Re: NSLU2 Lenny install problem
>>Also, since you said you wanted ohci and not ehci, why don't you boot
>>again with your firmware (that apparently loads ohci) after moving
>>away the ehci module on disk.
>I'll try that right away.
First the nslu got stuck at:
Setting the system clock.
After removing the battery for a while I tried again:
....
Setting the system clock.
Activating swap...[42949407.700000] Adding 248968k swap on /dev/sda5.
Priority:-1 extents:1 across:248968k
done.
Checking root file system...fsck 1.41.3 (12-Oct-2008)
e2fsck 1.41.3 (12-Oct-2008)
Superblock last mount time is in the future. Fix? yes
Superblock last write time is in the future. Fix? yes
/dev/sda2 has filesystem last checked time in the future, check forced.
Pass 1: Checking inodes, blocks, and sizes
/dev/sda2: | | 0.6%
/dev/sda2: |= / 1.2%
/dev/sda2: |= - 1.8%
/dev/sda2: |= \ 2.4%
[42949428.990000] usb 2-1: reset full speed USB device using ohci_hcd and
address 2
[42949434.670000] usb 2-1: device descriptor read/64, error -32
[42949434.920000] usb 2-1: device descriptor read/64, error -32
[42949435.170000] usb 2-1: reset full speed USB device using ohci_hcd and
address 2
[42949435.320000] usb 2-1: device descriptor read/64, error -32
[42949435.570000] usb 2-1: device descriptor read/64, error -32
[42949435.820000] usb 2-1: reset full speed USB device using ohci_hcd and
address 2
[42949436.250000] usb 2-1: device not accepting address 2, error -32
[42949436.390000] usb 2-1: reset full speed USB device using ohci_hcd and
address 2
[42949436.810000] usb 2-1: device not accepting address 2, error -32
[42949436.810000] sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
[42949436.820000] end_request: I/O error, dev sda, sector 1548079
[42949436.830000] Buffer I/O error on device sda2, logical block 131258
[42949436.830000] Buffer I/O error on device sda2, logical block 131259
[42949436.840000] Buffer I/O error on device sda2, logical block 131260
[42949436.850000] Buffer I/O error on device sda2, logical block 131261
[42949436.850000] Buffer I/O error on device sda2, logical block 131262
[42949436.860000] Buffer I/O error on device sda2, logical block 131263
[42949436.870000] Buffer I/O error on device sda2, logical block 131264
[42949436.870000] Buffer I/O error on device sda2, logical block 131265
[42949436.880000] Buffer I/O error on device sda2, logical block 131266
[42949436.880000] Buffer I/O error on device sda2, logical block 131267
[42949436.890000] usb 2-1: USB disconnect, address 2
[42949436.910000] sd 0:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
[42949436.910000] end_request: I/O error, dev sda, sector 1548319
[42949436.920000] sd 0:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
[42949436.930000] end_request: I/O error, dev sda, sector 1548335
Error reading block 131258 (Attempt to read block from filesystem resulted
in short read) while getting next inode from scan. Ignore error? yes
Force rewrite? yes
Error reading block 131259 (Attempt to read block from filesystem resulted
in short read) while getting next inode from scan. Ignore error? yes
After a ton of similar output I get this:
Error reading block 426145 (Atte[42949509.200000] EXT3-fs error (device
sda2): ext3_find_entry: mpt to refsck died with exit status 8
failed (code 8).
An autoreading directory #65281 offset 0matic file system check (fsck) of
the root filesystem failed. A
manual fsck must be performed, then the system restarted. The fsck should be
performed in maintenance mode with the root filesystem mounted in read-only
mode./l[42949509.230000] EXT3-fs error (device sda2): ext3_find_entry:
ib/lsb/init-functions: line 324: /bin/echo: No such file or direreading
directory #65286 offset 0ctory
The root filesystem is currently mounted in read-only mod
e. A maintenance shell will now be started. After performing
sys[42949509.250000] EXT3-fs error (device sda2): ext3_find_entry: tem
maintenance, press CONTROL-D to terminate the maintenance shreading
directory #89761 offset 0ell and restart the system./lib/lsb/init-functions:
line 322: /b
in/echo: No such file or directory
/etc/rcS.d/S10checkroot.sh: [42949509.280000] EXT3-fs error (device sda2):
ext3_find_entry: line 312: sulogin: command not found
Attempt to start maintenanreading directory #489601 offset 0ce shell failed.
Will restart in 5 seconds./lib/lsb/init-functio
ns: line 324: /bin/echo: No such file or directory
/etc/rcS.d/S10checkroot.sh: line 316: /bin/sleep: No such file or directory
/etc/rcS.d/S10checkroot.sh: line 319: reboot: command not
found[42949509.320000] EXT3-fs error (device sda2): ext3_find_entry:
reading directory #489601 offset 0
I have tried fsck on the usbstick on another computer without errors.
I start to belive that there is some hardware problem with my nslu :(
--
View this message in context: http://www.nabble.com/NSLU2-Lenny-install-problem-tp22608464p22916408.html
Sent from the debian-arm mailing list archive at Nabble.com.
Reply to: