networking restarts after resume
I use Etch, and I hibernate my computer with userspace suspend (uswsusp)
and hibernate packages. It generally works, but sometimes after the computer
resumed, networking restarts. ( and my X session, too). What is the problem?
Thanks.
dmesg:
[...]
Freezing cpus ...
Stopping tasks: ==============================================================
==============================================================================|
Shrinking memory... done (107919 pages freed)
pnp: Device 00:0c disabled.
pnp: Device 00:08 disabled.
pnp: Device 00:07 disabled.
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1f.4 disabled
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
....
swsusp: Need to copy 111050 pages
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
swsusp: Restoring Highmem
ACPI: Unable to turn cooling device [c18fbf04] 'on'
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:00:1f.2 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 11 (level, low)
-> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.2 to 64
PCI: Enabling device 0000:00:1f.4 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1f.4[C] -> Link [LNK1] -> GSI 9 (level, low)
-> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.4 to 64
PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was
2800005, writing 2800000)
PCI: Enabling device 0000:00:1f.5 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 7 (level, low)
-> IRQ 7
PCI: Setting latency timer of device 0000:00:1f.5 to 64
PM: Writing back config space on device 0000:02:01.0 at offset 1 (was
2100007, writing 2100000)
pnp: Device 00:07 activated.
pnp: Device 00:08 activated.
pnp: Failed to activate device 00:09.
pnp: Failed to activate device 00:0a.
pnp: Device 00:0c activated.
Restarting tasks... done
Thawing cpus ...
via-rhine.c:v1.10-LK1.4.1 July-24-2006 Written by Donald Becker
PCI: Enabling device 0000:02:01.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKC] -> GSI 11 (level, low)
-> IRQ 11
eth0: VIA Rhine II at 0x1c000, 00:e0:4c:99:08:13, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
logips2pp: Detected unknown logitech mouse model 0
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
input: ImPS/2 Logitech Wheel Mouse as /class/input/input9
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
bridge-eth0: enabling the bridge
bridge-eth0: up
eth0: no IPv6 routers present
[...]
Reply to: