Re: any 2.6.x kernel for a DS10 with NCR 53C895 and QLogic ISP10x0 ?

[Jim Crilly <jim@why.dont.jablowme.net>]

I did an install last night on a 600Mhz Miata from a d-i nightly build 
and to my delight everything worked fine. Although I got the same OOPs 
when trying to boot 2.6.8-1-generic, strangely it continued to boot just 
fine. Since mine has some of the addresses decoded I assume I got a 
newer revision, even though the version was still 2.6.8-1-generic.

Jim.

Linux version 2.6.8-1-generic (tretkowski@raindrop) (gcc version 3.3.4 
(Debian 1:3.3.4-7)) #1 Tue Aug 17 08:46:31 CEST 2004
<snip>
qlogicisp : new isp1020 revision ID (5)
scsi0 : QLogic ISP1020 SCSI on PCI bus 01 device 20 irq 27 I/O base 0x8000
Using anticipatory io scheduler
scsi1 : QLogic ISP1020 SCSI on PCI bus 01 device 48 irq 40 I/O base 0x8400
  Vendor: SEAGATE   Model: ST34573N          Rev: 5958
  Type:   Direct-Access                      ANSI SCSI revision: 02
  Vendor: SEAGATE   Model: ST19171N          Rev: 0024
  Type:   Direct-Access                      ANSI SCSI revision: 02
SCSI device sda: 8888924 512-byte hdwr sectors (4551 MB)
SCSI device sda: drive cache: write back
 /dev/scsi/host1/bus0/target0/lun0: p1 p2 p3 p4 p5
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sdb: 17783112 512-byte hdwr sectors (9105 MB)
SCSI device sdb: drive cache: write through
 /dev/scsi/host1/bus0/target2/lun0: p1 p2 p3 p4
Attached scsi disk sdb at scsi1, channel 0, id 2, lun 0
Kernel bug at mm/slab.c:1544
modprobe(206): Kernel Bug 1
pc = [kmem_cache_destroy+64/496]  ra = [<fffffffc00241040>]  ps = 0000 
  Not tainted
v0 = 0000000000000000  t0 = 0000000000000000  t1 = fffffc001fff8840
t2 = fffffc000057b138  t3 = fffffc001f99d330  t4 = fffffc0000609bb8
t5 = 0000000000000400  t6 = fffffc0000c3a000  t7 = fffffc001f298000
a0 = 0000000000000000  a1 = fffffffc0024bb79  a2 = ffffffffbaadf00d
a3 = 00000000000000d0  a4 = fffffc001f29be28  a5 = fffffc001f99d228
t8 = 0000000000000000  t9 = fffffc000035745c  t10= 0000000000000030
t11= 0000000000000040  pv = fffffc0000357934  at = 0000000000000000
gp = fffffc00005f9b00  sp = fffffc001f29be88
Trace:
[sys_init_module+496/932] sys_init_module+0x1f0/0x3a4
[entSys+164/192] entSys+0xa4/0xc0

Code: a0480068  243f1000  2021ff00  44410002  e4400004  00000081 
<00000608> 004d6128
SGI XFS with ACLs, security attributes, realtime, large block/inode 
numbers, no debug enabled
SGI XFS Quota Management subsystem
VFS: Can't find ext2 filesystem on dev sda3.
XFS mounting filesystem sda3
Ending clean XFS mount for filesystem: sda3


Norbert Tretkowski wrote:
> * Toni L. Harbaugh-Blackford [Contr] wrote:
>
> > I just installed sarge on this box using the alpha rc1 netinst
> > image. But I had to use the 2.4.26-1-generic kernel because the
> > 2.6.6-1-generic failed on the reboot.
>
>
> There are kernel-images for 2.6.8 in testing, please try these, this
> sounds like a known bug.
>
> Norbert