XFREE86 on TGA
Hi all-
I'm trying to get xfree86 to run on my UDB. When I run startx I get a
screen and mouse that is much larger than it should be and then it dies
after a couple of seconds. Any thoughts?
Here are my specs:
Monitor: ViewSonic 17ea 1765ea-1 Video Sync: horiz 30-69kHz vert 50-120Hz
video card:The standard UDB card which I believe is a DEC TGA 21030 with 2
meg ram.
I'm pretty sure I just have something set wrong because I had this setup
working under a prior Redhat installation. When I run xf86config I'm using
my own numbers for the monitor setup (not any of the predefined ones) and
I'm choosing the accelerated video card option (otherwise it runs the SVGA
server instead of the TGA server, I think???) BTW shouldn't the xf86setup
program be included in the xfree86 .deb package? I didn't see it.
Here are the results of running startx:
XFree86 Version 3.3.2 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: March 2 1998
If the server is older than 6-12 months, or if your card is newer
than the above date, look for a newer version before reporting
problems. (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.1.106 alpha [ELF]
Configured drivers:
DEC_TGA: non-accelerated server for DEC 21030 TGA graphics adapters
(Patchlevel 0)
(using VT number 7)
XF86Config: /etc/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: keymap: "xfree86(us)" (overrides other XKB settings)
(**) Mouse: type: PS/2, device: /dev/mouse, buttons: 3
(**) Mouse: 3 button emulation (timeout: 50ms)
(**) DEC_TGA: Graphics device ID: "DEC TGA"
(**) DEC_TGA: Monitor ID: "ViewSonic 17ea"
(--) DEC_TGA: Mode "1024x768" needs hsync freq of 70.24 kHz. Deleted.
(--) DEC_TGA: Mode "1152x864" needs hsync freq of 70.88 kHz. Deleted.
(--) DEC_TGA: Mode "1280x1024" needs hsync freq of 74.59 kHz. Deleted.
(--) DEC_TGA: Mode "1600x1200" needs hsync freq of 75.00 kHz. Deleted.
(--) DEC_TGA: Mode "1152x864" needs hsync freq of 76.01 kHz. Deleted.
(--) DEC_TGA: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted.
(--) DEC_TGA: Mode "1024x768" needs hsync freq of 80.21 kHz. Deleted.
(--) DEC_TGA: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted.
(--) DEC_TGA: Mode "1600x1200" needs hsync freq of 87.50 kHz. Deleted.
(--) DEC_TGA: Mode "1152x864" needs hsync freq of 89.62 kHz. Deleted.
(--) DEC_TGA: Mode "1280x1024" needs hsync freq of 91.15 kHz. Deleted.
(--) DEC_TGA: Mode "1600x1200" needs hsync freq of 93.75 kHz. Deleted.
(--) DEC_TGA: Mode "1600x1200" needs hsync freq of 105.77 kHz. Deleted.
(--) DEC_TGA: Mode "1280x1024" needs hsync freq of 107.16 kHz. Deleted.
(--) DEC_TGA: Mode "1800X1440" needs hsync freq of 96.15 kHz. Deleted.
(--) DEC_TGA: Mode "1800X1440" needs hsync freq of 104.52 kHz. Deleted.
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/"
(--) DEC_TGA: DEC 21030 TGA 8 Plane Chip Found.
(--) DEC_TGA: videoram : 2048k
(--) DEC_TGA: Using ICS1562 programmable clock
(**) DEC_TGA: Option "dac_8_bit"
(--) DEC_TGA: Maximum allowed dot-clock: 135.000 MHz
(**) DEC_TGA: Cannot support interlaced modes, deleting.
(**) DEC_TGA: Cannot support interlaced modes, deleting.
(**) DEC_TGA: Cannot support interlaced modes, deleting.
(**) DEC_TGA: Mode "640x480": mode clock = 45.800
(--) DEC_TGA: TGA chipset currently only supports one modeline.
System: `/usr/X11R6/lib/X11/xkb/xkbcomp -w 1 -R/usr/X11R6/lib/X11/xkb -xkm
-m us -em1 "The XKEYBOARD keymap compiler (xkbcomp) reports:" -emp "> "
-eml "Errors from xkbcomp are not fatal to the X server" keymap/xfree86
compiled/xfree86.xkm'
waiting for X server to shut down
It seems to be passing the higher resolution modes. Could it be that my
hsync and vsync are set wrong?
Thanks in advance for your help,
Brett
--
To UNSUBSCRIBE, email to debian-alpha-request@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Reply to: