Re: Help please to debug failure to boot from disk on ss20 running woody
hmm, good advice I guess, but I can't reply to you directly....
----
The original message was received at Sat, 2 Feb 2002 09:51:53 +0100 (CET)
from mail@h59n3fls22o974.telia.com [213.64.105.59]
----- The following addresses had permanent fatal errors -----
<david@mailb.telia.com>
----
I wanted to reply to you that I tried your suggestion, bot with :d and
:a, and that this was my setup:
df -H
Filesystem Size Used Avail Use% Mounted on
/dev/sda4 753M 674M 41M 95% /
/dev/sda1 20M 4.9M 14M 26% /boot
/dev/sdb1 1.0G 435M 547M 45% /usr
/dev/sdc1 722M 150M 535M 22% /var
/dev/sdc2 671M 59M 578M 10% /home
/dev/sdd1 1.0G 326M 653M 34% /share1
/dev/sdd2 1.0G 21k 977M 1% /share2
that is I have my boot image in /dev/sda1 and my root in /dev/sda4.
I also want to tell you that I have two scsi controllers:
esp0: IRQ 36 SCSI ID 7 Clk 40MHz CCF=8 TOut 167 NCR53C9XF(espfast)
esp1: IRQ 53 SCSI ID 7 Clk 40MHz CCF=8 TOut 167 NCR53C9XF(espfast)
scsi0 : Sparc ESP100A-FAST
scsi1 : Sparc ESP236-FAST
scsi : 2 hosts.
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 1, lun 0
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 3, lun 0
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdc at scsi1, channel 0, id 1, lun 0
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdd at scsi1, channel 0, id 2, lun 0
scsi : detected 1 SCSI cdrom 4 SCSI disks total.
esp0: target 1 [period 100ns offset 15 10.00MHz FAST SCSI-II]
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2061108 [1006 MB] [1.0 GB]
esp0: target 3 [period 100ns offset 15 10.00MHz FAST SCSI-II]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 2061108 [1006 MB] [1.0 GB]
esp1: target 1 [period 200ns offset 15 5.00MHz synchronous SCSI]
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 2767245 [1351 MB] [1.4 GB]
esp1: target 2 [period 100ns offset 15 10.00MHz FAST SCSI-II]
SCSI device sdd: hdwr sector= 512 bytes. Sectors= 4096656 [2000 MB] [2.0 GB]
(this was with booting from the install image 2.2.19-sun4cdm)
Any more help is greatly appreciated.
TIA,
/ChJ
On Sat, Feb 02, 2002 at 09:35:10AM +0100, Christian Jönsson wrote:
>
>
> -----Ursprungligt meddelande-----
> Från: david@mailb.telia.com [mailto:david@mailb.telia.com]För david howe
> Skickat: den 2 februari 2002 08:13
> Till: Christian Jönsson
> Ämne: Re: Help please to debug failure to boot from disk on ss20 running
> woody
>
>
> Christian Jönsson wrote:
> >
> > I have a SPARCserver 20 that I run an up to date woody on.
> >
> > When I try booting from disk I instantly get an
> > Illegal Instruction.
> >
> > <#0> ok boot disk
> > Boot device_ /iommu/sbus/espdma@f,400000/esp@f,800000/sd@3,0 File and
> > args: (then I can't see more on my serial port access)
> > Illegal Instruction
>
> Can u boot with a command like
> #0 ok boot /iommu/sbus/espdma/esp/sd@3,0:d
>
> david
>
Reply to: