hung DS10 - WAS: Please test new kernel-image-2.6.10-alpha packages
On Sun, 23 Jan 2005, Norbert Tretkowski wrote:
> With the latest upload of kernel-source-2.6.10 I was finally able to
> create working (for me) kernel-image-2.6.10-alpha packages. Please
> test them, especially when you're using a Qlogic ISP1020/1040 SCSI
> controller, which is now supported by the qla1280 driver. You also
> need to update initrd-tools if you want to use the qla1280 driver with
> your ISP1020/1040 controller.
I installed the generic kernel and the initrd-tools, but upon reboot my
DS10 hangs. This system contains two scsi cards, an NCR 53C895 and a
Qlogic 1020 (DEC originals, I don't remember the part numbers). Here
are details of the devices attached to the scsi cards, from 'show config':
Bus 00 Slot 14: NCR 53C895
pka0.7.0.14.0 SCSI Bus ID 7
dka100.1.0.14.0 COMPAQ BB018122B7
dka200.2.0.14.0 COMPAQ BB01813467
dka300.3.0.14.0 RZ1DF-CB
dka400.4.0.14.0 RZ1DB-CA
dka500.5.0.14.0 RZ1DB-CA
dka600.6.0.14.0 RZ1CB-CS
Bus 00 Slot 15: QLogic ISP10x0
pkb0.7.0.15.0 SCSI Bus ID 7
dkb0.0.0.15.0 COMPAQ BD036659CC
I was running kernel 2.6.8-1 (generic) without problem.
Here is the console log up to the hang:
>>>b dka500 -fl 0
(boot dka500.5.0.14.0 -flags 0)
block 0 of dka500.5.0.14.0 is a valid boot block
reading 171 blocks from dka500.5.0.14.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 15600(87552)
initializing HWRPB at 2000
initializing page table at 3ff30000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
aboot: Linux/Alpha SRM bootloader version 0.9b
aboot: switching to OSF/1 PALcode version 1.90
aboot: booting from device 'SCSI 0 14 0 5 500 0 0'
aboot: valid disklabel found: 8 partitions.
aboot: loading uncompressed vmlinuz...
aboot: loading compressed vmlinuz...
aboot: zero-filling 234628 bytes at 0xfffffc0000624524
aboot: loading initrd (6414336 bytes/6264 blocks) at 0xfffffc003f80a000
aboot: starting kernel vmlinuz with arguments ro root=/dev/sde5 console=ttyS0
Linux version 2.6.10-1-generic (tretkowski@bastille) (gcc version 3.3.5 (Debian 1:3.3.5-6)) #1 Wed Jan 26 19:44:07 UTC 2005
Booting GENERIC on Tsunami variation Webbrick using machine vector Webbrick from SRM
Major Options: LEGACY_START MAGIC_SYSRQ
Command line: ro root=/dev/sde5 console=ttyS0
memcluster 0, usage 1, start 0, end 256
memcluster 1, usage 0, start 256, end 130967
memcluster 2, usage 1, start 130967, end 131072
freeing pages 256:384
freeing pages 817:130967
reserving pages 817:819
Initial ramdisk at: 0xfffffc003f80a000 (6414336 bytes)
2048K Bcache detected; load hit latency 20 cycles, load miss latency 90 cycles
Built 1 zonelists
Kernel command line: ro root=/dev/sde5 console=ttyS0
PID hash table entries: 4096 (order: 12, 131072 bytes)
HWRPB cycle frequency bogus. Estimated 462428619 Hz
Using epoch = 1952
Console: colour dummy device 80x25
Dentry cache hash table entries: 262144 (order: 8, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 7, 1048576 bytes)
Memory: 1024128k/1047736k available (1886k kernel code, 21176k reserved, 536k data, 312k init)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512 (order: 0, 8192 bytes)
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 6264k freed
NET: Registered protocol family 16
EISA bus registered
pci: enabling save/restore of SRM state
Linux Plug and Play Support v0.97 (c) Adam Belay
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 8192 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 36 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
mice: PS/2 mouse device common for all mice
atkbd.c: keyboard reset failed on isa0060/serio1
atkbd.c: keyboard reset failed on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 6264KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 312k freed
initrd-tools: 0.1.76.1
NET: Registered protocol family 1
SCSI subsystem initialized
sym0: <895> rev 0x2 at pci 0000:00:0e.0 irq 35
sym0: Symbios NVRAM, ID 7, Fast-40, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: SCSI BUS has been reset.
sym0: SCSI BUS mode change from SE to SE.
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18m
elevator: using anticipatory as default io scheduler
Vendor: COMPAQ Model: BB018122B7 Rev: B016
Type: Direct-Access ANSI SCSI revision: 02
sym0:1:0: tagged command queuing enabled, command queue depth 16.
target0:0:1: Beginning Domain Validation
sym0:1: wide asynchronous.
sym0:1: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31)
target0:0:1: Domain Validation skipping write tests
target0:0:1: Ending Domain Validation
Vendor: COMPAQ Model: BB01813467 Rev: 3B07
Type: Direct-Access ANSI SCSI revision: 02
sym0:2:0: tagged command queuing enabled, command queue depth 16.
target0:0:2: Beginning Domain Validation
sym0:2: wide asynchronous.
sym0:2: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31)
target0:0:2: Domain Validation skipping write tests
target0:0:2: Ending Domain Validation
Vendor: DEC Model: RZ1DF-CB (C) DEC Rev: 0371
Type: Direct-Access ANSI SCSI revision: 02
sym0:3:0: tagged command queuing enabled, command queue depth 16.
target0:0:3: Beginning Domain Validation
sym0:3: wide asynchronous.
sym0:3: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 15)
target0:0:3: Domain Validation skipping write tests
target0:0:3: Ending Domain Validation
Vendor: DEC Model: RZ1DB-CA (C) DEC Rev: LYJ0
Type: Direct-Access ANSI SCSI revision: 02
sym0:4:0: tagged command queuing enabled, command queue depth 16.
target0:0:4: Beginning Domain Validation
sym0:4: wide asynchronous.
sym0:4: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31)
target0:0:4: Domain Validation skipping write tests
target0:0:4: Ending Domain Validation
Vendor: DEC Model: RZ1DB-CA (C) DEC Rev: LYJ0
Type: Direct-Access ANSI SCSI revision: 02
sym0:5:0: tagged command queuing enabled, command queue depth 16.
target0:0:5: Beginning Domain Validation
sym0:5: wide asynchronous.
sym0:5: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31)
target0:0:5: Domain Validation skipping write tests
target0:0:5: Ending Domain Validation
Vendor: DEC Model: RZ1CB-CS (C) DEC Rev: 0844
Type: Direct-Access ANSI SCSI revision: 02
sym0:6:0: tagged command queuing enabled, command queue depth 16.
target0:0:6: Beginning Domain Validation
sym0:6: wide asynchronous.
sym0:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 15)
target0:0:6: Domain Validation skipping write tests
target0:0:6: Ending Domain Validation
qla1280: QLA1040 found on PCI bus 0, dev 15
scsi(1:0): Resetting SCSI BUS
scsi1 : QLogic QLA1040 PCI to SCSI Host Adapter
Firmware version: 7.65.00, Driver version 3.25
Vendor: COMPAQ Model: BD036659CC Rev: 3B00
Type: Direct-Access ANSI SCSI revision: 03
scsi(1:0:0:0): Sync: period 10, offset 12, Wide, Tagged queuing: depth 255
ERROR: SCSI host `isp1020' has no error handling
ERROR: This is not a safe way to run your SCSI host
ERROR: The error handling must be added to this driver
fffffc00015d7df8 0000000000000000 fffffffc0038c500 fffffffc0035e920
fffffffc0035e920 fffffc003fe0c000 fffffffc0035e920 fffffc003fe0c000
fffffc0000000000 fffffc00015d7e40 fffffc00015d7e40 fffffc003fe0c000
fffffc00005a4500 fffffc003fe0c000 fffffffc0035208c fffffffc0035e920
fffffc00005a4500 fffffffc0035e920 fffffffc002ec04c fffffffc0035e920
fffffc00005a4500 fffffffc0035e9f0 fffffc00005a4500 fffffc00005a48e8
Trace:
[<fffffc000034e0c4>] sys_init_module+0x284/0x3e0
[<fffffc0000310b34>] entSys+0xa4/0xc0
qlogicisp : new isp1020 revision ID (5)
scsi2 : QLogic ISP1020 SCSI on PCI bus 00 device 78 irq 39 I/O base 0x8400
-------------------------------------------------------------------
Toni Harbaugh-Blackford harbaugh@abcc.ncifcrf.gov
System Administrator
Advanced Biomedical Computing Center (ABCC)
National Cancer Institute
Contractor - SAIC/Frederick
Reply to: