Bug#259942: d-i dated 2004 07 13 failled to boot on a sparc sunblade 100
Package: debian-installer
Debian-installer-version: 2004 07 13 from
http://cdimage.debian.org/pub/cdimage-testing/sarge_d-i/sparc/
Machine: SunBlade 100
Hi all,
I am not very familiar with d-i and less with sparc arch but a
colleage of mine ask me to test a linux its sunblade :)
After the download of the woody the install start to failled becasue
of the know problem:
?Fast access MMU Miss.
I so try to download the sarges-netinstall.iso beta4 (May 2004) for
this platform but after ENTER to install the kernel (a 2.4.24 if a
read well) failled to boot because:
[...]
panic: no init found
Finaly I download the last sarges-netinstall.iso dated of this 2004
07 13 where the kernel (the 2.4.26) panic also because:
[...]
RAMDISK:Couldn't find valid RAM Disk image starting at 0.
...
Kernel panic: VFS: Unable to mount root fs.
On the m-l, 'Frederik Dannemare' advise also me to test:
<http://gluck.debian.org/cdimage/testing/sid_d-i/sparc/20040713/sarge-sparc-netinst.iso>
which failled to boot the same way.
The weird stuff came when I tried to boot with a serial console to collect dmesg, I couldn't anymore reproduce the pb?
Here is what I grab:
Initializing Memory...
ok boot cdrom
Boot device: /pci@1f,0/ide@d/cdrom@1,0:f File and args:
SILO Version 1.4.6
\
Welcome to Debian GNU/Linux sarge!
This is a Debian installation CDROM, built on 20040713.
Keep it once you have installed your system, as you can boot from it
to repair the system on your hard disk if that ever becomes necessary.
WARNING: You should completely back up all of your hard disks before
proceeding. The installation procedure can completely and irreversibly
erase them! If you haven't made backups yet, remove the rescue CD from
the drive and press L1-A to get back to the OpenBoot prompt.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted
by applicable law.
[ ENTER - Boot install ] [ Type "rescue" - Boot into rescue mode ]
boot:
Allocated 8 Megs of memory at 0x40000000 for kernel
|/-\[...]|/Loaded kernel version 2.4.26
Loading initial ramdisk (1858437 bytes at 0x7800000 phys, 0x40C00000 virt)...
-\|/[...]-\|/
Remapping the kernel... done.
Booting Linux...
PROMLIB: Sun IEEE Boot Prom 4.0.45 2001/02/08 14:33
Linux version 2.4.26-sparc64 (joshk@darjeeling.triplehelix.org) (gcc version
3.3.3 (Debian 20040321)) #1 Fri Jun 18 02:04:50 PDT 2004
ARCH: SUN4U
Ethernet address: 00:03:ba:10:e5:74
On node 0 totalpages: 15502
zone(0): 16270 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Found CPU 0 (node=f006dbd4,mid=0)
Found 1 CPU prom device tree node(s).
Kernel command line: root=/dev/rd/0 cdrom devfs=mount rw ramdisk_size=8192
rootfstype=ext2
Calibrating delay loop... 1002.70 BogoMIPS
Memory: 122440k available (2592k kernel code, 608k data, 184k init) [fffff80000000000,0000000007f1c000]
Dentry cache hash table entries: 16384 (order: 5, 262144 bytes)
Inode cache hash table entries: 8192 (order: 4, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 8192 bytes)
Buffer cache hash table entries: 1024 (order: 0, 8192 bytes)
Page-cache hash table entries: 16384 (order: 4, 131072 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing for controllers.
PCI: Found SABRE, main regs at 000001fe00000000, wsync at 000001fe00001c20
SABRE: Shared PCI config space at 000001fe01000000
SABRE: DVMA at c0000000 [20000000]
PCI-IRQ: Routing bus[ 0] slot[ 8] map[0] to INO[23]
PCI-IRQ: Routing bus[ 0] slot[ c] map[0] to INO[06]
PCI-IRQ: Routing bus[ 0] slot[ c] map[0] to INO[1c]
PCI-IRQ: Routing bus[ 0] slot[ c] map[0] to INO[24]
PCI-IRQ: Routing bus[ 0] slot[ d] map[0] to INO[0c]
PCI-IRQ: Routing bus[ 0] slot[13] map[0] to INO[0f]
PCI0(PBMA): Bus running at 33MHz
isa0: [dma -> (floppy) (parallel)] [power] [serial] [serial]
ebus0: [flashprom] [eeprom] [idprom]
PCIO serial driver version 1.54
su(serial) at 0x1fe020003f8 (tty 0 irq 12,7eb) is a 16550A
su(serial) at 0x1fe020002e8 (tty 1 irq 12,7eb) is a 16550A
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
rtc_init: no PC rtc found
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
sungem.c:v0.97 3/20/02 David S. Miller (davem@redhat.com)
eth%d: MII PHY ID: 437420 Enable Semiconductor
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:03:ba:10:e5:74
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 00:0d.0
ALI15X3: chipset revision 195
ALI15X3: 100% native mode on irq 4,7cc
ide0: BM-DMA at 0x1fe02000a20-0x1fe02000a27, BIOS settings: hda:pio,
hdb:pio
ide1: BM-DMA at 0x1fe02000a28-0x1fe02000a2f, BIOS settings: hdc:pio,
hdd:pio
hda: ST320011A, ATA DISK drive
hdb: PIONEER 16X DVD-ROM 1.21, ATAPI CD/DVD-ROM drive
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hdc: ST320011A, ATA DISK drive
ide0 at 0x1fe02000a00-0x1fe02000a07,0x1fe02000a1a on irq 4,7cc
ide1 at 0x1fe02000a10-0x1fe02000a17,0x1fe02000a0a on irq 4,7cc
hda: attached ide-disk driver.
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(66)
hdc: attached ide-disk driver.
hdc: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(66)
hdb: attached ide-cdrom driver.
hdb: ATAPI 40X DVD-ROM drive, 256kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.12
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p7 p8
/dev/ide/host0/bus1/target0/lun0: p3
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/usb-uhci.c: $Revision: 1.275 $ time 02:06:04 Jun 18 2004
host/usb-uhci.c: High bandwidth mode enabled
host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
host/usb-ohci.c: USB OHCI at membase 0x1ff02000000, IRQ 9,7e4
host/usb-ohci.c: usb-00:0c.3, PCI device 108e:1103
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 4 ports detected
usb.c: registered new driver usbmouse
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usb.c: registered new driver usbkbd
usbkbd.c: :USB HID Boot Protocol keyboard driver
mice: PS/2 mouse device common for all mice
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0 <====[*]
Freeing initrd memory: 1814k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
VFS: Mounted root (ext2 filesystem).
Trying to move old root to /initrd ... okay
Mounted devfs on /dev
Setting up filesUnimplemented SPARC system call 188
ystem, please waUnimplemented SPARC system call 188
it ...
Unimplemented SPARC system call 188
Unimplemented SPARC system call 188
Unimplemented SPARC system call 188
Unimplemented SPARC system call 188
Starting system log daemon: syslogd, klogd.
insmod: usb-ohci.o: no module by that name found
modprobe: failed to load module usb-ohci
insmod: usbkbd.o: no module by that name found
modprobe: failed to load module usbkbd
insmod: keybdev.o: no module by that name found
modprobe: failed to load module keybdev
insmod: usbserial.o: no module by that name found
modprobe: failed to load module usbserial
OTC when I go back to gfx console (the linux penguin appears well in the
uper left screen corner :-) )
all seems the same excepted that at <====[*] it failled like mentioned
in severall other bug report:
[...]
RAMDISK: Couldn't find valid RAM disk image starting at 0.
Freeing initrd memory: 1820k freed
Kernel panic: VFS: Unable to mount root fs on 00:00
Press L1-A to return to the boot prom
umm did we used the same ramdisk in the two case?
May be also interesting to know that it's the builtin gfx (no additional
gfx card?)
Thanks in advance for help,
Joel
Reply to: