Bug#267279: installation report for sarge (rc1 + 2004/08/20)
Package: installation-reports
INSTALL REPORT
Debian-installer-version: netinst-iso as of 2004/08/20 and rc1
(http://cdimage.debian.org/pub/cdimage-testing/sarge_d-i/i386/)
uname -a: Linux sarge 2.6.7-1-386 #1 Thu Jul 8 05:08:04 EDT 2004 i686 GNU/Linux
Date: 21st August 2004
Method: CD-ROM (Net-Install-CD)
Machine: custom built with ASUS P4P 800 motherboard
Processor: Intel P4 2600 MHz
Memory: 512 MB
Root Device: 200 GB Segate Barracuda SATA (on-board Intel ICH5 controller)
Root Size/partition table:
Disk /dev/sda: 200.0 GB, 200049647616 bytes
255 heads, 63 sectors/track, 24321 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System Mount point
/dev/sda1 * 1 18 144553+ 83 Linux /
/dev/sda2 19 24321 195213847+ 5 Extended
/dev/sda5 19 626 4883728+ 83 Linux /usr
/dev/sda6 627 991 2931831 83 Linux /var
/dev/sda7 992 1040 393561 83 Linux /tmp
/dev/sda8 1041 24259 186506586 83 Linux /home
/dev/sda9 24260 24321 497983+ 82 Linux swap
Output of lspci and lspci -n:
0000:00:00.0 Host bridge: Intel Corp. 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
0000:00:01.0 PCI bridge: Intel Corp. 82865G/PE/P PCI to AGP Controller (rev 02)
0000:00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1 (rev 02)
0000:00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2 (rev 02)
0000:00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3 (rev 02)
0000:00:1d.3 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4 (rev 02)
0000:00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2)
0000:00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Bridge (rev 02)
0000:00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) Ultra ATA 100 Storage Controller (rev 02)
0000:00:1f.2 IDE interface: Intel Corp. 82801EB (ICH5) Serial ATA 150 Storage Controller (rev 02)
0000:00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE]
0000:02:09.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 05)
0000:02:0d.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
0000:00:00.0 0600: 8086:2570 (rev 02)
0000:00:01.0 0604: 8086:2571 (rev 02)
0000:00:1d.0 0c03: 8086:24d2 (rev 02)
0000:00:1d.1 0c03: 8086:24d4 (rev 02)
0000:00:1d.2 0c03: 8086:24d7 (rev 02)
0000:00:1d.3 0c03: 8086:24de (rev 02)
0000:00:1d.7 0c03: 8086:24dd (rev 02)
0000:00:1e.0 0604: 8086:244e (rev c2)
0000:00:1f.0 0601: 8086:24d0 (rev 02)
0000:00:1f.1 0101: 8086:24db (rev 02)
0000:00:1f.2 0101: 8086:24d1 (rev 02)
0000:00:1f.3 0c05: 8086:24d3 (rev 02)
0000:01:00.0 0300: 1002:5159
0000:02:09.0 0200: 8086:1229 (rev 05)
0000:02:0d.0 0200: 10b7:9200 (rev 78)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
1) As noted before, ipchains should IMHO not being installed by default,
because since 2.4 we can use iptables.
2) It would also be nice to have the posibility of controlling what
will be installed with a .conf file or something similar. Something
alike was possible with RedHat's installer when entering it at the
boot prompt of the installer.
Reply to: