scsi & usb
Bonjour,
J'ai installe etch, sur un PIII, avec carte scsi 29160 adaptec
( 3 DD de 9 Go en sus de 2 DD ide ), sur une carte mère msi 694T pro !
Quand je monte un DD en USB sa rame terrible, il tente d'utiliser la
carte scsi !
Comment remedier au Probleme de la lenteur ?
( faut charger un autre module ?, je souhaite éviter une compile noyeau )
Merci
Tous mes voeux .....
( plein de bonnes choses )
Ptilou
l'erreur dans le dmesg :
Initializing USB Mass Storage driver...
scsi1 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
sd 0:0:11:0: Attempting to queue an ABORT message
CDB: 0x12 0x1 0x0 0x0 0xfe 0x0
sd 0:0:11:0: Command already completed
aic7xxx_abort returns 0x2002
Vendor: HDS72808 Model: 0PLAT20 Rev: PF2O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdd: 160836479 512-byte hdwr sectors (82348 MB)
sdd: Write Protect is off
sdd: Mode Sense: 03 00 00 00
sdd: assuming drive cache: write through
SCSI device sdd: 160836479 512-byte hdwr sectors (82348 MB)
sdd: Write Protect is off
sdd: Mode Sense: 03 00 00 00
sdd: assuming drive cache: write through
sdd: sdd2
sd 1:0:0:0: Attached scsi disk sdd
usb-storage: device scan complete
sd 0:0:11:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
sd 0:0:11:0: Command already completed
aic7xxx_abort returns 0x2002
sd 0:0:10:0: Attempting to queue an ABORT message
CDB: 0x12 0x1 0x0 0x0 0xfe 0x0
sd 0:0:10:0: Command not found
aic7xxx_abort returns 0x2002
sd 0:0:10:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
sd 0:0:10:0: Command already completed
aic7xxx_abort returns 0x2002
sd 0:0:8:0: Attempting to queue an ABORT message
CDB: 0x12 0x1 0x0 0x0 0xfe 0x0
sd 0:0:8:0: Command not found
aic7xxx_abort returns 0x2002
sd 0:0:8:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
sd 0:0:8:0: Command already completed
aic7xxx_abort returns 0x2002
sd 0:0:8:0: Attempting to queue a TARGET RESET message
CDB: 0x12 0x1 0x0 0x0 0xfe 0x0
sd 0:0:8:0: Command not found
aic7xxx_dev_reset returns 0x2002
sd 0:0:8:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
sd 0:0:8:0: Command already completed
aic7xxx_abort returns 0x2002
sd 0:0:10:0: Attempting to queue a TARGET RESET message
CDB: 0x12 0x1 0x0 0x0 0xfe 0x0
sd 0:0:10:0: Command not found
aic7xxx_dev_reset returns 0x2002
sd 0:0:10:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
sd 0:0:10:0: Command already completed
aic7xxx_abort returns 0x2002
sd 0:0:11:0: Attempting to queue a TARGET RESET message
CDB: 0x12 0x1 0x0 0x0 0xfe 0x0
sd 0:0:11:0: Command not found
aic7xxx_dev_reset returns 0x2002
sd 0:0:11:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
sd 0:0:11:0: Command already completed
aic7xxx_abort returns 0x2002
sd 0:0:11:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
scsi0: At time of recovery, card was paused
Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi0: Dumping Card State in Message-out phase, at SEQADDR 0x16c
Card was paused
ACCUM = 0xa0, SINDEX = 0x61, DINDEX = 0xe4, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x1
SCSIPHASE[0x4]:(MSG_OUT_PHASE) SCSISIGI[0xb6]:(REQI|BSYI|ATNI|MSGI|CDI)
ERROR[0x0] SCSIBUSL[0xc0] LASTPHASE[0xa0]:(MSGI|CDI)
SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI) SBLKCTL[0xa]:(SELWIDE|SELBUSB)
SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE) SEQ_FLAGS[0x40]:(NO_CDB_SENT)
SSTAT0[0x2]:(SPIORDY) SSTAT1[0x1]:(REQINIT) SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x8]:(ENSWRAP) SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST
|ENSELTIMO)
SXFRCTL0[0x88]:(SPIOEN|DFON) DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_
AVAIL)
STACK: 0xe2 0x0 0x164 0x179
SCB count = 8
Kernel NEXTQSCB = 7
Card NEXTQSCB = 7
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 2 0 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 2
2 23 24 25 26 27 28 29 30 31
Sequencer SCB Info:
0 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0xa7]:(TWIN_CHNLB)
SCB_LUN[0x0] SCB_TAG[0xff]
1 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0xb7]:(TWIN_CHNLB)
SCB_LUN[0x0] SCB_TAG[0x2]
2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0xb7]:(TWIN_CHNLB)
SCB_LUN[0x0] SCB_TAG[0xff]
3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0xa7]:(TWIN_CHNLB)
SCB_LUN[0x0] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
--More--(51%)
Reply to: