Modem 3g - Claro - ZTE MF626
Hola amigos, tengo algun problema extraño al intentar
conectarme con un modem 3g ZTE MF626, de la operadora Claro de Paraguay.
He conseguido que me reconozca el modem:
ls /dev/ttyU*
/dev/ttyUSB0
Al darle dmesg veo:
[13529.798900] usb 5-2: USB disconnect, address 6
[13529.799055] generic ttyUSB0: generic converter now disconnected from ttyUSB0
[13529.799068] usbserial_generic 5-2:1.0: device disconnected
[13677.660014] usb 5-2: new high speed USB device using ehci_hcd and address 7
[13677.805063] usb 5-2: configuration #1 chosen from 1 choice
[13677.806557] usb-storage: device ignored
[13677.806648] usbserial_generic 5-2:1.0: generic converter detected
[13677.806700] usb 5-2: generic converter now attached to ttyUSB0
[13677.806802] usb 5-2: New USB device found, idVendor=19d2, idProduct=2000
[13677.806805] usb 5-2: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[13677.806807] usb 5-2: Product: ZTE CDMA Technologies MSM
[13677.806809] usb 5-2: Manufacturer: ZTE, Incorporated
Pero al darle: # wvdialconf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1 S2 S3
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Sorry, no modem was detected! Is it in use by another program?
Did you configure it properly with setserial?
Please read the FAQ at http://open.nit.ca/wiki/?WvDial
If you still have problems, send mail to <wvdial-list@lists.nit.ca>.
Y ahí ya no se que puedo hacer,
mire la ayuda de setserial y no entiendo que puedo configurar con ese
programa, y el FAQ de WvDial no lo puedo acceder porque aqui en mi
trabajo aparentemente lo tengo filtrado.
Luego de conseguir los datos de mi operadora local mi archivo de
configuracion del wvdial quedo así:
# cat /etc/wvdial.conf
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
ISDN = 0
Phone = *99#
New PPPD = yes
Modem = /dev/ttyUSB0
Username = ctigprs
Password = ctigprs999
Baud = 460800
Alguna idea, ayuda o algo para seguir mirando?
Desde ya muchas gracias y un abrazo para todos.
--
§~^Calabaza^~§ from Villa Elisa, Paraguay
Reply to: