WebCam Genius Express V2
Hola, estoy intentando hacer funcionar mi webcam, una Genius Express V2.
Utilizo Debian Sid con kernel 2.6.7 compilado por mí.
He buscado por google en muchas páginas para ver que soporte tenía que activar
en el kernel. Todos las entradas USB detectan si enchufo la camara, lo
compruebo haciendo "usbview", pero me pone "dispositivo desconocido", o sea,
que no tengo el driver adecuado, supongo.
Si hago "lsusb" me sale:
Bus 004 Device 010: ID 0458:7004 KYE Systems Corp. (Mouse Systems)
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Y si hago dmesg, lo referente a USB es lo siguiente:
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.3: reset hcs_params 0x3206 dbg=0 cc=3 pcc=2 ordered !ppc
ports=6
ehci_hcd 0000:00:10.3: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:00:10.3: capability 0001 at 68
ehci_hcd 0000:00:10.3: irq 10, pci mem d0b36000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: reset command 080002 (park)=0 ithresh=8 period=1024
Reset HALT
ehci_hcd 0000:00:10.3: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
ehci_hcd 0000:00:10.3: supports USB remote wakeup
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: VIA Technologies, Inc. USB 2.0
usb usb1: Manufacturer: Linux 2.6.7-ck6 ehci_hcd
usb usb1: SerialNumber: 0000:00:10.3
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:10.0: irq 10, io base 0000d400
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: detected 2 ports
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
usb usb2: Manufacturer: Linux 2.6.7-ck6 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:00:10.1: irq 11, io base 0000d800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: detected 2 ports
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: default language 0x0409
usb usb3: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#2)
usb usb3: Manufacturer: Linux 2.6.7-ck6 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#3)
uhci_hcd 0000:00:10.0: port 1 portsc 008a
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
uhci_hcd 0000:00:10.0: port 2 portsc 008a
hub 2-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
uhci_hcd 0000:00:10.2: irq 11, io base 0000dc00
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: detected 2 ports
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: default language 0x0409
usb usb4: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#3)
usb usb4: Manufacturer: Linux 2.6.7-ck6 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
uhci_hcd 0000:00:10.1: port 1 portsc 008a
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
uhci_hcd 0000:00:10.1: port 2 portsc 008a
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
mice: PS/2 mouse device common for all mice
input: PC Speaker
serio: i8042 AUX port at 0x60,0x64 irq 12
uhci_hcd 0000:00:10.0: port 1 portsc 0088
hub 2-0:1.0: port 1 enable change, status 00000100
uhci_hcd 0000:00:10.0: port 2 portsc 0088
hub 2-0:1.0: port 2 enable change, status 00000100
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
uhci_hcd 0000:00:10.2: port 1 portsc 008a
hub 4-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
uhci_hcd 0000:00:10.2: port 2 portsc 008a
hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
input: AT Translated Set 2 keyboard on isa0060/serio0
uhci_hcd 0000:00:10.1: port 1 portsc 0088
hub 3-0:1.0: port 1 enable change, status 00000100
uhci_hcd 0000:00:10.1: port 2 portsc 0088
hub 3-0:1.0: port 2 enable change, status 00000100
uhci_hcd 0000:00:10.2: port 1 portsc 0088
hub 4-0:1.0: port 1 enable change, status 00000100
uhci_hcd 0000:00:10.2: port 2 portsc 0088
hub 4-0:1.0: port 2 enable change, status 00000100
uhci_hcd 0000:00:10.0: suspend_hc
uhci_hcd 0000:00:10.1: suspend_hc
uhci_hcd 0000:00:10.2: suspend_hc
ehci_hcd 0000:00:10.3: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 6: delay 100ms stable 4 status 0x501
hub 1-0:1.0: port 6 not reset yet, waiting 50ms
ehci_hcd 0000:00:10.3: port 6 full speed --> companion
ehci_hcd 0000:00:10.3: GetStatus port 6 status 003801 POWER OWNER sig=j
CONNECT
uhci_hcd 0000:00:10.2: wakeup_hc
uhci_hcd 0000:00:10.2: port 2 portsc 0093
hub 4-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 4-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
usb 4-2: new full speed USB device using address 2
usb 4-2: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 4-2: hotplug
usb 4-2: adding 4-2:1.0 (config #1, interface 0)
usb 4-2:1.0: hotplug
uhci_hcd 0000:00:10.2: port 2 portsc 008a
hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
usb 4-2: USB disconnect, address 2
usb 4-2: usb_disable_device nuking all URBs
usb 4-2: unregistering interface 4-2:1.0
usb 4-2:1.0: hotplug
usb 4-2: unregistering device
usb 4-2: hotplug
ehci_hcd 0000:00:10.3: GetStatus port 6 status 001002 POWER sig=se0 CSC
hub 1-0:1.0: port 6, status 0100, change 0001, 12 Mb/s
uhci_hcd 0000:00:10.2: port 2 portsc 0088
hub 4-0:1.0: port 2 enable change, status 00000100
uhci_hcd 0000:00:10.2: suspend_hc
ehci_hcd 0000:00:10.3: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 6: delay 100ms stable 4 status 0x501
hub 1-0:1.0: port 6 not reset yet, waiting 50ms
ehci_hcd 0000:00:10.3: port 6 full speed --> companion
ehci_hcd 0000:00:10.3: GetStatus port 6 status 003801 POWER OWNER sig=j
CONNECT
uhci_hcd 0000:00:10.2: wakeup_hc
uhci_hcd 0000:00:10.2: port 2 portsc 0093
hub 4-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 4-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
usb 4-2: new full speed USB device using address 3
usb 4-2: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 4-2: hotplug
usb 4-2: adding 4-2:1.0 (config #1, interface 0)
usb 4-2:1.0: hotplug
ehci_hcd 0000:00:10.3: GetStatus port 6 status 001002 POWER sig=se0 CSC
hub 1-0:1.0: port 6, status 0100, change 0001, 12 Mb/s
uhci_hcd 0000:00:10.2: port 2 portsc 008a
hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
usb 4-2: USB disconnect, address 3
usb 4-2: usb_disable_device nuking all URBs
usb 4-2: unregistering interface 4-2:1.0
usb 4-2:1.0: hotplug
usb 4-2: unregistering device
usb 4-2: hotplug
uhci_hcd 0000:00:10.2: port 2 portsc 0088
hub 4-0:1.0: port 2 enable change, status 00000100
uhci_hcd 0000:00:10.2: suspend_hc
ehci_hcd 0000:00:10.3: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 6: delay 100ms stable 4 status 0x501
hub 1-0:1.0: port 6 not reset yet, waiting 50ms
ehci_hcd 0000:00:10.3: port 6 full speed --> companion
ehci_hcd 0000:00:10.3: GetStatus port 6 status 003801 POWER OWNER sig=j
CONNECT
uhci_hcd 0000:00:10.2: wakeup_hc
uhci_hcd 0000:00:10.2: port 2 portsc 0093
hub 4-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 4-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
usb 4-2: new full speed USB device using address 4
usb 4-2: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 4-2: hotplug
usb 4-2: adding 4-2:1.0 (config #1, interface 0)
usb 4-2:1.0: hotplug
Si hago "dmesg | grep video" o "dmesg | grep cam" no sale nada.
Doy por hecho que he activado más cosas de las necesarias en el kernel, pero
bueno.
Tengo instalado el paquete "v4l-conf".
El caso es que he ido a la página:
http://www.qbik.ch/usb/devices/showdev.php?id=1975
en la que se dan unos drivers para mi webcam, los spca50x. En estos drivers me
informan de que necesito "v4l stuff" en el kernel tanto para 2.4 como para
2.6, pero no encuentro dicha opción en mi kernel 2.6.7.
Entonces hago la instalación del driver supuestamente sin problemas.
También me indican que tras la instalación, al hacer "lsmod, spca50x should be
load with videodev", pero yo hago "lsmod" y no aparece nada al respecto.
En definitiva no logro que me detecte la camara.
¿Alguien sabe qué me falta? Muchas gracias.
Reply to: