sun ultra10 usb problem
well
I'm thinking using usb mass storage on my
ultra10 with woody 30r2
I added a pci card with usb ports
but
I'have some usb trouble
so dmesg give:
hub.c: Cannot enable port 1 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
sunmouse: Successfully adjusted to 1200 baud.
hub.c: Cannot enable port 1 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
hub.c: Cannot enable port 1 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
hub.c: Cannot enable port 1 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
usb.c: deregistering driver usb-storage
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
hub.c: Cannot enable port 1 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
VFS: Disk change detected on device ide1(22,0)
ISO 9660 Extensions: RRIP_1991A
usb.c: USB disconnect on device 1
usb.c: USB bus 1 deregistered
usb.c: USB disconnect on device 1
hub.c: get_port_status(1) failed (err = -19)
hub.c: get_port_status(1) failed (err = -19)
hub.c: get_port_status(1) failed (err = -19)
hub.c: get_port_status(1) failed (err = -19)
hub.c: Cannot enable port 1 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
hub.c: cannot disable port 1 of hub 1 (err = -19)
hub.c: get_port_status failed (err = -19)
hub.c: get_hub_status failed
usb.c: USB bus 2 deregistered
usb.c: deregistering driver usb-storage
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
VFS: Disk change detected on device ide1(22,0)
ISO 9660 Extensions: RRIP_1991A
usb.c: deregistering driver usb-storage
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
Red Hat/Adaptec aacraid driver, Apr 11 2002
BlueZ HCI Core ver 1.1 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
BlueZ HCI USB driver ver 1.0 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
usb.c: registered new driver hci_usb
uhci.c: USB Universal Host Controller Interface driver v1.1
uhci.c: USB UHCI at I/O 0x2000400, IRQ 10,7d0
usb.c: new USB bus registered, assigned bus number 1
uhci.c: port count misdetected? forcing to 2 ports
uhci: USBCMD_HCRESET timed out!
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB UHCI at I/O 0x2000420, IRQ 10,7d1
usb.c: new USB bus registered, assigned bus number 2
uhci.c: port count misdetected? forcing to 2 ports
uhci: USBCMD_HCRESET timed out!
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: $Revision: 1.275 $ time 15:02:34 Apr 11 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver usb_mouse
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usb.c: registered new driver usbnet
hub.c: Cannot enable port 1 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
VFS: Disk change detected on device fd(2,0)
hub.c: Cannot enable port 1 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
hub.c: Cannot enable port 1 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
hub.c: Cannot enable port 1 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
and my usb cable is working well
and cat /proc/scsi/scsi give none attached
so what should I do ?
--
philippe.mortier@nordnet.fr
Reply to: