Package: installation
Version: sarge/testing
Platform is Intel PR440FX, dual PPro 200/512, 2 x Intel i82557 ethernet controllers.
1) Boot Sarge netinstall cd downloaded 11/18/2003.
2) Run through install screens through loading components of Debian installer->detecting hardware->load modules.
3) Immediately after the load modules screen clears, I get a screen that says "Feel free to retry" & "continue".
4) Hit continue. Trying to manually configure network either statically or through DHCP results in "Feel free to retry".
Lsmod shows e100 module loaded: e100 40968 0 (unused)
Attempt to insmod e100 results in "A module named e100 already exists"
Ifconfig -a shows unconfigured eth0 & eth1 interfaces
Please find attached an lspci & dmesg from the Linux (non-Debian) install currently on the box.
P.S. - The curses screen with the error is incorrectly draw as well. The right side of the dialog box is broken.
-----
lspci -v -v
-----
00:00.0 Host bridge: Intel Corp. 440FX - 82441FX PMC [Natoma] (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
00:06.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (2000ns min, 14000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at ffbec000 (32-bit, prefetchable) [size=4K]
Region 1: I/O ports at ef80 [size=32]
Region 2: Memory at fed00000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
00:07.0 ISA bridge: Intel Corp. 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371SB PIIX3 IDE [Natoma/Triton II] (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at ffa0 [size=16]
00:09.0 SCSI storage controller: Adaptec AIC-7880U
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at f800 [disabled] [size=256]
Region 1: Memory at ffbed000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
00:0b.0 RAID bus controller: Mylex Corporation DAC960PD (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 40 (1000ns min), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at fc80 [size=128]
Region 1: Memory at ffbefc00 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=32K]
00:0f.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (2000ns min, 14000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at ffbee000 (32-bit, prefetchable) [size=4K]
Region 1: I/O ports at ff80 [size=32]
Region 2: Memory at ff800000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
00:11.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01) (prog-if 00 [VGA])
Subsystem: S3 Inc. ViRGE/DX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 40 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=64M]
Expansion ROM at <unassigned> [disabled] [size=64K]
-----
dmesg (from SuSE)
-----
Linux version 2.4.20-64GB-SMP (root@SMP_X86.suse.de) (gcc version 3.3 20030226 (prerelease) (SuSE Linux)) #1 SMP Wed Aug 6 18:30:02 UTC 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 0000000000100000 - 0000000010000000 (usable)
BIOS-e820: 00000000fec00000 - 00000000fec09000 (reserved)
BIOS-e820: 00000000ffe80000 - 0000000100000000 (reserved)
Scanning bios EBDA for MXT signature
0MB HIGHMEM available.
256MB LOWMEM available.
ACPI: have wakeup address 0xc0002000
found SMP MP-table at 000f7ef0
hm, page 000f7000 reserved twice.
hm, page 000f8000 reserved twice.
hm, page 000f7000 reserved twice.
hm, page 000f8000 reserved twice.
On node 0 totalpages: 65536
zone(0): 4096 pages.
zone(1): 61440 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 98 and too old
You can enable it with acpi=force
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: INTEL Product ID: PR440FX APIC at: 0xFEC08000
Processor #0 Pentium(tm) Pro APIC version 17
Processor #12 Pentium(tm) Pro APIC version 17
I/O APIC #13 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Building zonelist for node : 0
Kernel command line: root=/dev/rd/c0d0p3 vga=0x314 splash=silent showopts
bootsplash: silent mode.
Initializing CPU#0
Detected 198.669 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 396.49 BogoMIPS
Memory: 252392k/262144k available (1856k kernel code, 7188k reserved, 592k data, 184k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 8K, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0000fbff 00000000 00000000 00000000
CPU: Common caps: 0000fbff 00000000 00000000 00000000
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 8K, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0000fbff 00000000 00000000 00000000
CPU: Common caps: 0000fbff 00000000 00000000 00000000
CPU0: Intel Pentium Pro stepping 07
per-CPU timeslice cutoff: 1467.70 usecs.
task migration cache decay timeout: 10 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000040
ESR value after enabling vector: 00000000
Booting processor 1/12 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 396.49 BogoMIPS
CPU: L1 I cache: 8K, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: 0000fbff 00000000 00000000 00000000
CPU: Common caps: 0000fbff 00000000 00000000 00000000
CPU1: Intel Pentium Pro stepping 07
Total of 2 processors activated (792.98 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 13 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 13 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 13-0, 13-2, 13-10, 13-11, 13-13, 13-19, 13-20, 13-21, 13-22, 13-23 not connected.
..TIMER: vector=0x31 pin1=-1 pin2=0
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
number of MP IRQ sources: 17.
number of IO-APIC #13 registers: 24.
testing the IO APIC.......................
IO APIC #13......
.... register #00: 0D000000
....... : physical APIC id: 0D
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 0 0 0 0 0 1 1 31
01 003 03 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 0 0 0 0 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 003 03 0 0 0 0 0 1 1 71
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 79
0d 000 00 1 0 0 0 0 0 0 00
0e 003 03 0 0 0 0 0 1 1 81
0f 003 03 0 0 0 0 0 1 1 89
10 003 03 1 1 0 1 0 1 1 91
11 003 03 1 1 0 1 0 1 1 99
12 003 03 1 1 0 1 0 1 1 A1
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:0
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 198.6570 MHz.
..... host bus clock speed is 66.2187 MHz.
cpu: 0, clocks: 662187, slice: 220729
CPU0<T0:662176,T1:441440,D:7,S:220729,C:662187>
cpu: 1, clocks: 662187, slice: 220729
CPU1<T0:662176,T1:220704,D:14,S:220729,C:662187>
checking TSC synchronization across CPUs: passed.
migration_task 0 on cpu=0
migration_task 1 on cpu=1
ACPI: Subsystem revision 20030228
ACPI: Disabled via command line (acpi=off)
PCI: PCI BIOS revision 2.10 entry at 0xfda11, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI->APIC IRQ transform: (B0,I6,P0) -> 18
PCI->APIC IRQ transform: (B0,I9,P0) -> 17
PCI->APIC IRQ transform: (B0,I11,P0) -> 16
PCI->APIC IRQ transform: (B0,I15,P0) -> 17
PCI->APIC IRQ transform: (B0,I17,P0) -> 18
Limiting direct PCI/PCI transfers.
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
mxt_scan_bios: enter
Starting kswapd
bigpage subsystem: allocated 0 bigpages (=0MB).
kinoded started
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 16384
aio_setup: sizeof(struct page) = 48
vesafb: framebuffer at 0xf8000000, mapped to 0xd080d000, size 4096k
vesafb: mode is 800x600x16, linelength=1600, pages=3
vesafb: protected mode interface info at c000:5b6a
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture... no good signature found.
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 16 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX3: IDE controller at PCI slot 00:07.1
PIIX3: chipset revision 0
PIIX3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
hda: CRD-8320B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 549k freed
VFS: Mounted root (ext2 filesystem).
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.29
<Adaptec aic7880 Ultra SCSI adapter>
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
blk: queue c14ce618, I/O limit 4095Mb (mask 0xffffffff)
DAC960: ***** DAC960 RAID Driver Version 2.4.20aa1 of 4 December 2002 *****
DAC960: Copyright 1998-2001 by Leonard N. Zubkoff <lnz@dandelion.com>
DAC960#0: Configuring Mylex DAC960PL PCI RAID Controller
DAC960#0: Firmware Version: 3.52-0-02, Channels: 2, Memory Size: 16MB
DAC960#0: PCI Bus: 0, Device: 11, Function: 0, I/O Address: 0xFC80
DAC960#0: PCI Address: 0xFFBEFC00 mapped at 0xD0C10C00, IRQ Channel: 16
DAC960#0: Controller Queue Depth: 64, Maximum Blocks per Command: 128
DAC960#0: Driver Queue Depth: 63, Scatter/Gather Limit: 17 of 17 Segments
DAC960#0: Stripe Size: 64KB, Segment Size: 8KB, BIOS Geometry: 255/63
DAC960#0: Physical Devices:
DAC960#0: 0:0 Vendor: SEAGATE Model: ST34573W Revision: 6244
DAC960#0: Serial Number: LN80937300007914HKCS
DAC960#0: Disk Status: Online, 8888320 blocks
DAC960#0: 1:1 Vendor: SEAGATE Model: ST34573W Revision: 6244
DAC960#0: Serial Number: LN80919600007922H612
DAC960#0: Disk Status: Online, 8888320 blocks
DAC960#0: Logical Drives:
DAC960#0: /dev/rd/c0d0: RAID-0, Online, 17776640 blocks, Write Thru
Partition check:
rd/c0d0: rd/c0d0p1 rd/c0d0p2 rd/c0d0p3
reiserfs: found format "3.6" with standard journal
reiserfs: enabling write barrier flush mode
reiserfs: using ordered data mode
reiserfs: checking transaction log (dac960(48,3)) for (dac960(48,3))
Warning, log replay starting on readonly filesystem
reiserfs: replayed 2 transactions in 3 seconds
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 184k freed
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Adding Swap: 658656k swap-space (priority 42)
Intel(R) PRO/100 Network Driver - version 2.1.29-k3
Copyright (c) 2002 Intel Corporation
e100: selftest OK.
e100: eth0: Intel(R) 8255x-based Ethernet Adapter
e100: selftest OK.
e100: eth1: Intel(R) 8255x-based Ethernet Adapter
e100: eth0 NIC Link is Up 100 Mbps Half duplex
raw1394: /dev/raw1394 device initialized
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
isapnp: Scanning for PnP cards...
isapnp: Card 'CS4236B Audio'
isapnp: 1 Plug & Play card detected total
eth0: no IPv6 routers present