Re: Motherbnoard Sound Device
On Tue, 13 Oct 1998, Bert Conliffe wrote:
Attached is my isapnp.conf file, so take a look at what I am using. Make
sure that you're settings are the board defaults, and not what Windows has
switched them too. Here's what I have for kernel options:
Sound card support = M
Sound Blaster (SB, SBPro, SB16, clones) support = Y
/dev/dsp and /dev/audio support = Y
FM synthesizer (YM3812/OPL-3) support = Y
I/O base for SG Check ... = 220
Sound Blaster IRQ ... = 5
Sound Blaster DMA 0,1,3 = 1
MPU401 I/O base SB16, Jazz16, ... = 330
SB MPU401 IRQ ... = 9
Audio DMA buffer size ... = 65536
All other options are no. The only problem I have encountered is that
sound doesn't play through the speakers with ASCD for some reason. I
haven't gotten around to fixing that yet. Good luck!
Rob
> Hi Robert Rati,
>
> Congradulations for your success! Now, if you'd be kind
> enought to share with the rest of us ( who are having similiar
> problems ), how it was done, we'd be most grateful.
>
> If not, your success is of no use to us, its a one man victory.
>
> Until I can get my sound device to speakto me under linux,
> with the setup I presently have; I'll stick with what the sages
> say, and look for relief elsewhere.
>
> Bert
>
>
>
>
>
>
>
>
>
>
>
>
>
> --
> Unsubscribe? mail -s unsubscribe debian-user-request@lists.debian.org < /dev/null
>
=======================================================================
ratirh@lore.cs.purdue.edu : Role-Player, Babylon 5 fanatic 1998-99
Aka Khyron the Backstabber : ICQ# 2325055
Homepage: www.cs.purdue.edu/homes/ratirh
"Happiness comes in short spurts. Don't be fooled."
=======================================================================
# $Id: pnpdump.c,v 1.1.1.2 1998/01/07 05:17:47 fred Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DNEEDNANOSLEEP
#
# Trying port address 0203
# Board 1 has serial identifier 8d 01 00 01 00 01 00 a9 0d
# Board 2 has serial identifier 00 1a 13 c8 05 00 14 49 0a
# (DEBUG)
(READPORT 0x0203)
(ISOLATE)
(IDENTIFY *)
# Card 1: (serial identifier 8d 01 00 01 00 01 00 a9 0d)
# Vendor Id CMI0001, Serial Number 16777472, checksum 0x8D.
# Version 1.0, Vendor version 0.0
# ANSI string -->CMI8330. Audio Adapter<--
#
# Logical device id @@@0001
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CMI0001/16777472 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0530
# Maximum IO base address 0x0530
# IO base alignment 1 bytes
# Number of IO addresses required: 8
#(IO 0 (BASE 0x0530))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 8
#(IO 1 (BASE 0x0388))
# IRQ 11.
# High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 11 (MODE +E)))
# First DMA channel 0.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
#(DMA 0 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0530
# Maximum IO base address 0x0530
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0530))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 1 (BASE 0x0388))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0e80
# Maximum IO base address 0x0f40
# IO base alignment 192 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0e80))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x03f8
# IO base alignment 16 bytes
# Number of IO addresses required: 8
# (IO 1 (BASE 0x0388))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# End dependent functions
#(ACT Y)
))
#
# Logical device id @H@0001
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CMI0001/16777472 (LD 1
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 1 bytes
# Number of IO addresses required: 2
(IO 0 (BASE 0x0330))
# IRQ 9.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 9 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 16 bytes
# Number of IO addresses required: 2
# (IO 0 (BASE 0x0300))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# End dependent functions
(ACT Y)
))
#
# Logical device id @P@0001
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CMI0001/16777472 (LD 2
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 1 bytes
# Number of IO addresses required: 8
#(IO 0 (BASE 0x0200))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0fe0
# IO base alignment 16 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0200))
# End dependent functions
#(ACT Y)
))
#
# Logical device id @X@0001
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CMI0001/16777472 (LD 3
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 1 bytes
# Number of IO addresses required: 16
(IO 0 (BASE 0x0220))
# IRQ 5.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 0 (CHANNEL 1))
# Next DMA channel 5.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
(DMA 1 (CHANNEL 5))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
#(IO 0 (BASE 0x0220))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
#(INT 0 (IRQ 7 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
#(DMA 0 (CHANNEL 1))
# Next DMA channel 5 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
#(DMA 1 (CHANNEL 5))
# End dependent functions
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Card 2: (serial identifier 00 1a 13 c8 05 00 14 49 0a)
# Vendor Id BRI1400, Serial Number 437504005, checksum 0x00.
# ANSI string -->Boca Research 33,600 ACF Modem <--
# Version 1.0, Vendor version 0.0
#
# Logical device id BRI1400
# Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE BRI1400/437504005 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03f8
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x03f8))
# IRQ 4.
# High true, level sensitive interrupt
# (INT 0 (IRQ 4 (MODE +L)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02f8
# Maximum IO base address 0x02f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
(IO 0 (BASE 0x02f8))
# IRQ 3.
# High true, level sensitive interrupt
(INT 0 (IRQ 3 (MODE +L)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03e8
# Maximum IO base address 0x03e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x03e8))
# IRQ 4.
# High true, level sensitive interrupt
# (INT 0 (IRQ 4 (MODE +L)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02e8
# Maximum IO base address 0x02e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x02e8))
# IRQ 3.
# High true, level sensitive interrupt
# (INT 0 (IRQ 3 (MODE +L)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03f8
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x03f8))
# IRQ 3, 5, 7, 9, 10, 11, 12 or 15.
# High true, level sensitive interrupt
# (INT 0 (IRQ 3 (MODE +L)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02f8
# Maximum IO base address 0x02f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x02f8))
# IRQ 4, 5, 7, 9, 10, 11, 12 or 15.
# High true, level sensitive interrupt
# (INT 0 (IRQ 4 (MODE +L)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03e8
# Maximum IO base address 0x03e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x03e8))
# IRQ 3, 5, 7, 9, 10, 11, 12 or 15.
# High true, level sensitive interrupt
# (INT 0 (IRQ 3 (MODE +L)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02e8
# Maximum IO base address 0x02e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x02e8))
# IRQ 4, 5, 7, 9, 10, 11, 12 or 15.
# High true, level sensitive interrupt
# (INT 0 (IRQ 4 (MODE +L)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0xfff8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0100))
# IRQ 3, 4, 5, 7, 9, 10, 11, 12 or 15.
# High true, level sensitive interrupt
# (INT 0 (IRQ 3 (MODE +L)))
# End dependent functions
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
Reply to: