Hi,
First of all, why do you think network is the bottleneck?
Thank you for your concern.
If i run a specific job in a single system (without parallel) it
showed three months (aprox) time in a quad core processor. When i did
parallel using four systems it showed October 2015. I was using 100
Mpbs (ip time router). I have conformed that all the systems uses the
processors [using "top" command]. After that TooMeeK point out i have
to use "Gigabit routing switch supporting layer 3". I dont have that
switch in our lab. However, we had Netgear GS608 1000 Mpbs switch it
reduced the time (Feb 2015). Moreover, I read the link
http://cs.boisestate.edu/~amit/research/beowulf/beowulf-setup.pdf [6]
suggested by TooMeek. They have also suggested that Network switch is
important. Also, I saw few videos in youtube about layer 3 switch
capabilities. Therefore, I am convinced that "Gigabit routing switch
supporting layer 3" will solve this issue.
regards
Suresh
On Tue, Oct 14, 2014 at 4:40 AM, Rogerio Bastos
<writeme@rogeriobastos.eti.br> wrote:
First of all, why do you think network is the bottleneck?
Be sure of this before spend money with network equipments!
On 2014-10-07 00:50, suresh kannan wrote:
I am an Indian student in suwon, korea. I built a Beowulf cluster
(system information below) with four systems in our lab for our
simulation work with the help of good tutorials. In those
tutorials
they have mentioned all the system should have static ip
addresses.
Unfortunately, in all our labs we have been provided with dynamic
ip
address[5 ips for 15 members in three separate labs]. I have
requested
four more ip's from our university system admin. Due to the
language
problems, i conveyed the requirement through my korean lab mate
and i
dont know the reason why he denied us the static ip. So i found
another way to skip this procedure
http://www.reddit.com/r/linuxquestions/comments/2gubad/why_static_ip_address_is_necessary_for_linux/
[1]
[1].
Someone suggested to use a router (one static ip) and set static
ip
for the four computers through a router. I did that and it
worked.
However, the cluster is very slow. For instance If i submit my
simulation job in a single computer [4 core processor], it takes
2
months to complete a specific job. Although, if i connect 4
systems it
shows it take 6 months to complete the same job. It is actually
using
10 core processor [3,3,2,2-100% each]. I used TOP command to see
how
much processor the head and other nodes are using. I have used
openMPI
to do parallel the systems. I am using GROMACS (Parallelization
based
on MPI has been part of this software). I followed a parallel
configuration for the Gromacs with the help of this tutorial
http://flakrat.blogspot.kr/2013/04/how-to-compile-gromacs-461-with-openmpi.html
[2]
[2]. After reading few posts
http://www.reddit.com/r/linuxquestions/comments/2gbgbg/what_would_be_the_best_linux_distro_for_folding/
[3]
[3] i suspected the network router might be an issue.
Can you suggest me how can i troubleshoot this problem? Some one
suggested to use 2 network ports and make linux as a router and
use a
gigabitswitch to get the speed. However, we dont have 2 network
ports
system. If this is compulsory i can buy network ports (USB one).
Where do i start now?
Can i make my head node as a router and use USB network port (for
the
second network port) and connect to a gigabitswitch (any model
suggestion?) to connect other nodes. I dont know much about
networking
stuffs. It will be helpful if any experts can suggest to
troubleshoot
this issue.
Thank you for your time.
regards
Suresh
System Informations
Head node Processor : Intel core i3
RAM : 1 GB
No. of processor : 4
Network cards : 03:00.0 Ethernet controller: Realtek
Semiconductor
Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet
Controller
(rev 06)
System company : Samsung
Architecture : x86_64
OS flavour : Linux Mint 17 Qiana
Node1 Processor : Intel Quad core
RAM : 3 GB
No. of processor : 4
Network cards : 03:00.0 Ethernet controller: Realtek
Semiconductor
Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet
Controller
(rev 02)
System company : TG DREAMSYS
Architecture : x86_64
OS flavour : Linux Mint 17 Qiana
Node2 Processor : Intel core i3
RAM : 1 GB
No. of processor : 4
Network cards : 03:00.0 Ethernet controller: Realtek
Semiconductor
Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet
Controller
(rev 06)
System company : Samsung Architecture : x86_64
OS flavour : Linux Mint 17 Qiana
Node3 Processor : Intel core i3
RAM : 1 GB
No. of processor : 2 Network cards : 02:00.0 Ethernet controller
:
Qualcomm Atheros Attansic L2 Fast Ethernet (rev a0)
System company : JOOYONTECH
Architecture : x86_64
OS flavour : Linux Mint 17 Qiana
Router Company : ipTIME N604R
Maximum speed : 160Mbps (LAN to WAN)
Links:
------
[1]
http://www.reddit.com/r/linuxquestions/comments/2gubad/why_static_ip_address_is_necessary_for_linux/
[1]
[2]
http://flakrat.blogspot.kr/2013/04/how-to-compile-gromacs-461-with-openmpi.html
[2]
[3]
http://www.reddit.com/r/linuxquestions/comments/2gbgbg/what_would_be_the_best_linux_distro_for_folding/
[3]
--
My email was sent by May First/People Link
https://mayfirst.org [4]
--
To UNSUBSCRIBE, email to debian-beowulf-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact
listmaster@lists.debian.org
Archive:
[🔎] 40cfbd085315754eb7f15af3a3dfc943@mail.mayfirst.org">https://lists.debian.org/[🔎] 40cfbd085315754eb7f15af3a3dfc943@mail.mayfirst.org
[5]
Links:
------
[1]
http://www.reddit.com/r/linuxquestions/comments/2gubad/why_static_ip_address_is_necessary_for_linux/
[2]
http://flakrat.blogspot.kr/2013/04/how-to-compile-gromacs-461-with-openmpi.html
[3]
http://www.reddit.com/r/linuxquestions/comments/2gbgbg/what_would_be_the_best_linux_distro_for_folding/
[4] https://mayfirst.org
[5]
[🔎] 40cfbd085315754eb7f15af3a3dfc943@mail.mayfirst.org">https://lists.debian.org/[🔎] 40cfbd085315754eb7f15af3a3dfc943@mail.mayfirst.org
[6] http://cs.boisestate.edu/%7Eamit/research/beowulf/beowulf-setup.pdf