Re: Sarge install -- still no ACPI
Martin Michlmayr wrote:
Herbert, can you take a look at this? The same happens with 2.6. The
whole thread starts at
http://lists.debian.org/debian-boot/2004/05/msg01939.html
Mike, can you post the kernel output (dmesg) when booting with
acpi=off.
See attachment. This is with kernel 2.6.6-1-686.
Linux version 2.6.6-1-686 (herbert@gondolin) (gcc version 3.3.3 (Debian 20040401)) #1 Wed May 12 14:57:57 EST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bef0000 (usable)
BIOS-e820: 000000001bef0000 - 000000001beff000 (ACPI data)
BIOS-e820: 000000001beff000 - 000000001bf00000 (ACPI NVS)
BIOS-e820: 000000001bf00000 - 000000001c000000 (reserved)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
446MB LOWMEM available.
On node 0 totalpages: 114416
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 110320 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
Built 1 zonelists
Kernel command line: root=/dev/hda9 ro acpi=off
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 2120.092 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 446224k/457664k available (1506k kernel code, 10688k reserved, 639k data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4194.30 BogoMIPS
Security Scaffold v1.0.0 initialized
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD mobile AMD Athlon(tm) XP2800+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2119.0859 MHz.
..... host bus clock speed is 264.0982 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4504k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd87b, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f72c0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xa0e7, dseg 0x400
spurious 8259A interrupt: IRQ7.
pnp: 00:00: ioport range 0x370-0x371 has been reserved
pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0b: ioport range 0x40b-0x40b has been reserved
pnp: 00:0b: ioport range 0x480-0x48f has been reserved
pnp: 00:0b: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:0b: ioport range 0x8000-0x803f has been reserved
pnp: 00:0b: ioport range 0x8040-0x807f has been reserved
PnPBIOS: 18 nodes reported by PnP BIOS; 18 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using ALI IRQ Router
PCI: Using IRQ router ALI [10b9/1533] at 0000:00:07.0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 3 for device 0000:00:08.0
ttyS47 at I/O 0x8828 (irq = 3) is a 8250
ttyS1 at I/O 0x8840 (irq = 3) is a 8250
ttyS2 at I/O 0x8850 (irq = 3) is a 8250
ttyS3 at I/O 0x8860 (irq = 3) is a 8250
ttyS4 at I/O 0x8870 (irq = 3) is a 8250
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
i8042.c: Detected active multiplexing controller, rev 10.12.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4504 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Warning: ATI Radeon IGP Northbridge is not yet fully tested.
ALI15X3: IDE controller at PCI slot 0000:00:10.0
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8080-0x8087, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x8088-0x808f, BIOS settings: hdc:pio, hdd:pio
hda: ST94011A, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4241N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 p12 >
ext3: No journal on filesystem on hda9
ext3: No journal on filesystem on hda9
Adding 393532k swap on /dev/hda6. Priority:-1 extents:1
Real Time Clock Driver v1.12
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
NTFS driver 2.1.8 [Flags: R/O MODULE].
NTFS volume version 3.1.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Assigned IRQ 11 for device 0000:00:0a.0
Yenta: CardBus bridge found at 0000:00:0a.0 [103c:0024]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x01111112, devctl 0x64
Yenta: ISA IRQ mask 0x06f8, PCI irq 11
Socket status: 30000006
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker <becker@scyld.com>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Found IRQ 11 for device 0000:00:12.0
eth0: NatSemi DP8381[56] at 0xdc897000, 00:0e:7f:70:87:7a, IRQ 11.
Trident 4DWave/SiS 7018/ALi 5451,Tvia CyberPro 5050 PCI Audio, version 0.14.10j-2.6, 16:00:35 May 12 2004
PCI: Found IRQ 5 for device 0000:00:06.0
trident: ALi Audio Accelerator found at IO 0x8400, IRQ 5
ac97_codec: AC97 Modem codec, id: CXT41 (Unknown)
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Ati IGP320/M chipset
agpgart: Maximum main memory to use for agp memory: 379M
agpgart: AGP aperture is 64M @ 0xd4000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Assigned IRQ 9 for device 0000:00:02.0
ohci_hcd 0000:00:02.0: ALi Corporation USB 1.1 Controller
ohci_hcd 0000:00:02.0: irq 9, pci mem dc9bb000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
usb 1-1: new low speed USB device using address 2
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:02.0-1
usbcore: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
NET: Registered protocol family 17
Reply to: