Was Samsung DVD writer.
Hi at all,
Excused if I have left to pass much time before answering.
I carried out the following test:
1.I update the firmare. No change.
2 I test the cdrtools-2.01.01a25.tar.gz and this is the result:
su-2.05b# cdrecord -scanbus
Cdrecord-ProDVD-Clone 2.01.01a25 (i386-unknown-freebsd6.1) Copyright (C) 1995-2006 Jörg Schilling
Using libscg version 'schily-0.9'.
scsibus1:
1,0,0 100) 'ATAPI ' 'CD-ROM 52X ' '172A' Removable CD-ROM
1,1,0 101) 'HL-DT-ST' 'CD-RW GCE-8481B ' '1.00' Removable CD-ROM
1,2,0 102) *
1,3,0 103) *
1,4,0 104) *
1,5,0 105) *
1,6,0 106) *
1,7,0 107) *
scsibus2:
2,0,0 200) 'TSSTcorp' 'CD/DVDW SH-S182M' 'SB04' Removable CD-ROM
2,1,0 201) *
2,2,0 202) *
2,3,0 203) *
2,4,0 204) *
2,5,0 205) *
2,6,0 206) *
2,7,0 207) *
su-2.05b# cdrecord dev=2,0,0 blank=all
Cdrecord-ProDVD-Clone 2.01.01a25 (i386-unknown-freebsd6.1) Copyright (C) 1995-2006 Jörg Schilling
scsidev: '2,0,0'
scsibus: 2 target: 0 lun: 0
Using libscg version 'schily-0.9'.
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'TSSTcorp'
Identifikation : 'CD/DVDW SH-S182M'
Revision : 'SB04'
Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM.
cdrecord: Input/output error. get performance: scsi sendcmd: retryable error
CDB: AC 00 00 00 00 00 00 00 00 64 03 00
status: 0x0 (GOOD STATUS)
cmd finished after 0.000s timeout 40s
Using generic SCSI-3/mmc-2 DVD-R/DVD-RW/DVD-RAM driver (mmc_dvd).
Driver flags : DVD MMC-3 SWABAUDIO BURNFREE
Supported modes: PACKET SAO
resid: 8
WARNING: Phys disk size 2295104 differs from rzone size 0! Prerecorded disk?
WARNING: Phys start: 196608 Phys end 2491711
cdrecord: Input/output error. get performance: scsi sendcmd: retryable error
CDB: AC 00 00 00 00 00 00 00 00 64 03 00
status: 0x0 (GOOD STATUS)
cmd finished after 0.000s timeout 100s
cdrecord: MMC-3 speed select did not work.
Starting to write CD/DVD at speed 4 in real BLANK mode for single session.
Last chance to quit, starting real write 0 seconds. Operation starts.
cdrecord: Input/output error. blank unit: scsi sendcmd: retryable error
CDB: A1 00 00 00 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 30 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x30 Qual 0x05 (cannot write medium - incompatible format) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.001s timeout 9600s
cdrecord: Cannot blank disk, aborting.
Other idea?
Thanks.
--
Isaia Luciano
FreeBSD user
Reply to: