|
Package: installation-reports Debian-installer-version: 07082004 uname -a: Linux Grundle 2.6.6-1-386 #1 Wed May 12 13:19:06 EST 2004
i686 GNU/Linux Date: 7-08-2004 22:00:00 Method: Network install from the download disk (link: http://cdimage.debian.org/pub/cdimage-testing/daily/i386/current/sarge-i386-netinst.iso.
I did a net install. No proxies. I booted from a cdrom drive (hda), from
ftp-mirror.internap.org. Machine: Whitebox supermicro Processor: 2x pIII slot 1 550mhz Memory: 886 Root Device: scsi /dev/sda (scsi0:A:0): 160.000MB/s transfers
(80.000MHz DT, offset 127, 16bit) Vendor: FUJITSU
Model: MAJ3091MP Rev: 0114 Type:
Direct-Access
ANSI SCSI revision: 04 scsi0:A:0:0: Tagged Queuing
enabled. Depth 8 Root Size/partition table: Disk /dev/sda: 9137 MB, 9137912832 bytes 255 heads, 63 sectors/track, 1110 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot
Start
End Blocks Id System /dev/sda1
*
1
30 240943+ 83 Linux ß \boot /dev/sda2
31 212
1461915 83 Linux ß swap /dev/sda3
213 1110
7213185 83 Linux ß \ Output of lspci: 0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX -
82443BX/ZX/DX Host bridge (rev 03) 0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX -
82443BX/ZX/DX AGP bridge (rev 03) 0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB
PIIX4 ISA (rev 02) 0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB
PIIX4 IDE (rev 01) 0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB
PIIX4 USB (rev 01) 0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4
ACPI (rev 02) 0000:00:0e.0 SCSI storage controller: Adaptec
AHA-2940U2/U2W / 7890/7891 0000:00:0f.0 Ethernet controller: 3Com Corporation
3CR990-TX-95 [Typhoon 56-bit] (rev 02) 0000:00:10.0 SCSI storage controller: Adaptec
AIC-7892A U160/m (rev 02) 0000:00:12.0 RAID bus controller: Silicon Image, Inc.
(formerly CMD Technology Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02) 0000:00:14.0 IDE interface: Silicon Image, Inc.
(formerly CMD Technology Inc) PCI0680 Ultra ATA-133 Host Controller (rev 01) 0000:01:00.0 VGA compatible controller: nVidia
Corporation NV5 [RIVA TNT2/TNT2 Pro] (rev 11) Base System Installation Checklist: Initial boot worked: [o ] Configure network HW: [o ] Config network: [o ] Detect
CD:
[o ] Load installer modules: [o ] Detect hard drives: [o ] Partition hard drives: [o ] Create file systems: [o ] Mount partitions: [o ] Install base system: [o ] Install boot loader: [e ] Reboot:
[o ] [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Comments/Problems: The install went relatively smoothly, except grub seems to want to boot
from hd2,0 instead of hd0,0 don’t know why I didn’t put 2,0 in
anywhere but it seems to want to boot from there. The other issue is that I want
to install my root on a sw raid5 md device, 3 scsi drives, but the installer
didn’t allow me to choose raid5 only 0,1. The last problem I have is that
I have my disks w/ persistent superblocks from another dist I had installed
(suse9.0) and for some reason this kernel is not auto-mounting them. I’m
playing w/ mdadm to get them all mounted up right now. Scary though because I have
data on one of the drive sets (170gb of data J). Other than
that it was pretty smooth and worked out well. Keep up the great work! |