[Debian] Problem mit XFree 4.0.2 und bttv
Hallo,
ich habe ein großes Problem: Mein TV will nicht funktionieren
(zumindest das Overlaying). Ich benutze kwintv 0.8.5 und xawtv 3.38
mit einem 2.2.18 Kernel mit reiserfs-Patch 3.5.31 und neuem
i2c-Stack. Die bttv-Version ist 0.7.59. Die Module sind alle
vorhanden und scheinen auch ordentlich geladen zu werden:
botanica:/home/rene# modprobe bttv
botanica:/home/rene# lsmod
Module Size Used by
tvaudio 9936 0 (autoclean) (unused)
bttv 55424 0 (unused)
tuner 4464 1 (autoclean)
msp3400 21984 1 (autoclean)
kcompat24 3808 0 [tvaudio bttv msp3400]
i2c-algo-bit 7664 1 [bttv]
i2c-core 12736 0 [tvaudio bttv tuner msp3400
i2c-algo-bit]
videodev 2816 2 [bttv]
adlib_card 1040 0 (autoclean)
opl3 14560 0 (autoclean) [adlib_card]
sb 36944 0 (autoclean)
uart401 6640 0 (autoclean) [sb]
sound 63744 0 (autoclean) [adlib_card opl3 sb
uart401]
soundlow 384 0 (autoclean) [sound]
soundcore 3536 6 (autoclean) [sb sound]
dmesg:
...
bttv: driver version 0.7.59 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 2) at 00:0a.0, irq: 9, latency: 32, memory:
0xeb000000
bttv0: subsystem: 0070:13eb => Hauppauge WinTV => card=10
bttv0: model: BT878(Hauppauge new (bt878)) [insmod option]
PCI: Enabling bus mastering for device 00:50
bttv0: Hauppauge msp34xx: reset line init
msp34xx: init: chip=MSP3410D-B4, has NICAM support
msp3410: daemon started
bttv0: i2c attach [MSP3410D-B4]
i2c-core.o: client [MSP3410D-B4] registered to adapter [bt848
#0](pos. 0).
tuner: chip found @ 0x61
bttv0: i2c attach [Philips PAL]
i2c-core.o: client [Philips PAL] registered to adapter [bt848
#0](pos. 1).
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: Hauppauge eeprom: model=61314, tuner=Philips FI1216 MK2 (5),
radio=no
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips:
tda9840,tda9873h,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54
(PV951)
i2c-core.o: driver generic i2c audio driver registered.
Weiterhin sieht meine XF86Config folgendermassen aus:
Section "Module"
Load "dbe" # Double buffer extension
# SubSection "extmod"
# Option "omit xfree86-dga" # don't initialise the DGA #
#extension
# EndSubSection
Load "extmod"
Load "type1"
Load "freetype"
Load "speedo"
Load "glx"
Load "dri"
Load "dga"
Load "v4l"
EndSection
Es sollte also dga vorhanden sein. Auch die Base-Adresse wurde beim
Laden des Moduls richtig erkannt. xawtv bemerkt aber trotzdem diese
beiden Dinge:
rene@botanica:~$ xawtv
This is xawtv-3.38, running on Linux/i586 (2.2.18)
image format list for port 42
0x32315659 (YV12) planar
0x30323449 (I420) planar
Xv: no usable image format found (port 42)
x11: 1280x1024, 32 bit/pixel, 0 byte/scanline
WARNING: Your X-Server has no DGA support.
WARNING: couldn't find framebuffer base address, try manual
configuration ("v4l-conf -a <addr>")
v4l: 1280x1024, 32 bit/pixel, 5120 byte/scanline
wmhooks: netwm
no infrared remote support available
ioctl: VIDIOCCAPTURE(on): Invalid argument
ioctl: VIDIOCCAPTURE(off): Invalid argument
Und kwintv bringt nur eine Menge solcher Fehlermeldungen:
rene@botanica:~$ kwintv
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: VIDIOCCAPTURE in ::setCapture
Warning: v4l1: ioctl VIDIOCCAPTURE in v4l1if::~v4l1if
Ich weiss ehrlich gesagt nicht, wo ich noch suchen soll. Ich poste
deshalb in die Mailingliste, weil ich die vage Ahnung habe, dass das
verwendete XFree-Packet vielleicht ohne DGA compiled wurde.
Ich bin für jede Hilfe dankbar, bastle jetzt schon eine Woche an
diesem Problem.
Tschüß, Rene.
PS: Ich verwende das xawtv als debian-Package in der genannten
Version und XFree in Version 4.0.2-7 ebenfalls als Package. KWintv
mußte ich selbst compilen.
--
René Meyer
Student of Physics - Chemnitz University of Technology
http://www.tu-chemnitz.de/~meyr/
talk:rene@botanica.csn.tu-chemnitz.de
--
-----------------------------------------------------------
Um sich aus der Liste auszutragen schicken Sie bitte eine
E-Mail an debian-user-de-request@lehmanns.de die im Subject
"unsubscribe <deine_email_adresse>" enthaelt.
Bei Problemen bitte eine Mail an: Jan.Otto@Lehmanns.de
-----------------------------------------------------------
681 eingetragene Mitglieder in dieser Liste.
Reply to: