Bug#238808: Package: installation-reports

[Yvette <yvette@zek7.com>]

Package: installation-reports

Debian-installer-version: 
2004-03-14
http://http.us.debian.org/debian/dists/testing/main/installer-i386/current/images/floppy/boot.img

uname -a: 
Linux milo 2.6.3-1-686-smp #2 SMP Tue Feb 24 20:29:08 EST 20


Date: 
2004-03-18 20:15

Method:
Boot from floppy
Network install from ftp.us.debian.org

Machine:
IBM xSeries 235
Processor:

Dual PIII 2.4 Xeon Processors

Memory:
2048 MB

Root Device: 
scsi0 : IBM PCI ServeRAID 7.00.00  Build 475 <ServeRAID 5i>
/dev/sda

Root Size/partition table: 

/dev/sda1            8642        8885     1952244   82  Linux swap
/dev/sda2   *           1          61      488029+  83  Linux
/dev/sda3              62         488     3416427   83  Linux
/dev/sda4             489        8641    65232153   83  Linux


/dev/sda4             65230132    293372  64936760   1% /
/dev/sda2               457341     17232    415708   4% /boot
/dev/sda3              3416272     36492   3379780   2% /var/log
tmpfs                  1036616         0   1036616   0% /dev/shm


Output of lspci:

00:00.0 Host bridge: ServerWorks CMIC-LE (rev 13)
00:00.1 Host bridge: ServerWorks CMIC-LE
00:00.2 Host bridge: ServerWorks: Unknown device 0000
00:09.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
00:0f.0 Host bridge: ServerWorks CSB5 South Bridge (rev 93)
00:0f.1 IDE interface: ServerWorks CSB5 IDE Controller (rev 93)
00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev 05)
00:0f.3 ISA bridge: ServerWorks GCLE Host Bridge
00:10.0 Host bridge: ServerWorks: Unknown device 0101 (rev 03)
00:10.2 Host bridge: ServerWorks: Unknown device 0101 (rev 03)
00:11.0 Host bridge: ServerWorks: Unknown device 0101 (rev 03)
00:11.2 Host bridge: ServerWorks: Unknown device 0101 (rev 03)
02:08.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5703 Gigabit Ethernet (rev 02)
05:03.0 RAID bus controller: IBM ServeRAID Controller

Base System Installation Checklist:

Initial boot worked:    [O]
Configure network HW:   [O]
Config network:         [O]
Detect CD:              [ ]
Load installer modules: [O]
Detect hard drives:     [O]
Partition hard drives:  [O]
Create file systems:    [O]
Mount partitions:       [O]
Install base system:    [O]
Install boot loader:    [O]
Reboot:                 [O]
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it

Comments/Problems:

I did the install off of just boot.img and root.img - there were no problems
with the scsi or the NIC (eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:02:55:07:17:41).


I've done the install twice (just for fun) and tried to accept all the defaults 
(except for loading additional drivers, and setting up the partition table), just
to see what happened. The original boot to:

vmlinuz-2.4.25-1-386

Was fine. I also grabbed:

vmlinuz-2.6.3-1-686-smp

and had no problems booting. 


Now I'm running off of:

vmlinuz-2.4.25-1-686-smp


Thanks!