Bug#267319: failed SATA installation of sarge (with net-inst CD of rc1 and also 2004/08/20)
Package: installation-reports
INSTALL REPORT
Debian-installer-version: netinst-iso as of 2004/08/20 and rc1
(http://cdimage.debian.org/pub/cdimage-testing/sarge_d-i/i386/)
uname -a: (was not possible)
Date: 21st August 2004
Method: CD-ROM (Net-Install-CD)
Machine: custom built with ASUS P4P 800 motherboard
Processor: Intel P4 2600 MHz
Memory: 512 MB
Root Device: 200 GB Segate Barracuda SATA (controller: Adaptec 1210SA)
Root Size/partition table:
(was not possible)
Output of lspci and lspci -n:
(from customized 2.6.8.1 kernel after install on standard IDE disk and bootup)
0000:00:00.0 Host bridge: Intel Corp. 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
0000:00:01.0 PCI bridge: Intel Corp. 82865G/PE/P PCI to AGP Controller (rev 02)
0000:00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1 (rev 02)
0000:00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2 (rev 02)
0000:00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3 (rev 02)
0000:00:1d.3 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4 (rev 02)
0000:00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2)
0000:00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Bridge (rev 02)
0000:00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) Ultra ATA 100 Storage Controller (rev 02)
0000:00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE]
0000:02:09.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 05)
0000:02:0b.0 RAID bus controller: Silicon Image, Inc. (formerly CMD Technology Inc) Adaptec AAR-1210SA SATA HostRAID Controller (rev 02)
0000:02:0d.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
0000:00:00.0 0600: 8086:2570 (rev 02)
0000:00:01.0 0604: 8086:2571 (rev 02)
0000:00:1d.0 0c03: 8086:24d2 (rev 02)
0000:00:1d.1 0c03: 8086:24d4 (rev 02)
0000:00:1d.2 0c03: 8086:24d7 (rev 02)
0000:00:1d.3 0c03: 8086:24de (rev 02)
0000:00:1d.7 0c03: 8086:24dd (rev 02)
0000:00:1e.0 0604: 8086:244e (rev c2)
0000:00:1f.0 0601: 8086:24d0 (rev 02)
0000:00:1f.1 0101: 8086:24db (rev 02)
0000:00:1f.3 0c05: 8086:24d3 (rev 02)
0000:01:00.0 0300: 1002:5159
0000:02:09.0 0200: 8086:1229 (rev 05)
0000:02:0b.0 0104: 1095:0240 (rev 02)
0000:02:0d.0 0200: 10b7:9200 (rev 78)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [ ]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [E]
Partition hard drives: [ ]
Create file systems: [ ]
Mount partitions: [ ]
Install base system: [ ]
Install boot loader: [ ]
Reboot: [ ]
Comments/Problems:
I've been booting with "linux26" and it was not possible to get SATA
the Adaptec 1210SA working at all. It hang at the hardware detection at
84% (ide-disk). When removing the SATA cables and just letting the
controller (PCI card) in, it hang at 81% (ide-generic).
After installation on a standard IDE disk and booting with the controller
plugged in, I get about 3 "lost interrupt" messages, then it detects the
SATA HDD's size, etc afterwards a couple of more "lost interrupt" messages.
When booting with a self-compiled 2.6.8.1 kernel (from www.kernel.org) it
works flawlessly with NO problems at all, so I assume this is a
KERNEL problem.
--
\|||/
(o o)
/------------ooO-(_)-Ooo------------------------\
| e-Mail: markus@linux-corner.net |
| homepage: www.linux-corner.net |
\-----------------------------------------------/
Reply to: