_server: Opening infifo
/lib/partman/init.d/51md: IN: GET_FLAGS =dev=ide=host0=bus0=target1=lun0=disc 1019934720-1217341439
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(1019934720-1217341439)
parted_server: Partition found (1019934720-1217341439)
parted_server: OUT: OK
parted_server: OUT: boot
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 23
parted_server: Opening infifo
/lib/partman/init.d/51md: IN: GET_FLAGS =dev=ide=host0=bus0=target1=lun0=disc 1217341440-11219281919
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(1217341440-11219281919)
parted_server: Partition found (1217341440-11219281919)
parted_server: OUT: OK
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 24
parted_server: Opening infifo
/lib/partman/init.d/51md: IN: GET_FLAGS =dev=ide=host0=bus0=target1=lun0=disc 11219314176-250056737279
parted_server: Read command: GET_FLAGS
parted_server: command_get_flags()
parted_server: Opening outfifo
parted_server: partition_with_id(11219314176-250056737279)
parted_server: Partition found (11219314176-250056737279)
parted_server: OUT: OK
parted_server: OUT: lvm
parted_server: OUT:
parted_server: Closing infifo and outfifo
parted_server: main_loop: iteration 25
parted_server: Opening infifo
/lib/partman/init.d/69no_media: *******************************************************
/bin/partman: IN: QUIT
parted_server: Read command: QUIT
parted_server: Quitting
-----End /var/log/partman--- booted "expert"----
Reply to: