Bug#238648: d-i, sata, netinst.iso 30.05.2004
--On Montag, 31. Mai 2004 15:42 -0300 Martin Michlmayr <tbm@cyrius.com>
wrote:
Can you boot debian-installer and manually load the module with:
modprobe sata_promise
Does debian-installer then see your disk?
d-i 30.05.2004 netinstall.
yes, I can 'modprobe sata_promise' in console 2 (alt-F2).
debian-installer sees the sata disk as /dev/sda.
Initially I had problems to install on this disk.
# configuring 'base-installer' failed with error code 1
last line in console 3 (alt-F3) was
setting up initrd-tools(0.1.69)
I got this error 3 times, reproducibly.
I switched the BIOS setting of the sata-controller
'onbord ATA device first' from "yes" to "no"
Then I entered the Promise Fast-Track setup during boot (ctrl-F)
and deleted the sata array and created a new one
(0+1 striping array - I have only one sata disk).
Now it works.
I switched 'onboard ATA device first' back from "no" to "yes"
because I didn't see any changes. It still works.
Maybe the Fast-track setup was the key ?!
I tried the following configurations and successfully installed Debian-base
-----------------
dev/sda1 /
-----------------
/dev/hda1 swap
/dev/hda2 /boot
/dev/hda3 /tmp
/dev/hda4 /var
/dev/hdb1 /home
/dev/sda1 /
-----------------
/dev/hda1 /usr
/dev/hdb1 /home
/dev/sda1 /boot
/dev/sda2 /
-----------------
I tried ext2, ext3, reiserfs.
Is there anything special I should test concerning SATA?
Otherwise I would put back the SATA disk into my P4P800.
If you need feedback, I could test sata in the P4P800 too.
Which module should I load for the ICH5R ?
The debain-installer does not see the sata disk automatically.
=====================================
From my scan through newsgroups etc. I got the impression
that sata uses ide commands rather than scsi commands,
with some scsi-like extensions to the ide set,
which are going to be implemented
but are not yet fully supported by sata controllers.
Consequently, I suppose that /dev/sda needs a scsi->ide translation
and /dev/hde should be the better choice.
- Am I completely wrong here?
- How would I address the sata disk (connected to a ICH5R) as /dev/hde?
=====================================
Can you paste the output of
lspci
lspci -n
Don't know if you still need the lspci from the P4PE.
Anyway, here it is.
btw: there is no lspci in the busybox.
This is the output from the installed debain.
++++++++++++++++++++++++++++++++++++++++++++
lspci
++++++++++++++++++++++++++++++++++++++++++++
0000:00:00.0 Host bridge: Intel Corp. 82845G/GL[Brookdale-G]/GE/PE DRAM
Controller/Host-Hub Interface (rev 02)
0000:00:01.0 PCI bridge: Intel Corp. 82845G/GL[Brookdale-G]/GE/PE
Host-to-AGP Bridge (rev 02)
0000:00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 (rev 02)
0000:00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 (rev 02)
0000:00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 (rev 02)
0000:00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI
Controller (rev 02)
0000:00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB/ER Hub interface to
PCI Bridge (rev 82)
0000:00:1f.0 ISA bridge: Intel Corp. 82801DB (ICH4) LPC Bridge (rev 02)
0000:00:1f.1 IDE interface: Intel Corp. 82801DB (ICH4) Ultra ATA 100
Storage Controller (rev 02)
0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBM (ICH4) SMBus Controller (rev 02)
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) AC'97
Audio Controller (rev 02)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV250
If [Radeon 9000] (rev 01)
0000:01:00.1 Display controller: ATI Technologies Inc Radeon RV250 [Radeon
9000] (Secondary) (rev 01)
0000:02:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80)
0000:02:04.0 RAID bus controller: Promise Technology, Inc. PDC20376 (rev 02)
0000:02:05.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5702
Gigabit Ethernet (rev 02)
0000:02:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 02)
0000:02:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio
Capture (rev 02)
++++++++++++++++++++++++++++++++++++++++++++
lspci -n
++++++++++++++++++++++++++++++++++++++++++++
0000:00:00.0 Class 0600: 8086:2560 (rev 02)
0000:00:01.0 Class 0604: 8086:2561 (rev 02)
0000:00:1d.0 Class 0c03: 8086:24c2 (rev 02)
0000:00:1d.1 Class 0c03: 8086:24c4 (rev 02)
0000:00:1d.2 Class 0c03: 8086:24c7 (rev 02)
0000:00:1d.7 Class 0c03: 8086:24cd (rev 02)
0000:00:1e.0 Class 0604: 8086:244e (rev 82)
0000:00:1f.0 Class 0601: 8086:24c0 (rev 02)
0000:00:1f.1 Class 0101: 8086:24cb (rev 02)
0000:00:1f.3 Class 0c05: 8086:24c3 (rev 02)
0000:00:1f.5 Class 0401: 8086:24c5 (rev 02)
0000:01:00.0 Class 0300: 1002:4966 (rev 01)
0000:01:00.1 Class 0380: 1002:496e (rev 01)
0000:02:03.0 Class 0c00: 1106:3044 (rev 80)
0000:02:04.0 Class 0104: 105a:3376 (rev 02)
0000:02:05.0 Class 0200: 14e4:16a6 (rev 02)
0000:02:0a.0 Class 0400: 109e:036e (rev 02)
0000:02:0a.1 Class 0480: 109e:0878 (rev 02)
++++++++++++++++++++++++++++++++++++++++++++
best regards
Markus Haiml
Reply to: