[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#237777: Package: installation-reports for beta2



Package: installation-reports

Debian-installer-version: 13-Mar-2004
http://gluck.debian.org/cdimage/testing/sarge_d-i/i386/beta2/sarge- i386-netinst.iso
uname -a: Linux gandalf 2.4.22-1-386
Date: 13-Mar-2004 1800-2100
Method: from CD (see above)

Base System Installation Checklist:

Initial boot worked:    [O]
Configure network HW:   [O]
Config network:         [O]
Detect CD:              [O]
Load installer modules: [O]
Detect hard drives:     [O]
Partition hard drives:  [O]
Create file systems:    [O]
Mount partitions:       [O]
Install base system:    [O]
Install boot loader:    [O]
Reboot:                 [O]
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it

Comments/Problems:

Debian Installer beta2 comments

Hello,

X means improvements can be done, rest are explanaitions what was done

  I have an already installed HD in my computer as IDE1 slave
  I had to install a new debian because of HD crash
  I partitioned IDE1 master
X examples of partitions need to be given in the installation manual
X http://d-i.alioth.debian.org/manual/en.i386/index.html chapter 7.2, 7.3 e.g I have finally used for my 120GB disk 100MB /, 5GB /usr, 110GB /home,
  3000 /var, 50MB /tmp, 1000 swap, all ext2 except /home ext3, it saves
1 hour surfing to find out useful partion schemes and for unexperienced users
  the switch to RedHat, Suse or whatwever
X in installation manual (see above) /boot is not mentioned but dring the
  installation process it appears (assigning names to partitions),
a very useful hint which shed some light for me on the / and /boot issue I
  found in the RedHat installation manual:
	Caution
	While partitioning your hard drive, keep in mind that the BIOS in some
older systems cannot access more than the first 1024 cylinders on a hard drive. If this is the case, leave enough room for the /boot Linux partition on the first 1024 cylinders of your hard drive to boot Linux. The other Linux
	partitions can be after cylinder 1024.

If your hard drive is more than 1024 cylinders, you may need to create a /boot partition if you want the /(root) partition to use all of the remaining
	space on your hard drive.

X a screen shot of the finalized partition table in cfdisk is needed so nobody has to surf the internet to find out why only four partitions can be used (if you use
  only primary), what needs to be bootable, swap,...

  On screen:
  [!!] Configure and mount partitions,
  Select a partition:
X What is MiB and GiB??? You mean probably MB and GB

  In the same list my already formatted IDE 1 slave is mentioned,
to avoid that it will be overwritten I selected 'Leave the file system intact' but in the lists looks afterwards exactly as the other partitions on IDE1 master
  selecting 'Finish' I get asked on the next screen:
  'Ready to create file systems and mount partitions?'
at which point it was not clear to me if my formatted IDE1 slave will survive,
  I decided to switch off the computer deconnect the HD and start again
X If 'leave filesystem intact' is choosen it has to be explicitly mentioned in the X partitioins list to make clear that it will NOT be formatted (what is hopefully
  the case, didn't test to not risk my backup)

X no feedback during formatting, a hint at the beginning (if no proress bar is
  possible) that it might take some minutes would beuseful

X having the possibility to use GRUB instead of LILO would be nice

X no offer to make a boot floppy

X after reboot it was only possible to get via cancel out of the 'Apt Configuration' screen, seemed like an endless loop, but apparently all selections are written
  into sources.list, does really not become clear

Thanks a lot for the nice Debian and Keep up the good work!!!

Helge




Reply to: