[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#886746: marked as done (linux-image-4.9.0-5-amd64: screen connected via displayport hub flashes black)

Your message dated Sun, 2 May 2021 11:46:18 +0200
with message-id <YI506v0LoEJpDcId@eldamar.lan>
and subject line Re: Bug#886746: Bug is fixed in vanilla kernel 4.9.77
has caused the Debian Bug report #886746,
regarding linux-image-4.9.0-5-amd64: screen connected via displayport hub flashes black
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
886746: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=886746
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message --- 
Package: src:linux
Version: 4.9.65-3+deb9u2
Severity: normal

Dear Maintainer,

   * What led up to the situation?

Installed linux-image-4.9.0-5-amd64 version 4.9.65-3+deb9u2

   * What exactly did you do (or not do) that was effective (or
     ineffective)?

Open a gnome-terminal window, wait a while then type something

   * What was the outcome of this action?

Sometimes one of the two connected monitors will suddenly go black for a
few seconds.  (It's happened three or four times as I type this bug report).

   * What outcome did you expect instead?

That the monitor not go black.

This bug didn't happen with the previous version of the kernel,
linux-image-4.9.0-4-amd64

The system has intel graphics, one displayport connector.  Two monitors are
connected via a 3 port displayport hub.

No messages appear in the kernel log or journal when the screen goes black.
One FIFO underrun message is in the kernel log, but it's many minutes before
the screen flashing:

Jan  9 14:17:45 cymric kernel: [  140.418643] [drm:intel_set_cpu_fifo_underrun_reporting [i915]] *ERROR* uncleared fifo underrun on pipe A
Jan  9 14:17:45 cymric kernel: [  140.418655] [drm:ironlake_irq_handler [i915]] *ERROR* CPU pipe A FIFO underrun


-- Package-specific info:
** Version:
Linux version 4.9.0-5-amd64 (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 SMP Debian 4.9.65-3+deb9u2 (2018-01-04)

** Command line:
BOOT_IMAGE=/boot/vmlinuz-4.9.0-5-amd64 root=UUID=81e06bed-a8c7-4345-9e2c-9c70a0b8e6d6 ro quiet splash

** Not tainted

** Kernel log:
Unable to read kernel log; any relevant messages should be attached

** Model information
sys_vendor: Dell Inc.
product_name: OptiPlex 3020
product_version: 01
chassis_vendor: Dell Inc.
chassis_version: 
bios_vendor: Dell Inc.
bios_version: A03
board_vendor: Dell Inc.
board_name: 0WMJ54
board_version: A00

** Loaded modules:
fuse
cbc
cts
rpcsec_gss_krb5
nfsv4
dns_resolver
nfs
lockd
grace
fscache
intel_rapl
x86_pkg_temp_thermal
intel_powerclamp
coretemp
kvm_intel
snd_hda_codec_realtek
kvm
snd_hda_codec_generic
irqbypass
snd_hda_codec_hdmi
crct10dif_pclmul
snd_hda_intel
snd_hda_codec
crc32_pclmul
ghash_clmulni_intel
snd_hda_core
snd_hwdep
snd_pcm
snd_timer
intel_cstate
snd
intel_uncore
iTCO_wdt
iTCO_vendor_support
soundcore
dcdbas
intel_rapl_perf
sg
mei_me
pcspkr
evdev
serio_raw
lpc_ich
mfd_core
mei
battery
shpchp
parport_pc
ppdev
lp
parport
auth_rpcgss
oid_registry
sunrpc
ip_tables
x_tables
autofs4
ext4
crc16
jbd2
crc32c_generic
fscrypto
ecb
mbcache
hid_generic
usbhid
hid
sr_mod
cdrom
sd_mod
crc32c_intel
aesni_intel
aes_x86_64
glue_helper
lrw
gf128mul
ablk_helper
cryptd
psmouse
ahci
libahci
libata
i915
i2c_i801
scsi_mod
i2c_smbus
i2c_algo_bit
xhci_pci
ehci_pci
xhci_hcd
drm_kms_helper
ehci_hcd
r8169
mii
usbcore
drm
usb_common
fan
thermal
video
button

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 4th Gen Core Processor DRAM Controller [8086:0c00] (rev 06)
	Subsystem: Dell 4th Gen Core Processor DRAM Controller [1028:0612]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: hsw_uncore

00:02.0 VGA compatible controller [0300]: Intel Corporation 4th Generation Core Processor Family Integrated Graphics Controller [8086:041e] (rev 06) (prog-if 00 [VGA controller])
	Subsystem: Dell 4th Generation Core Processor Family Integrated Graphics Controller [1028:0612]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 29
	Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
	Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
	Region 4: I/O ports at f000 [size=64]
	[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: i915
	Kernel modules: i915

00:03.0 Audio device [0403]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller [8086:0c0c] (rev 06)
	Subsystem: Dell Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller [1028:0612]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 32
	Region 0: Memory at f7d14000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel

00:14.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI [8086:8c31] (rev 04) (prog-if 30 [XHCI])
	Subsystem: Dell 8 Series/C220 Series Chipset Family USB xHCI [1028:0612]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 27
	Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci_pci

00:16.0 Communication controller [0780]: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 [8086:8c3a] (rev 04)
	Subsystem: Dell 8 Series/C220 Series Chipset Family MEI Controller [1028:0612]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 30
	Region 0: Memory at f7d1e000 (64-bit, non-prefetchable) [size=16]
	Capabilities: <access denied>
	Kernel driver in use: mei_me
	Kernel modules: mei_me

00:1a.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 [8086:8c2d] (rev 04) (prog-if 20 [EHCI])
	Subsystem: Dell 8 Series/C220 Series Chipset Family USB EHCI [1028:0612]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at f7d1c000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci

00:1b.0 Audio device [0403]: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller [8086:8c20] (rev 04)
	Subsystem: Dell 8 Series/C220 Series Chipset High Definition Audio Controller [1028:0612]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 31
	Region 0: Memory at f7d10000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel

00:1c.0 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 [8086:8c10] (rev d4) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 24
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: df200000-df3fffff
	Prefetchable memory behind bridge: 00000000df400000-00000000df5fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:1c.3 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #4 [8086:8c16] (rev d4) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin D routed to IRQ 25
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: f7c00000-f7cfffff
	Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:1d.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 [8086:8c26] (rev 04) (prog-if 20 [EHCI])
	Subsystem: Dell 8 Series/C220 Series Chipset Family USB EHCI [1028:0612]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 0: Memory at f7d1b000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci

00:1f.0 ISA bridge [0601]: Intel Corporation C220 Series Chipset Family H81 Express LPC Controller [8086:8c5c] (rev 04)
	Subsystem: Dell C220 Series Chipset Family H81 Express LPC Controller [1028:0612]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: lpc_ich
	Kernel modules: lpc_ich

00:1f.2 SATA controller [0106]: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] [8086:8c02] (rev 04) (prog-if 01 [AHCI 1.0])
	Subsystem: Dell 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] [1028:0612]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 28
	Region 0: I/O ports at f0b0 [size=8]
	Region 1: I/O ports at f0a0 [size=4]
	Region 2: I/O ports at f090 [size=8]
	Region 3: I/O ports at f080 [size=4]
	Region 4: I/O ports at f060 [size=32]
	Region 5: Memory at f7d1a000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: <access denied>
	Kernel driver in use: ahci
	Kernel modules: ahci

00:1f.3 SMBus [0c05]: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller [8086:8c22] (rev 04)
	Subsystem: Dell 8 Series/C220 Series Chipset Family SMBus Controller [1028:0612]
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at f7d19000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at f040 [size=32]
	Kernel driver in use: i801_smbus
	Kernel modules: i2c_i801

02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 0c)
	Subsystem: Dell RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [1028:0612]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 26
	Region 0: I/O ports at e000 [size=256]
	Region 2: Memory at f7c00000 (64-bit, non-prefetchable) [size=4K]
	Region 4: Memory at f0000000 (64-bit, prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: r8169
	Kernel modules: r8169


** USB devices:
Bus 002 Device 002: ID 8087:8000 Intel Corp. 
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:8008 Intel Corp. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 005: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 003 Device 004: ID 045e:00cb Microsoft Corp. Basic Optical Mouse v2.0
Bus 003 Device 003: ID 413c:2005 Dell Computer Corp. RT7D50 Keyboard
Bus 003 Device 002: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


-- System Information:
Debian Release: 9.1
  APT prefers stable
  APT policy: (500, 'stable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386

Kernel: Linux 4.9.0-5-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8), LANGUAGE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)

Versions of packages linux-image-4.9.0-5-amd64 depends on:
ii  initramfs-tools [linux-initramfs-tool]  0.130
ii  kmod                                    23-2
ii  linux-base                              4.5

Versions of packages linux-image-4.9.0-5-amd64 recommends:
ii  firmware-linux-free  3.4
ii  irqbalance           1.1.0-2.3

Versions of packages linux-image-4.9.0-5-amd64 suggests:
pn  debian-kernel-handbook  <none>
ii  grub-pc                 2.02~beta3-5
pn  linux-doc-4.9           <none>

Versions of packages linux-image-4.9.0-5-amd64 is related to:
ii  firmware-amd-graphics     20161130-3
pn  firmware-atheros          <none>
pn  firmware-bnx2             <none>
pn  firmware-bnx2x            <none>
pn  firmware-brcm80211        <none>
pn  firmware-cavium           <none>
pn  firmware-intel-sound      <none>
pn  firmware-intelwimax       <none>
pn  firmware-ipw2x00          <none>
pn  firmware-ivtv             <none>
pn  firmware-iwlwifi          <none>
pn  firmware-libertas         <none>
ii  firmware-linux-nonfree    20161130-3
ii  firmware-misc-nonfree     20161130-3
pn  firmware-myricom          <none>
pn  firmware-netxen           <none>
pn  firmware-qlogic           <none>
ii  firmware-realtek          20161130-3
pn  firmware-samsung          <none>
pn  firmware-siano            <none>
pn  firmware-ti-connectivity  <none>
pn  xen-hypervisor            <none>

-- no debconf information

--- End Message ---
--- Begin Message --- 
Source: linux
Source-Version: 4.9.80-1

Hi,

On Wed, Jan 24, 2018 at 10:28:06AM +0100, John Hughes wrote:
> This bug appears to have been fixed somewhere between 4.9.65 and 4.9.77

Closing accordingly, thank you for reporting back.

Regards,
Salvatore

--- End Message ---
Reply to: